Bestway Retro Groove 53164 Manual

Bestway Ikke kategoriseret Retro Groove 53164

Læs gratis den danske manual til Bestway Retro Groove 53164 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Bestway Retro Groove 53164, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
1 / 4
Instruction Manual
Manual ID 2024M-00035
Play Center with Slide Manual
OWNER’S MANUAL
WARNING
Never leave your child unattended – drowning hazard.
KEEP ASSEMBLY AND INSTALLATION INSTRUCTION FOR FUTURE REFERENCE. THE TOY CONTAINS SMALL PARTS, IT SHOULD BE
Only for domestic use.
Only for outdoor use.
Children can drown in very small amounts of water. Empty the pool when not in use.
Do not install the paddling pool over concrete, asphalt or any other hard surface.
Place the product on a level surface at least 2 m from any structure or obstruction such as a fence, garage, house, overhanging branches,
laundry lines or electrical wires.
Recommend back towards the sun when playing.
Modification by the consumer of the original paddling pool (for example the addition of accessories) shall be carried out according to the
instructions of the manufacturer.
Make sure the pool and slide are always connected while in use; do not exceed the maximum weight: 45 kg / 99 lbs. One person on the slide at
a time. For 53097, do not exceed the maximum weight: 144kg / 317lbs, and the maximum users on the slide is two persons at a time.
Children must remove shoes and glasses, as well as any sharp or hard objects from their pockets, as they may puncture the slide surface.
Always keep the slide entrance free from obstruction.
Do not allow food, drink or gum inside unit.
Do not allow users to do somersaults or rough play.
Do not allow users to climb or hang on containing walls.
Do not use the product if wind speed exceeds 20mph.
Do not use the product during inflation and deflation.
Incorrect assembly could result a potential hazard.
As the red connector is an important connection part, it needs to be tightened durning installation.
SETUP
CHOOSE THE CORRECT LOCATION
Because of the combined weight of the water inside the pool and the users, it is important that the surface chosen to install the pool is capable
of uniformly supporting the total weight for the entire time the pool is installed.
An adequate drainage system has to be provided to deal with overflow water. During filling, draining or when in use, water may flow out of the
pool.
The surface must be flat and smooth. If the surface is inclined or uneven, it can damage the structure of the pool and the welding point.
2 / 4
The selected surface must be clear of any type of object. Due to the weight of the water, any object under the pool could damage or perforate
the material on the bottom.
The selected surface must be clear of aggressive plants and weed species. Those types of strong vegetation could grow through the liner and
create water leakage. The grass or other vegetation that may cause odor or slime to develop has to be eliminated from the set-up location.
The selected location must not have overhead power lines or trees. Be sure the location does not contain underground utility pipes, lines or
cables of any kind.
The selected position must be far from house entrance. Do not position any equipment or other furniture around the pool. The water that comes
out of the pool during the use or due to a faulty product can damage the furniture inside the house or surrounding the pool.
Suggested set-up surfaces: grass, ground and all other surfaces that respect the above set-up conditions.
Not suggested surfaces: mud, sand, gravel, deck, balcony, driveway, platform, soft/loose soil or other surface that does not meet the above
set-up conditions.
ASSEMBLY
Warning: Adult assembly required.
1. Open the water valve to fill water in the water chamber. (Only for product with water chamber)
2. Open the 3-interconnecting valve to fill water in the water chamber and close the first cap, then inflate the same chamber with air pump (not
included). Close the valve after inflation and press it into the air chamber. (Only for product with 3-interconnecting valve)
3. Open the safety valves and inflate the parts one by one. Be sure to close the valves after inflation. Air pump is not included.
NOTE: Do not over inflate. Do not use either an air compressor or compressed air.
NOTE: For inflatable floor, the air valve is on the bottom side of the product.

Produkt Specifikationer

Mærke: Bestway
Kategori: Ikke kategoriseret
Model: Retro Groove 53164

Har du brug for hjælp?

Hvis du har brug for hjælp til Bestway Retro Groove 53164 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Bestway Manualer

Bestway

Bestway Hydro-Force 6531M Manual

31 Juli 2025
Bestway

Bestway Hydro-Force 6531R Manual

31 Juli 2025
Bestway

Bestway 561KM Manual

7 Juli 2025
Bestway

Bestway H2OGO! 52725 Manual

6 Juli 2025
Bestway

Bestway Lay-Z-Spa 60263 Manual

6 Juli 2025
Bestway

Bestway Lay-Z-Spa 6002Q Manual

6 Juli 2025
Bestway

Bestway Lay-Z-Spa 60199 Manual

6 Juli 2025
Bestway

Bestway 98019 Manual

5 Juli 2025
Bestway

Bestway 9103C Manual

5 Juli 2025
Bestway

Bestway 9102O Manual

5 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ADDAC System

ADDAC System ADDAC320 Manual

31 Juli 2025
Zoom

Zoom S6 SessionTrak Manual

31 Juli 2025
Advantech

Advantech PCE-7132 Manual

31 Juli 2025
Tripp Lite

Tripp Lite Protect It! TLP1008TELTV Manual

31 Juli 2025
Emos

Emos ZM6125 Manual

31 Juli 2025
Tripp Lite

Tripp Lite Protect It! TLM812SA Manual

31 Juli 2025
Advantech

Advantech ROM-DB5900 Manual

31 Juli 2025
Emos

Emos ZM5155 Manual

31 Juli 2025
Tripp Lite

Tripp Lite TLM406NC Manual

31 Juli 2025
Tripp Lite

Tripp Lite Protect It! TLP76RBTEL Manual

31 Juli 2025