Behringer System 100 172 Phase Shifter/Delay/LFO Manual

Behringer Syntese maskine System 100 172 Phase Shifter/Delay/LFO

Læs gratis den danske manual til Behringer System 100 172 Phase Shifter/Delay/LFO (2 sider) i kategorien Syntese maskine. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Behringer System 100 172 Phase Shifter/Delay/LFO, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Quick Start Guide
SYSTEM 100
172 PHASE SHIFTER/
DELAY/LFO
Legendary Analog Phase Shifter/
Delay/LFO Module for Eurorack
Controls
(1) CV IN – Accepts voltage from an external source to
control or modulate the phase shifter frequency or audio
delay time. If no jack is inserted the LFO can be used to
modulate the eect.
(2) MOD INTENSITY – Controls how much the eect is
modulated by the LFO or external CV input.
(3) EFFECT ON/OFF – Engages or disengages the
eect section.
(4) SHIFT FREQ – Adjusts the frequency of the phase shifter.
(5) SIG IN – Accepts an incoming signal via 3.5 mm TS cable.
(6) SIG OUT – Sends the signal from the eect section.
(7) RESONANCE – Adjusts the amount of signal that is fed
back through the eect.
(8) DELAY TIME – Adjusts the time of the delay eect.
(9) FREQUENCY – Controls the LFO output frequency.
(10) LFO OUT – Sends the LFO signal as a triangle and inverted
triangle wave.
(11) THRESHOLD – Controls the input voltage level required to
trigger the gate.
(12) GATE IN – Accepts an incoming gate signal via 3.5 mm
TS cable.
(13) GATE OUT – Send the gate delay signal via 3.5 mm
TS cable.
(14) GATE TIME – Controls the gate length.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
(1)
(2)
(8)
(6)(5)(4)
(11) (14)
(7)
(13)
(9)
(10)
(3)
(12)
Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series ofxed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
Specications
Inputs
Phase shifter signal input
Type 3.5 mm TS jack, AC coupled
Impedance 70 kΩ, unbalanced
Max input level +16 dBu
Phase shifter CV input
Type 3.5 mm TS jack, DC coupled
Impedance >50 kΩ, unbalanced
Max input level +10 V
CV range 0 V to +10 V
Audio delay signal input
Type 3.5 mm TS jack, AC coupled
Impedance 15 kΩ, unbalanced
Max input level +20 dBu
Audio delay CV input
Type 3.5 mm TS jack, DC coupled
Impedance >70 kΩ, unbalanced
Max input level +10 V
CV range 0 V to +10 V
Gate input
Type 3.5 mm TS jack, DC coupled
Impedance 47 kΩ, unbalanced
Max input level +10 V
CV range 0 V to +10 V
Outputs
Phase shifter signal output
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level +18 dBu
Audio delay signal output
Type 3.5 mm TS jack, DC coupled
Impedance 1 kΩ, unbalanced
Max output level +16 dBu
LFO output
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 1.2 kΩ
Max output level 10 V p-p
Gate output
Type 3.5 mm TS jack, DC coupled
Impedance 500 Ω
Max output level +5 V
Controls
Phase shifter eect switch O / on
Phase shifter mod intensity -∞ to unity gain
Phase Shift frequency 200 Hz to 8 kHz
Phase shifter resonance O to maximum resonance
Audio delay eect switch O / on
Audio delay mod intesity -∞ to unity gain
Audio delay time 1 ms to 7 ms
Audio delay resonance O to maximum resonance
LFO frequency 0.02 Hz to 10 Hz
Gate Threshold 0.3 V to 5 V
Gate delay time 0.3 ms to 6 s
Gate time 0.3 ms to 6 s
Power
Power Eurorack supply
Current 60 mA (+12 V), 60 mA (-12 V) draw
Physical
Dimensions 44 x 81 x 129 mm
(1.7 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.19 kg (0.42 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.

Produkt Specifikationer

Mærke: Behringer
Kategori: Syntese maskine
Model: System 100 172 Phase Shifter/Delay/LFO

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer System 100 172 Phase Shifter/Delay/LFO stil et spørgsmål nedenfor, og andre brugere vil svare dig


Syntese maskine Behringer Manualer

Behringer

Behringer DeepMind 12X Manual

6 Juli 2025
Behringer

Behringer Vocoder VC16 Manual

6 Juli 2025
Behringer

Behringer DeepMind 12XD Manual

6 Juli 2025
Behringer

Behringer WASP VCF Manual

5 Juli 2025
Behringer

Behringer 2-XM Manual

3 Juni 2025
Behringer

Behringer STEPS Manual

30 Januar 2025
Behringer

Behringer WAVE Manual

2 Januar 2025
Behringer

Behringer PHARA-O MINI Manual

2 Januar 2025
Behringer

Behringer Eurorack GO Manual

15 November 2024
Behringer

Behringer RS-9 Manual

10 Oktober 2024

Syntese maskine Manualer

Nyeste Syntese maskine Manualer

Moog

Moog MiniVoyager RME Manual

27 Juli 2025
Moog

Moog Little Phatty Stage II Manual

27 Juli 2025
Waldorf

Waldorf Quantum MK2 Manual

26 Juli 2025
Moog

Moog MiniModel D Manual

26 Juli 2025
Boss

Boss SY-1000 Manual

23 Juli 2025
Moog

Moog Messenger Manual

19 Juni 2025
Motas Electronics

Motas Electronics Motas-6 Manual

17 Juni 2025
Roland

Roland JUNO-D8 Manual

1 Juni 2025
Qu-Bit

Qu-Bit Chance Manual

4 Marts 2025
Twisted Electrons

Twisted Electrons TWISTfm FM Manual

2 Februar 2025