Beverage-Air LV15-1 Manual


Læs gratis den danske manual til Beverage-Air LV15-1 (13 sider) i kategorien Køleskab. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Beverage-Air LV15-1, eller vil du spørge andre brugere om produktet?

Side 1/13
809-096A
Rev. A
Beverage Air
IMPORTANT
INFORMATION
FOR
LV SERIES
This cooler has passed the
QUALITY CONTROL INSPECTION
And meets the high standards at Beverage-Air
This inspection includes complete refrigeration
System, cabinet construction & nish.
IMPORTANT
PLEASE RETAIN FOR YOUR RECORDS
SALES OFFICE: 3779 CHAMPION BLVD., WINSTON - SALEM, S.C. 27105
PHONE: (336) 245-6400 TOLL FREE 1-800-845-9800
TECHNICAL SERVICE: 1-800-684-1199, PARTS ORDER FAX: 1-800-262-
9381CORPORATE OFFICE: WINSTON-SALEM, NC
MANUFACTURING FACILITY: BROOKVILLE, PA.
INSTALLATION AND OPERATING INSTRUCTIONS
Models: MT/RI/FC
1. Installation
a. Receiving Inspection:
Upon receipt, check all packages and accessories or optional components including legs, casters,
and shelves.
b. Legs & Casters: (optional) (See Fig. 1)
Legs screw directly into the base. Caster are plate-mounted. To install casters, tip or raise the
cabinet one side at a time and remove the four hex head screws in each corner of the bottom.
Use these same screws to attach the mounting plate. Screw-on type legs simply screw into the
adapter nut provided in each corner of the bottom. Important: Verify local sanitation codes if
unit is to be used for packaged foods.
c. Leveling: (See Fig. 2)
To provide adequate condensate drainage and proper door alignment and operation. It is necessary
that the cabinet be level. Level cabinet from front to rear and from side to side with leveling bolts,
or leg inserts. This should be done after cabinet has been set in its final operating position. The
leveling bolts are the same bolts used to attach the wood base to the cabinet. BE SURE DRAIN
HOSE IS ATTACHED TO BRACKET CONDENSATE NEXT TO EXTERIOR PAN LOCATED
BEHIND BOTTOM DISLODGED IN TRANSITGRILLE THE HOSE COULD.BE .
d. Door Handles: (See Fig 3.) Hinged Door Models
Door handles with mounting screws are packed inside each cooler.
To mount handle, lift door gasket behind two holes in front and insert screws through the holes.
Attach handle, with offset away from cabinet corner, and tighten screws.
e. Shelves:
Shipped inside each cabinet are shelves packed in plastic and a bag of shelf supports. Shelf
spacing is adjustable to suit requirements. See Instruction Sheet ILA-0904 for installing.
f. Door Removal and Adjustment:
(1) Slide Doors - Each door has its own Closing Spring located at the top and is positioned for
Proper Tension. However if adjustment is required remove doors as follows:
a. Locate Door Rollers under slot A
show in fig. 4, and lift door off track while tilting
bottom of door out.
Adjust spring by moving hook to next hole or by shortening.
If door gaskets do not seal properly follow step 1 and 2.
Step 1: Check to see if cabinet base is level.
Step 2: Adjust the Location of door Rollers in the Roller Brackets.
(2) Swing Doors - Spring tension in the bottom hinges is Factory Adjusted for adequate
“Swing Backof doors, and does not require field adjustment. For replacement parts and
instructions see enclosed instruction sheet ILA-0859.
g. Locating Cooler:
Provide at least three inches of space between cabinet and any adjacent wall or fixture, at left
end and rear of cabinet.
ILA-0931
SHEET OF 3 1
REV. D


Produkt Specifikationer

Mærke: Beverage-Air
Kategori: Køleskab
Model: LV15-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Beverage-Air LV15-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig