B-Tech BT7819-888 Manual

B-Tech Vægophæng BT7819-888

Læs gratis den danske manual til B-Tech BT7819-888 (2 sider) i kategorien Vægophæng. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11 anmeldelser. Har du et spørgsmål om B-Tech BT7819-888, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

page 2

BT7819-888

mounting instructions

Slide the collar on the ball-joint bracket . Insert the safety pin into the hole at the corner of the (Diagram A)

collar, make sure that the safety pin is inserted through the ball-joint bracket . Use either the (Diagram B)

finger screws for quick release and easy installation , or the security allen screws, to secure collar (Diagram C)

position on the ball-joint bracket . (Diagram D)

Assemble the ball-joint mount before installation on the pole. Drill holes on the Ø50mm

(2”) pole.

*For the poles that are not supplied from

B-Tech.

Slide the collar and ball-joint onto the pole.

2 3

Assemble carousel

disc to ball-joint

bracket, using the

square end allen

screw with spring

washer . (Diagram I)

Once securely

attached, fasten

brake screw

into ball-joint arm

(Diagram J). (This

will stop carousel disc

from unnecessarily

rotating once

mount is installed).

Assemble carousel disc to

ball joint bracket.

Rotate the projector to desired position.

Slide collar and ball-joint up onto the pole . Insert the safety bolt through the(Diagram E)

retaining plate, collar and pole ). Fasten brake screws into the thread holes to(Diagram F

the position of the collar (Diagram G).

Choose the correct legs for the projector:

1. Number of legs chosen depends

on the number of mounting holes on the

projector. (Where possible, use 4 legs).

2. The size of the legs depends on where

the carousel disc is placed. Mount the

carousel disc as close as possible to the

centre of gravity of the projector.

*The centre of the projector is not always the

centre of gravity, as the weight may be unevenly

distributed.

Please see for your reference on the legs mounting.Diagram H

3. Check the projector’s manual for screw sizes (M3, M4, M5 or M6).

If the projector has recessed holes, or has an uneven mounting surface,

then choose suitable spacers and/ or washers with spring washers to

allow for a level mounting. Do NOT overtighten.

Mount the legs on the projector.

3 mounting holes,

2 short legs and 1

long leg.

4 mounting holes,

2 short legs and 2

long leg.

Ø10.5mm

20mm (minimum distance

from the end of the pole to

the center of the hole)

Drill Ø10.5mm hole horizontally straight through

the pole at the distance from the end of the pole to

the center of the hole.

Position the carousel

disc so that the legs

fit into the slots.

Use either the hand

wheels for easy access

to projector light blub

(Diagram K), or the

locking dome nuts

to secure leg position

on carousel disc

(Diagram L). Tighten

the screws, fixing the

legs to the projector.

Mount projector to the carousel disc.

page 3

Diagram K Diagram L

The Aviball arm allows the projector to move freely 37º in any direction or to rotate 360º . To increase (Diagram M) (Diagram N)

stiffness of arm and to lock projector in position, use the spanner to make a small adjustment of the M8 bolt on the ball-joint brac

.(Diagram O)

Adjust M8 hexagon bolt

Adjust M8 hexagon bolt on the ball joint bracket to alter

the tension of the ball-joint. Make sure that the stiffness of

ball-joint can hold the projector in place after moving.

Attach the cover plates over

the carousel disc.

To complete installation attach the two halves of the

carousel cover plate over the carousel disc.

Diagram M Diagram N Diagram O

Diagram I Diagram J

BT7819-888

mounting instructions

Diagram A Diagram B Diagram C Diagram D

Diagram E Diagram F Diagram G

Diagram H

11 35

18 19

21 2625

Produkt Specifikationer

Mærke:	B-Tech
Kategori:	Vægophæng
Model:	BT7819-888
Produktfarve:	Sort
Monteringstype:	Loft
Rotationsvinkel:	360 °
Maksimal vægtkapacitet:	15 kg
Drejelig vinkel:	37 °