Autel MaxiVideo MV105/108 Manual

Autel Ikke kategoriseret MaxiVideo MV105/108

Læs gratis den danske manual til Autel MaxiVideo MV105/108 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Autel MaxiVideo MV105/108, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Email: sales@autel.com

Web: www.autel.com

1. Removable Imager Head Cable – connects to the tool when performing

digital inspections for image and video viewing

2. Handgrip – ergonomically designed handle for comfortable grips and

agile operation

3. USB Cable – connects the Digital Inspection Camera to MaxiSys tablet

NOTE: The power of MaxiVideo inspection camera is directly

supplied by the USB port, and no external power source is needed.

The MaxiVideo Inspection Camera kit is supplied with useful accessories,

such as magnet, hook and mirror, which enable the video scope to perform

special tasks

For MV108 (with 8.5mm imager head)

For MV105 (with 5.5mm imager head)

Description

MV105 3/8’’ to 12’’ (0.95cm to 30cm)：

MV108 1’’ to 14’’ (2.54cm to 35.56cm)：

MV108 (640x480); MV105 (320 x 240)

Main Unit: 0°C to 50°C; Cable: -10°C to 70°C

-20°C to 75°C

Imager head and cable to 1m

0.3kg with 8.5mm diameter imager head

0.2kg with 5.5mm diameter imager head

FCC (EMC), CE (EMC and LVD)

Connect the Removable Imager

Head Cable to the Handgrip. Make

sure the key and slot are properly

aligned. Once they are aligned,

finger-tighten the knurled knob to

hold the connection firmly in place.

Power up the MaxiSys Tablet, and

select the “Digital Inspection”

application on the Job Menu.

Connect the MaxiVideo inspection

camera to the MaxiSys Tablet with

the USB connection, and that’s it!

1. Magnet – picks up small metal objects, such as dropped rings or screws

2. Hook – unclogs obstacles and picks up wires in the pipes or confined areas

3. Mirror – helps to look around corners and see the unreachable areas

The three accessories, including the Magnet, Hook, and Mirror, can be attached

to the Imager Head as described. Hold the accessory and the imager head.

Slip the end of the accessory over the imager head and then fix it as shown.

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority

to operate the equipment.

FCC Compliance

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur

in a particular installation.If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

The two accessories, both the Magnet and Mirror, can be attached to the

Imager Head as described. Hold the accessory and the imager head as shown.

Screw the thread part of the accessory over the imager head and then fix it.

1. Mirror – helps to look around corners and see the unreachable areas

2. Magnet - picks up small metal objects, such as dropped rings or screws

8.5mm Imager Head Accessories

5.5mm Imager Head Accessories

8.5mm

5.5mm

Item

Optimal Viewing Distance

Image Capture

Operating Temperature

Storage Temperature

Waterproof

Weight

Compliance

The MV105/108 digital inspection camera is designed to work with

MaxiSys series products or PC. It turns your MaxiSys tablet into a

video inspection scope, allowing you to examine difficult-to-reach

areas normally hidden from sight. It is capable of recording digital

still images and videos, which offers you an economical solution

to inspect machinery, facilities, and infrastructure in a safe and

quick way.

Produkt Specifikationer

Mærke:	Autel
Kategori:	Ikke kategoriseret
Model:	MaxiVideo MV105/108

Har du brug for hjælp?

Hvis du har brug for hjælp til Autel MaxiVideo MV105/108 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Autel Manualer

Autel EVO MAX 4T V2 Manual

9 December 2025

Autel EVO Max V2 Manual

6 December 2025

Autel MaxiSYS MS908S Pro Manual

12 September 2025

Autel MaxiEV BCE100 Manual

12 September 2025

Autel AutoLink AL549 Manual

3 August 2025

Autel MaxiAP AP2500E Manual

3 August 2025

Autel Care Premium Manual

3 August 2025

Autel MaxiAP AP2500 Manual

2 August 2025

Autel MAXISYS MS908CV II Manual

2 August 2025

Autel MaxiDiag MD906 Pro Manual

26 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

KoolStar Starter 950 Manual

25 December 2025

VOX SETSF5702B Manual

25 December 2025

Yamazen SUC-202 Manual

25 December 2025

Vaxcel OW37081 Manual

25 December 2025

Vaxcel T0253 Manual

25 December 2025

Reelcraft L 4525 123 7A Manual

25 December 2025

Reelcraft L 5700 Manual

25 December 2025

Viewsonic ViewBoard IN8621C Manual

25 December 2025

Yamazen YTY-A410 Manual

25 December 2025

BlaknBlu Oscar DSF Manual

25 December 2025