Audio-Technica ATND933a Manual

Audio-Technica Mikrofon ATND933a

Læs gratis den danske manual til Audio-Technica ATND933a (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Audio-Technica ATND933a, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ATND933aML & ATND933aWML MicroLine® Condenser

Hanging Microphones with Dante™ Network Output

MIC A

1.5 T IMES

DISTANCE “X”

MIC B

Figure 1 Figure 2

LESS THAN 2 TIMES “X”

DISTA

NCE “

X”

90°

ANGLE OF

ACCEPTANCE

Network Microphones

Features

• Wall/ceiling plate power module with Dante™ network output permits

permanent installation in standard, 2-gang electrical box and direct

connection to the network via Ethernet cable

• MicroLine® polar pattern provides narrow 90º acceptance angle

• Low-proﬁle design with low-reﬂectance ﬁnish for minimum visibility

• Superior o-axis rejection for maximum gain before feedback

• Logic input accepts external switch for connection to the Dante™ network

• UniGuard® RFI-shielding technology oers outstanding rejection of radio

frequency interference (RFI)

• UniSteep® ﬁlter provides a steep low-frequency attenuation to minimize

pickup of undesired ambient noise

• Available interchangeable elements permit angle of acceptance

from 90° to 360°

• Steel hanger positions microphone over choirs, instrumental groups

and theater stages

• Available in two colors: black (ATND933aML) and white (ATND933aWML)

Description

The ATND933aML is a wide-range miniature condenser microphone with

a MicroLine® (line cardioid) polar pattern. It is designed for quality sound

reinforcement. The combination of small size and excellent response makes the

microphone ideal for suspension over choirs, instrumental groups or theater stages.

The microphone is equipped with UniGuard® RFI-shielding technology, which oers

outstanding rejection of radio frequency interference (RFI).

The microphone’s MicroLine® (line cardioid) polar pattern provides a 90° angle

of acceptance. Additional interchangeable elements with omnidirectional (360°),

cardioid (120°) and hypercardioid (100°) pickup patterns are available.

The microphone includes a 15.2 m (50') permanently attached miniature cable. Its free

end connects to the provided ATND8734a Dante-enabled wall/ceiling plate power

module via a special TA3F-type connector designed to optimize RFI immunity. The

power module features a removable, circular cover plate that can be painted with

commercially available spray paint. The power module includes an RJ-45 output jack

for easy connection to the network via CAT5e (or better) cable. Additionally, logic input

screw terminals accept an external switch for connection to the Dante™ network.

The power module is equipped with an 80 Hz low-cut UniSteep® ﬁlter, three-position

input gain level selector (+30 dB, +40 dB and +50 dB), and red/green LED status

indicator, which can all be controlled remotely via third-party software.* Default settings

for the power module are as follows: low-cut ﬁlter o, +40 dB input gain, LEDs o.

The microphone comes equipped with a vinyl-coated steel hanger for positioning

over a choir/orchestra/stage, and a two-stage foam windscreen. The microphone is

enclosed in a rugged housing with a low-reﬂectance black ﬁnish. It is also available

with white housing, cable, hanger and windscreen as the ATND933aWML.

Installation and Operation

A uniform 90° angle of acceptance provides well-balanced audio pickup. The

microphone should be located forward of the front-most source, above the rear-most

source, and “aimed” between them (Fig.1). Increasing the height of the mic above

the sources will tend to equalize sound levels between them, but may also increase

background/reverberant sound pickup. When possible, the distance from the mic to

the rear-most source should be no more than twice the distance to the front source,

to maintain front-to-rear balance (Fig. 1).

Width of pickup is approximately 1.5 times the distance to the closest source. If

additional mics are needed for wide sources, they should be positioned apart laterally

at least 1.5 times the distance to the front source, to avoid phase cancellation (Fig. 2).

To orient the microphone in the proper direction, twist the housing slightly in its wire

holder. (Clockwise rotation moves the microphone to the right; counterclockwise

rotation moves it to the left.)

The provided two-stage foam windscreen simply snaps over the head of the

microphone, eectively reducing noise from wind or ventilation air currents.

The power module allows for remote control of a high-pass ﬁlter to provide easy

switching from a ﬂat frequency response to a low-end roll-o. The roll-o position

reduces the pickup of low-frequency ambient noise (such as trac, air-handling

systems, etc.), room reverberation and mechanically coupled vibrations. Mic gain and

LED ring color may also be controlled remotely through the power module.

The power module is equipped with logic input screw terminals which can be used

to trigger functions on compatible Dante-enabled devices, such as a video camera’s

pan/tilt or a rooms lighting preset.

The ATND8734a wall/ceiling plate power module is designed to be mounted in a

standard metal U.S. 2-gang electrical box. For safety and best performance, use the

electrical box only for the ATND8734a; do not include any AC power conductors.

Connect the TA3F-type connector on the microphone cable to the TB3M-type

connector in the power module plate.

Avoid leaving the microphone in the open sun or in areas where temperatures exceed

110° F (43° C) for extended periods. Extremely high humidity should also be avoided.

Note: Audio-Technica has developed a special RFI-shielding mechanism, which is an

integral part of the connectors in the Engineered Sound® line. If you remove or replace

the connector, you may adversely aect the unit’s RFI immunity. Audio-Technica oers

a crimp tool (ATCT) and RFI shields that enable you to shorten the cable and correctly

reinstall the connector while maintaining the highest level of RFI immunity.

ATND933aML & ATND933aWML

Audio-Technica Corporation

www.audio-technica.com

In the interest of standards development, A.T.U.S. oers full details

on its test methods to other industry

professionals on request.

