Behringer 911 Envelope Generator Manual

Behringer Syntese maskine 911 Envelope Generator

Læs gratis den danske manual til Behringer 911 Envelope Generator (2 sider) i kategorien Syntese maskine. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Behringer 911 Envelope Generator, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Quick Start Guide
911 ENVELOPE GENERATOR
Legendary Analog Envelope Generator
Module for Eurorack
Controls
(1) T1 (Attack) – Controls the envelope attack time from
2 ms to 10 seconds.
(2) T2 (Decay) – Controls the envelope decay time from 2 ms
to 10 seconds.
(3) T3 (Release) – Controls the envelope release time from
2 ms to 10 seconds.
(4) E sus (Sustain) – Controls the sustain time from 0 or
10 seconds.
(5) S-TRIG IN – Connect an external trigger signal via 3.5 mm
TS cable.
(6) OUT – Send the envelope to another module via 3.5 mm
TS cable.
Power Connection
The 911 comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the  nal position has been established, tighten the
screws down.
(1)
(3)
(4)
(5) (6
)
(
2)
Speci cations
Trigger Input
Type 3.5 mm jack, DC coupled
Impedance 5 kΩ, unbalanced
Maximum input level +10 V
Trigger operation Active low, hold low
until release
Envelope Output
Type 3.5 mm jack, DC coupled
Impedance > 200 Ω, unbalanced
Maximum output range 0 V to +6 V DC
Controls
T1 (Attack) 2 ms - 10 s
T2 (Decay) 2 ms - 10 s
T3 (Release) 2 ms - 10 s
E sus (Sustain) 0 V to +5.5 V DC
Power
Power supply Eurorack
Current draw 30 mA (+12 V),
30 mA (-12 V)
Physical
Dimensions 35 x 40 x 129 mm
(1.4 x 1.6 x 5.1")
Rack units 8 HP
Weight 0.09 kg (0.2 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be su ered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical speci cations, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China

Produkt Specifikationer

Mærke: Behringer
Kategori: Syntese maskine
Model: 911 Envelope Generator

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer 911 Envelope Generator stil et spørgsmål nedenfor, og andre brugere vil svare dig


Syntese maskine Behringer Manualer

Behringer

Behringer DeepMind 12X Manual

6 Juli 2025
Behringer

Behringer Vocoder VC16 Manual

6 Juli 2025
Behringer

Behringer DeepMind 12XD Manual

6 Juli 2025
Behringer

Behringer WASP VCF Manual

5 Juli 2025
Behringer

Behringer 2-XM Manual

3 Juni 2025
Behringer

Behringer STEPS Manual

30 Januar 2025
Behringer

Behringer WAVE Manual

2 Januar 2025
Behringer

Behringer PHARA-O MINI Manual

2 Januar 2025
Behringer

Behringer Eurorack GO Manual

15 November 2024
Behringer

Behringer RS-9 Manual

10 Oktober 2024

Syntese maskine Manualer

Nyeste Syntese maskine Manualer

Moog

Moog MiniVoyager RME Manual

27 Juli 2025
Moog

Moog Little Phatty Stage II Manual

27 Juli 2025
Waldorf

Waldorf Quantum MK2 Manual

26 Juli 2025
Moog

Moog MiniModel D Manual

26 Juli 2025
Boss

Boss SY-1000 Manual

23 Juli 2025
Moog

Moog Messenger Manual

19 Juni 2025
Motas Electronics

Motas Electronics Motas-6 Manual

17 Juni 2025
Roland

Roland JUNO-D8 Manual

1 Juni 2025
Qu-Bit

Qu-Bit Chance Manual

4 Marts 2025
Twisted Electrons

Twisted Electrons TWISTfm FM Manual

2 Februar 2025