Bauknecht B7F HS51 X Manual

Bauknecht Opvaskemaskine B7F HS51 X

Læs gratis den danske manual til Bauknecht B7F HS51 X (6 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Bauknecht B7F HS51 X, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
EN
1
Daily Reference Guide
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
FIRST TIME USE
Before using the appliance carefully read
product available on website: docs.bauknecht.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the Settings (Half Load ) button for 3 seconds until you hear
a beep.
3. After one second the rst available setting (letter „h”) will be displayed.
4. Press button to scroll through the list of available settings (see ta-
ble below), then press START/Pause to view and change the value of
the currently selected setting.
5. Press button to change the value, then press START/Pause to
save the new value.
6. To change another setting, repeat points 2 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 0,5 kg); it is not un-
usual for a little water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run a program every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in a perfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is “3”.
See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on the heater, contributing also to better cleaning
eciency. This system regenerates itself with salt, therefore it is re-
quired to rell the salt container when empty. The frequency of regen-
eration depends on the water hardness level setting - regeneration takes
place once per Eco cycles with the water hardness level set to 4-6 3. The
regeneration process occurs at the beginning of the cycle with additional
fresh water.
• Single regeneration consumes: ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A
lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of levels can be set according to the dishwasher model. 6
• If you see bluish streaks on the dishes, set a low number (0-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
A
B
LETTER SETTING
VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”)
1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 | 4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included in
the settings menu.
-
CONTROL PANEL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
1. ON-OFF/Reset button with indicator light
2. Eco program button with indicator light
3. Auto Intensive program button with indicator light
4. Auto Mixed program button with indicator light
5. Auto Fast program button with indicator light
6. Rapid program button with indicator light
7. Crystals program button with indicator light
8. Prewash program button with indicator light
9. Salt reservoir empty indicator light
10. Rinse Aid reservoir empty indicator light
11. Display
12. Program number remaining time and indicator
13. Closed water tap indicator light
14. DESCALE indicator light
15. Power Clean® option button with indicator light
16. Half Load option Settings button with indicator light/ - 3 sec. press
17. Extra Dry option button with indicator light
18. Silent option Key lock button with indicator light/ - 3 sec. press
19. Sani Rinse option button with indicator light
20. Self-Clean program button with indicator light
21. Delay option button with indicator light
22. START/Pause button with indicator light
Water Hardness Table
Level
°dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (soft) 0 - 6 0 - 10 0 - 7
2 (medium) 7 - 11 11 - 20 8 - 14
3 (average) 12 - 16 21 - 29 15 - 20
4 (hard) 17
- 34 30 - 60 21 - 42
5 (very hard) 35 - 50 61 - 90 43 - 62

Produkt Specifikationer

Mærke: Bauknecht
Kategori: Opvaskemaskine
Model: B7F HS51 X

Har du brug for hjælp?

Hvis du har brug for hjælp til Bauknecht B7F HS51 X stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Bauknecht Manualer

Bauknecht

Bauknecht IBBO 3C26 X Manual

11 November 2025
Bauknecht

Bauknecht OBUC Ecosilent 9760 Manual

9 November 2025
Bauknecht

Bauknecht BKR PAS Manual

9 November 2025
Bauknecht

Bauknecht BKR IAS Manual

9 November 2025
Bauknecht

Bauknecht BKR FAS Manual

7 November 2025
Bauknecht

Bauknecht BKO UBM Manual

1 November 2025
Bauknecht

Bauknecht BKO IBM Manual

31 Oktober 2025
Bauknecht

Bauknecht BKR UAS Manual

31 Oktober 2025
Bauknecht

Bauknecht BKO PBM Manual

29 Oktober 2025
Bauknecht

Bauknecht B8I HT58 TS Manual

30 September 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Arçelik

Arçelik 6586 SC Manual

11 December 2025
Siemens

Siemens SN63EX22AE Manual

11 December 2025
Arçelik

Arçelik 6386 SC Manual

11 December 2025
Siemens

Siemens SX65ZX01CH Manual

11 December 2025
Siemens

Siemens SR63EX25KE Manual

11 December 2025
Arçelik

Arçelik 6343 S Manual

11 December 2025
Siemens

Siemens SR63EX24KE Manual

11 December 2025
Siemens

Siemens SX53ES22CE Manual

11 December 2025
Siemens

Siemens SR63HX74ME Manual

11 December 2025
Siemens

Siemens SN55ZS07CE Manual

11 December 2025