1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL

1 Typical, A-weighted, using Audio Precision System One.

Speciﬁcations are subject to change without notice.

Fixed-charge back plate, permanently

polarized condenser

MicroLine® (line cardioid)

30-20,000 Hz

80 Hz, 18 dB/octave

-15 dBu @ +30 dB gain

-25 dBu @ +40 dB gain

-35 dBu @ +50 dB gain

73 dB, 1 kHz at 1 Pa

Microphone: 9.5 g (0.3 oz)

Power module: 330 g (11.6 oz)

Microphone: 146.5 mm (5.77") long,

8.0 mm (0.31") head diameter

Power module: 148.0 mm (5.83")

diameter x 47.0 mm (1.85") depth

Power module: RJ-45

Physical level: standard Ethernet

Connector: single RJ45

Cable quality: Shielded CAT5 or CAT6

recommended

Transmission speed: 100 Mbps

ESE-O omnidirectional (360°)

ESE-C cardioid (120°)

ESE-H hypercardioid (100°)

M14

ATND8734a wall/ceiling plate power

module with Dante™ network output;

AT8138 two-stage foam windscreen;

AT8452 steel hanger

ATND8734a wall/ceiling plate

power module with Dante™ network

output; AT8138(WH) two-stage foam

windscreen; AT8452(WH) steel hanger

Element

Polar pattern

Frequency response

Low frequency roll-o

Maximum input levels

Signal-to-noise ratio1

Weight

Dimensions

Output connector

Dante network

Optional interchangeable elements

Audio-Technica case style

Accessories furnished

ATND933aML

ATND933aWML

Speciﬁcations

12" or more on axis

LEGEN

Frequency in Hertz

Response in dB

10 dB

100

50 200 10k5k1k500 2k 20k

Roll-off

LEGEND

200 Hz

1 kHz

5 kHz

8 kHzSCALE IS 5 DECIBELS PER DIVISION

240˚

180˚

210˚

270˚

300˚

330˚ 0˚

150˚

120˚

90˚

30˚

60˚

frequency response: 30–20,000 Hz polar pattern

0.46"

11.6 mm

0.13"

3.2 mm

50'

15.2 m

5.77"

146.5 mm

5.17"

131.3 mm

0.31"

8.0 mm

5.83"

148.0 mm

3.16"

80.3 mm

1.85"

47.0 mm

1.45"

36.8 mm

Architect’s and Engineer’s Speciﬁcations

The microphone shall be a ﬁxed-charge condenser designed for permanent installation

or portable applications. It shall have a MicroLine® (line cardioid) polar pattern with a

uniform 90° angle of acceptance and a frequency response of 30 Hz to 20,000 Hz. It

shall be capable of accepting optional interchangeable elements for additional polar

patterns. It shall oer outstanding rejection of radio frequency interference (RFI).

The microphone shall have a permanently attached 15.2 m (50') miniature cable

terminating in a special TA3F-type output connector designed to optimize RFI immunity.

The output connector shall connect to a TB3M-type jack on the included power module.

The output connection on the power module shall be an RJ-45 terminal using standard

network protocol. Logic input screw terminals shall be provided to accept commercially

available external switches. The power module shall be capable of driving a Dante

audio ﬂow. The plate power module shall be designed to mount in a standard 2-gang

metal electrical box for ceiling or wall mounting. The power module shall contain an

80 Hz “low cut” switch to tailor the low-frequency response and minimize pickup of

unwanted sounds; it shall be selectable remotely via third-party software.* There

shall also be three gain levels (+30 dB, +40 dB, and +50 dB), selectable remotely via

third-party software. The power module shall include a red/green LED ring, controllable

via third-party software, and a removable, circular face plate that can be painted with

commercially available spray paint.

An adjustable steel wire hanger shall be provided for suspended installations. The steel

wire hanger shall attach to the microphone body and allow for the positioning of the

microphone without the need for tools. A two-stage foam windscreen shall also be

included.

The microphone shall be a hanging design, with an overall length of 146.5 mm (5.77")

and a head diameter of 8.0 mm (0.31"). Weight shall be 9.5 grams (0.3 oz) without

cable. The microphone, cable and steel hanger shall be black [white].

The Audio-Technica ATND933aML [ATND933aWML] is speciﬁed.

* For a list of compatible third-party software consult the “About Network Audio” page

at Audio-Technica.com.

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	ATND933a

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ATND933a stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATM355 Manual

1 Marts 2025

Audio-Technica BP892xCW Manual

13 Januar 2025

Audio-Technica ATGM2 Manual

6 December 2024

Audio-Technica Creator Pack Manual

6 December 2024

Audio-Technica AT2040 Manual

6 December 2024

Audio-Technica AE2500 Manual

6 December 2024

Audio-Technica AT881TH/RC Manual

6 December 2024

Audio-Technica AT882TH Manual

6 December 2024

Audio-Technica AT882TH/D3RC5 Manual

6 December 2024

Audio-Technica AT4033a Manual

6 December 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Kogan KAGMICBOMLA Manual

15 Juni 2025

Omnitronic UHF-601 Manual

14 Juni 2025

Omnitronic UHF-604 Manual

14 Juni 2025

Omnitronic UHF-602 Manual

14 Juni 2025

Neewer VM11 Manual

14 Juni 2025

Neewer KM23 Manual

13 Juni 2025

AmpliVox S1695 Manual

13 Juni 2025

Comica BooMax Manual

12 Juni 2025

DNA UWM 1 Manual

9 Juni 2025

DNA PSV 2 Manual

9 Juni 2025