Balance RF-WS98 Manual

Balance Vejrstation RF-WS98

Læs gratis den danske manual til Balance RF-WS98 (15 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Balance RF-WS98, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/15

All-In-One Wireless Professional Weather Station (DCF) (975246) User’s Manual

Functions

-Weather forecast with sunny, partly cloudy, cloudy, rainy and stormy

-Barometric pressure display

-Wind direction display

-Average & gust wind speed with storage of the minimum and maximum measured values

-Daily, weekly, monthly and total rainfall display

-Lightning detection with estimated number of lightning strike and distance display

-Lightning alert indication (Approaching, Departing & Overhead) and alarm setting

-Daily maximum and current UV Index with estimated exposure time display

-Room temperature and interior humidity display with storage of the minimum and maximum

measurement values

-Outside temperature and outside humidity display with storage of the minimum and maximum

measured values

-Dew point, heat index & wind chill display

-Ice/frost alert

-Radio-controlled DCF-77 time signal reception with time display, time-zone setting

-Date display

-Alarm clock with snooze function

In this package you will find:

-One monitor (main unit)

-One Transmitter (Transmits Wind, Rain, UV, Lightning, Temperature/humidity data)

-4 pieces of Nylon straps

-One owner’s’ manual

-Power adapter for the monitor

Additional tools needed for installation

-Small Phillips screwdriver

-Mast, 1 – 1.25 inch (2.54 – 3.18 cm) in diameter (to mount the transmitter)

Installation

Choose a suitable location for your transmitter

-The transmitter must be set up outdoors

-The transmitter must be located within the signal transmission range (100 meters line of sight). Walls and

obstructions reduce the transmission range. Check the signal reception on the weather station before final

assembly.

-Ideally the transmitter should be mounted on a mast or roof of a house, and in an open area where wind,

rain & sunlight can access the transmitter from all sides to enable the wind force, wind direction, rainfall &

UV Index to be measured accurately

-Avoid placing the transmitter close to any electromagnetic radiation sources such as electricity tower or

electrical equipments as the lightning detection will be greatly affected.

-Ensure that the wind vane and the wind wheel are not blocked to guarantee accurate measurements.

-The transmitter should be mounted in an open area where sunlight can shine directly on the UV sensor of

the transmitter any time of the day and is not blocked by tree or wall.

-Do not position under trees or next to walls. The rain must be able to fall on the transmitter without

obstructions to achieve an accurate rainfall measurement.

-Ensure that rain water does not accumulate under the transmitter. It must be able to flow off freely.

Testing the effective transmission range

1) Place the transmitter to your selected outdoor location in horizontal position (see above section) and the

transmitter must be at least 1 meter above ground. (This is not the final assembly and do not permanently

mount the transmitter on a mask or roof at this stage until the effective transmission range is verified)

2) Open the battery door of the transmitter and insert 4 pieces of AA batteries according to the battery polarity

indicated. Close the battery door and tighten the screws.

3) Place the main unit to your selected indoor location. Connect power adapter to the back of the main unit or

insert 3 pieces of AA batteries in the battery compartment.

4) Press [clock/set] button once to skip the initial weather setting

5) The main display will flash indicating it is in the searching mode

(If the main display stops flashing, you may hold the [Search] button for 3 seconds on the main unit to

enforce RF searching)

6) While the main unit is in searching mode, press the [Transmit] button on the bottom of the transmitter to

transmit RF signal to the main unit

7) If they are within the effective transmission range, all the readings including outdoor temperature, humidity,

wind speed, wind direction, rainfall & UVI will display on the main unit.

8) To ensure good RF reception signal, try turning the wind wheel & change the direction of the wind vane on

the transmitter and you should notice the wind speed & direction update within 2 minutes.

If the display reading does not update every minute, the RF reception signal is still poor. Shorten the

transmitter and repeat above transmission range test until you have the display reading updated every 1

minute to ensure good RF reception signal.

9) After testing the effective transmission range, remove all batteries from the transmitter. Remove all

batteries and disconnect the power adapter from the main unit.

Installation and Calibration

Produkt Specifikationer

Mærke:	Balance
Kategori:	Vejrstation
Model:	RF-WS98

Har du brug for hjælp?

Hvis du har brug for hjælp til Balance RF-WS98 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Balance Manualer

Balance RF-WS98 Manual

27 Juli 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

La Crosse Technology WS7006 Manual

30 September 2025

23 September 2025

23 September 2025

23 September 2025

21 September 2025

Brandson 305419 Manual

15 September 2025

Brandson 306643 Manual

15 September 2025

Brandson 304632 Manual

15 September 2025

Brandson 304577 Manual

14 September 2025

Brandson 304465 Manual

14 September 2025