Audio Pro ACE-BASS 2 Manual

Audio Pro Ikke kategoriseret ACE-BASS 2

Læs gratis den danske manual til Audio Pro ACE-BASS 2 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Audio Pro ACE-BASS 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1) Volume control

2) Low pass crossover control

(variable 50Hz-100Hz)

3) Phase adjust 0 - 180

4) Standby mode switch-

Auto or ON

9) ON/OFF indicator

10) Mains switch

11) Mains cord (230V)

12) Fuse

(placed under)

WARNING !

To reduce the risk of electric shock, do not open or remove cover or back. Do not expose this appliance to rain or moisture. In case

of malfunction consult qualified service personel.

The exclamation point, within an equilateral triangle, is intended to alert

the user of the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

The lightning flash with arrowhead, within an equilateral

triangle, is intended to alert the user of the presence of

uninsulated "dangerous voltage" within the product´s

enclosure; that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

5) Low level input from amplifier

(LFE)

6) Line in/out from/to amplifier

(Line IN/OUT)

7) Speaker Level input

(from amplifier)

8) Speaker Level output

(to satellite speakers)

English

CONTROLS AND INDICATORS

O O

12 3 4 5 6 7 8 9

English

2.2 To Speaker output terminal (High level)

Connect speaker cables from the speaker terminals of your amplifier to the Speaker Level input of the subwoofer.

Carefully check the polarity of the cables (+ to + and - to -). Connect both Left and Right channels. The satellite

speakers are connected to SPEAKER OUTPUT on the subwoofer. Again, carefully check the polarity (+ to + etc).

In this installation, the satellite speakers HIPASS crossover frequency is automatically set to 100 Hz. If you want

the speakers to perform full frequency range, connect them to the main amplifier Speaker Output.

INSTRUCTIONS

Congratulations to your choice of Audio Pro subwoofer and to a new sound experience.

Audio Pro subwoofer is a unique product built with advanced technique. It is very easy to handle and install. It is

equipped with the unique Audio Pro ace-bass technique combined with the built-in amplifier, the long throw woofers

and the extremely solid cabinet offers a natural and deep bass reproduction at sound levels you never thought

existed.

The Audio Pro subwoofer offers extraordinary performance and lots of possibilities. In order to get the most out of

your new subwoofer, we recommend you to spend time and carefully read these instructions before you connect and

start up your system.

What is ace-bass ?

Normally, speaker design is bound to follow the laws of physics. The consequence will be, to get deep bass, the

speakerbox must be very large. With the ace-bass technique we can "change" the laws of physics in the way that the

driver believes it is placed in a much larger speaker box.

Furthermore, the ace-bass technology improves the driver performance. With the ace-bass technique, we can design

smaller subwoofers with deeper and cleaner bass.

2.1 To an amplifier / pre-amplifier with Subwoofer-out terminal, or pre-out/ main-in

Connect the enclosed cord from the subwoofer-output of your home cinema amplifier to LFE IN on the

subwoofer. When the LFE input is used, the built in Low Pass filter in the subwoofer is bypassed. You can also

connect to Line IN. (Then use the enclosed Y adaptor). In this case the Low Pass filter is in use. You can

adjust upper frequency between 50Hz to 100Hz. If you have a Dolby Pro Logic amplifier, you must connect it’s

Sub out to the Line IN of the subwoofer.

It can also be connected by using the Pre-out/Main-in from a two channel preamplifier/amplifier. The audio signal

is now connected from the Pre-out terminal to the Line IN on the subwoofer. By using the Low Pass control, the

upper frequency of the subwoofer can be continously adjusted from 50Hz-100 Hz. Signal is brought back to the

amplifier from Line OUT to Main-in on the amplifier.

Note: This connecting method requires 2 sets of RCA cables. These are not enclosed.

1. UNPACKING

Carefully unpack the Audio Pro subwoofer and check for any damages. If possible, keep the cartonbox if future

transportation is needed.

You should immediately contact your dealer if the subwoofer is damaged .

2. INSTALLATION

There are different methods to connect your subwoofer to a HiFi / Home Theater system. In the following we

explain different ways. NOTE! Do not connect the mains cord until all other installation is completed.

Produkt Specifikationer

Mærke:	Audio Pro
Kategori:	Ikke kategoriseret
Model:	ACE-BASS 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio Pro ACE-BASS 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Audio Pro Manualer

Audio Pro VOL-1 Manual

16 Juli 2025

Audio Pro SPW-5 Manual

10 Februar 2025

Audio Pro WAB-3 Manual

10 Februar 2025

Audio Pro TX-1 Manual

10 Februar 2025

Audio Pro C20 Manual

10 Februar 2025

Audio Pro C-SUB Manual

10 Februar 2025

Audio Pro DVD ONE Manual

30 Juli 2024

Audio Pro Living WR-200 Manual

24 Juli 2024

Audio Pro Porto docking speaker Manual

19 Juli 2024

Audio Pro Addon TWO Manual

31 Marts 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JILONG JL097205NPF Manual

14 September 2025

Brandson 306570 Manual

14 September 2025

Nedis PIM30012EGY Manual

14 September 2025

Neutrik SCD-W Manual

14 September 2025

BSS Audio FCS-926 Manual

14 September 2025

Brandson 303842 Manual

14 September 2025

AMX DGX-O-DXF-MMS Manual

14 September 2025

Brandson 304024 Manual

14 September 2025

JILONG JL097109NPF Manual

14 September 2025

Brandson 303403 Manual

14 September 2025