Auza Wave Packets Manual

Auza Syntese maskine Wave Packets

Læs gratis den danske manual til Auza Wave Packets (9 sider) i kategorien Syntese maskine. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Auza Wave Packets, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/9
WAVE PACKETS
Times for the T stages. Max time is s, and min time
is s (completely skipping the stage). If in CYCLE-PING
excitation mode or LINKED LFO mode, the T knobs have
a different functionality (refer to MODES on p./ p.).
PANEL OVERVIEW
PAGE
Wave Packets is a multi-talented complex modulation and audio source. The module allows you to craft 'wave packets', with each
of the main outputs deploying a different recipe from the contour function (linear segments between each time stage) and
frequency-dynamic oscillator (LFO or audio-rate oscillation which transitions through target frequencies) to produce a unique
modulation shape, burst of energy, or fragment/ phrase of audio.
CV Input with attenuverter for W (wave) parameter. Adds or subtracts to the
W knob position.
W-CV (WAVE CV)
Waveform shape of the oscillator, with continuous morphing in between the
main shapes.
W (WAVE)
Trigger output at end of a full wave packet cycle
EOC OUTPUT
Trigger output at end of each stage
EOS OUTPUT
4x T (TIME) CONTROLS
The toggle switch position determines the excitation mode (in conjuction with
the presence of a cable in the TRIGGER INPUT). Refer to MODES on p..
EXCITATION MODE SWITCH
This input is used to excite a wave packet. The presence of a cable in this
input is also used in conjunction with the
EXCITATION MODE SWITCH above
it to set the excitation mode. Refer to MODES on p..
TRIGGER INPUT
The sliders draw out a contour function (linear segments from each T stage
to the next), also referred to as the 'minimal contour line'.
3x D (DEPTH) SLIDERS
The glide control determines the uidity of change in the F frequencies.
With no glide at the counterclockwise position, turning the knob clockwise will
progressively increase the width of the transition time about the T/T and
T/T stage boundaries, with a linear-sounding glide always ensured.
>> (GLIDE)
CV Input with attenuverter for D (depth) parameter. Adds or subtracts to each
of the D slider positions.
D-CV (DEPTH CV)
CV input (V per octave) modulation of oscillator frequency - a global
frequency (or rate) shift. If in AUDIO frequency mode, plugging a cable in to
V/OCT will semitone-quantise the frequency selection on the F knobs.
If F-SYNC is also used, V/OCT will modulate the F-SYNC frequency at V/Oct.
V/OCT INPUT
main outputs ( unipolar and bipolar). Output (leftmost) provides a direct
feed from the contour function, output (rightmost) provides a direct feed
from the oscillator, and the remaining outputs use the contour function to
sculpt the oscillator output in to various wave packet forms.
Refer to the outputs description on p..
MAIN OUTPUTS
Tapping the button will toggle between LFO and AUDIO frequency modes.
- Holding down the button for s while in LFO frequency mode will toggle LINKED LFO mode on and off.
- Holding down the button while toggling the EXCITATION MODE SWITCH to the up (CYCLE) position will activate CYCLE-PING excitation mode.
- Holding down the button while moving the >> (glide) knob will change the oscillator phase in ° increments (along the knob 'dot' markings).
- Holding down the button while moving the W (wave) knob fully clockwise or counterclockwise will change the saw wave shape direction.
Additional Modes/ Shift Parameters Access:
BUTTON
The module's oscillator traverses through target frequencies during the
course of a wave packet, represented on the module panel from left to right
with colours: green {T}, blue {T, SUS, T} and purple {T}.
- In LFO frequency mode, the F knobs are independent rate (frequency)
controls, each centred at Hz. Each LED above the F knobs ashes a sine
pattern at the corresponding rate.
- In AUDIO frequency mode, the middle (blue) F knob sets the 'base'
frequency, centred on note C. The left and right F knobs set starting/ ending
pitch offsets to the middle base frequency with a ± octave range. Therefore
a frequency transition prole similar to a pitch envelope can be constructed,
trackable in pitch using
V/OCT. The LEDs represent frequency using a
colour spectrum, and indicate the relationship between the
F knobs.
3x F (FREQUENCY) CONTROLS
A tempo/ clock signal, LFO or audio oscillator output (primitive waveforms only)
can be plugged in to this input to clock in the oscillator frequency.
F-SYNC INPUT
- In AUDIO frequency mode, the 'base' frequency of the wave packet is set by
the F-SYNC frequency plus a pitch offset added by the middle F knob. The left
and right F knobs add starting/ ending pitch offsets to this base.
- In LFO frequency mode, the F knobs function as individual clock dividers/
multipliers to the F-SYNC clock rate.

Produkt Specifikationer

Mærke: Auza
Kategori: Syntese maskine
Model: Wave Packets

Har du brug for hjælp?

Hvis du har brug for hjælp til Auza Wave Packets stil et spørgsmål nedenfor, og andre brugere vil svare dig


Syntese maskine Auza Manualer

Auza

Auza Wave Packets Manual

24 December 2025

Syntese maskine Manualer

Nyeste Syntese maskine Manualer

Mutable Instruments

Mutable Instruments Plaits Manual

1 December 2025
Erica Synths

Erica Synths Snare Manual

30 November 2025
Melbourne Instruments

Melbourne Instruments Nina Manual

5 November 2025
Behringer

Behringer SKIES Manual

21 Oktober 2025
Alright Devices

Alright Devices T-Wrex Manual

12 Oktober 2025
Sequential

Sequential Prophet X Manual

8 Oktober 2025
Sequential

Sequential Prophet 5 Manual

7 Oktober 2025
Electro Harmonix

Electro Harmonix Synth9 Manual

6 Oktober 2025
UDO-Audio

UDO-Audio Super 6 Manual

30 September 2025
Novation

Novation Summit Manual

12 September 2025