Vaxcel T0696 Manual

Vaxcel Ikke kategoriseret T0696

Læs gratis den danske manual til Vaxcel T0696 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Vaxcel T0696, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

Page 1 / 5

Important to Know:

1. If you are not familiar with state and local electrical

codes, it is recommended that you consult with a

qualified electrician.

2. This fixture requires a 120 VAC, 60 Hz power

source.

3. For general safety and to avoid any possible

damage to the sensor, be sure the power is

switched "off" before adjustment.

Maximum Wattage: 2-150 W (bulb not included)

Working Temperature Range: - 13°F ~ 113°F

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

T0696 / T0697

Features:

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Note: Fixture can be wall mounted or eave mounted.

Wall Mounted

Eave Mounted

Read notes section on page 4 for additional information about mounting location of fixture.

Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)

Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for

proper operation and to avoid the risk of electrical shock.

1. Motion sensor: turns light ON automatically when

motion is detected and turns light OFF or remains

in low-level brightness when motion stops.

2. Photocell keeps the light OFF during daylight hours.

Hardware Package (included):

Decorative cover

Fixture Mounting Screw

Mounting Strap

Wire Connector

Gasket

Mounting Screw X2

#8/32X1/2 in

Mounting Screw X2

#6/32 X1/2 in

Mounting Screw X2

#10/24 X1/4 in

For eave mounted only:

Rotate the sensor head towards the back plate.

Rotate the sensor head clockwise 180˚ so the controls face down.

Controls

Backplate

Controls

(1) Phillips-head Screwdriver

1. Phillips-head screwdriver for attaching mounting screws to

mounting strap, mounting bracket and fixture to mounting bracket.

Tools Needed:

221031

Produkt Specifikationer

Mærke:	Vaxcel
Kategori:	Ikke kategoriseret
Model:	T0696

Har du brug for hjælp?

Hvis du har brug for hjælp til Vaxcel T0696 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Vaxcel Manualer

17 December 2025

17 December 2025

17 December 2025

17 December 2025

17 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

16 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

TOTO TSMX Manual

17 December 2025

Gamdias Aura GC2 Manual

17 December 2025

Grundig Miami 49 VLX 9670 BP Manual

17 December 2025

Silverstone UC01 Manual

17 December 2025

Liteline P-4020 Manual

17 December 2025

Televés DTKom 534120 Manual

17 December 2025

TOTO TBN01105U Manual

16 December 2025

NightStick INTRANT DUO XPP-5564GXA Manual

16 December 2025

TOTO TS200FL41 Manual

16 December 2025

Vinotemp EL-168COMM Manual

16 December 2025