Black And Decker BH100 Manual

Black And Decker Boremaskine BH100

Læs gratis den danske manual til Black And Decker BH100 (2 sider) i kategorien Boremaskine. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Black And Decker BH100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

.BIACK&DECKER@

INSTRUCTIONMANUAL

HammerDrills3/8"(10mm)and112"(13mml

SAFETYINSTRUCTIONS

Warning! Whenusing electricaltools, the following basic safety pre-

cautionsshouldalwaysbetaken to reducethe risk of fire, electric

shockand personalinjury.

Readall theseinstructionsbeforeattemptingto operatethe product

and savethis booklet.

Keep areas clean. Clutteredareasand benchesinviteinjuries.work Considerthe work area environment.Donot exposethe power tool to

rain anddo not usein dampor wet locations. Keepswork areaswell

lit. Donot usethe powertool wherethere maybe a risk of fire or

explosion.

Guard against electric shock. Avoidbodycontact,where possible

with earthedor groundedsurfaces(e.g.pipes,radiators,rangesand

refrigerators).

Keep children away. Donot let visitorsshouldtouch the tool or

extensioncord. All visitors shouldbe kept awayfrom the work area.

Store idle tools. Whennot in use,tools shouldbe storedin a dry,high

or lockedplace,out of the reachof children.

Do not force the tool. It will deliverbetter performancewhentool is

usedat the recommendedspeed.

Usethe right tool. Donot force small toolsor attachmentsto do the

job of a heavy-dutytool. Donot use the tool for purposesnot intended;

for example,do not usea circularsaw to cut a tree limb or logs.

Dress properly. Donot wear looseclothingor jewelry asthey can be

caughtin movingparts. Rubberglovesand non-slqdfootwear is

recommendedwhenworking outdoors. Wearprotectivehair covering

to contain long hair.

Usesafety glasses. Use a face or dust mask as well, if the operation

is dUstyor if the tool is being usedin enclosedspaces.

Connectingdust extraction equipment. If devicesare providedfor

the connectionof dust extractionand collection,ensurethat these are

connectedand properlyused,especiallyin confinedareas.

Donot abuse the cord. Nevercarry the tool by its cord or yank it to

disconnectit from the socket. Keepthe cord awayfrom heat,oil and

sharpedges.

Secure the work. Useclampsor vicesto securelyfastenthe material

you areworking with. It is saferthan using a handand it frees both

handsto operatethe tool.

Donot overreach. Keep proper footing and balance at all times.

Maintainthe tool with care. Keepa cuttingtool sharpandcleanfor

betterand safer performance.Followthe instructionsfor lubricating

and changingaccessories.Inspectthe tools and cord periodicallyand

if damaged,haverepairedby anAuthorizedServiceCenter. Inspectthe

extensioncordperiodically,and replaceif damaged. Keepthe handles

dry,cleanandfree from 011and grease.

Disconnectthe tool. Whennot in use,beforeservicingand when

changingaccessoriessuchas blades,bits andclutters.

Remove Formthe habit of checkingto seeadjusting key wrenches.

that keysand adjustingwrenchesare removedfrom the tool and

replacedin the storageareabeforeswitching on.

Avoid unintentional starting. -Donot a plugged-intool with acarry

finger on the switch.Makesure the switch ISoff whenthe tool is plug-

ging in. .

Useanoutdoorextensioncord. Whena tool is usedoutdoors,only

use an extensioncord intendedfor outdooruse.

Stayalert. Watchwhat you are doing,usecommonsenseand do not

operatethetoolwhentired. .

Check damaged parts. Beforefurther use of the tool, guardand other

partsthat aredamagedshouldbe carefullycheckedto determine

whetherit wouldoperateproperlyand performits intendedfunction.

Checkfor alignmentof movingparts;free runningof movingparts;

breakageof parts; mountingandany otherconditionsthat may affect

itsoperation.

If the guardor other parts aredamaged,they shouldbe properly

repairedor replacedby anAuthorizedServiceCenterunlessotherwise

indicatedin the productbooklet. Havedefectiveswitchesreplacedby

anAuthorizedServiceCenter.

Donot use the tool if the switch does notturn on or off.

Warning! Theuse of anyaccessoryor attachmentotherthan recom-

mendedin the productbooklet,maypresenta risk of personalinjury.

Have The electricaltool isthe tool repaired by a qualifiedperson.

in accordancewith the relevantsafety requirements:A qualifiedper-

son usingoriginal spareparts shouldonly carry out repairs;otherwise,

this may result in considerabledangerto the user.

Savethese instructions!

FEATURES

Drillswitch(onlywith specificmodels)

Chuck

On/offswitchor variableswitch

lock-on button

Air ventilation

Belt clip

Forward/reverseswitch

control(onlywith specificmodels)

Sidehandle(onlywith specificmodels)

COMMANDS

.Theon/off switch or variablespeedswitch is usedto operateyour

drill in all modesof operation.

.Thelock-on buttonprovidescontinuousoperationof your drill.

.Ontwo speeddrills,the speedcontrolallowsselectionof the appro-

priate dnlling speed.

.Theside handle(whereprovided)givesa secondarygrippingposition

for yourdrilling speed.

.Yourdrill can operateas a hammerdrill or a rotary drill dependingon

the setting of the hammer/drillswitch.

.The forward/reverse switch controls the direction of the rotation when

yourdrill is usedas screwdriver,or whenclearingajammeddrill bit.

On/Off Switch (Fig. 1 item 3)

Toswitch you~ drill on, depress the on/off switch; your drill stops when

the switch is released.

PN: 184620-34

Lock-onButton (Fig. 1 item 4)

If continuosoperationis required,pressthe lock-onbutton while the

on/off switch ISdepressed(Fig.1 Item3).Tostop when operationis

continuos,depressthe on/off switch againand release.

Percussion Switch (Fig. 1 item 1)

This is a specialfeature in yourdrifl that allows hitting and rotatingat

the sametime.

a) Drill Mode ~

Whendrilling wood and metal.Usefulfor drilling projectsonly.

b) HammerMode I--

Whendrilling masonry,set the hammerswitch in this mode.

TwoSpeed Switch (Fig.1 item 3)

Toset the two-speedswitch in low speedpushthe switch midway

backward"I", to set the switch in high-speedpushthe switch all the

way backward"II".

OPERATIONS

1. ASA GENERALRULE. For largesizedrill bits use low speedsand

for smallerdrill bits use high speeds. Onvariablespeeddrills, the

morethe trigger is pressedthe faster the speed.

2. SETTHESPEEDOFYOURDRILL.

Set the forward/reverseswitch to the desireddirectionof rotation.

Neverchangethe setting of the hammerswitch, or the

forward/reversewhen yourdrill is in operation.

3. MAINTAINVENTSCLEAROFOBSTRUCTION.In orderto maintain

yourtool from overheating andextendthe life of your tool, maintain

the ventilationareasof yourtool free from obstructionall the time.

4. HOWTOPOSIT'')NA DRILLBIT ONYOURDRILL. Selectthe appro-

priate drill bit tor the job (fOIl

OWthe guidelinesof the table below).

First, makesure the drill ISunplugged. Holdingthe rear sectionof

the chuck,rotatethe front sectionuntil the jaws of the chuck are

sufficientlyopen.Insertthe drill bit in the jaws of the chuck.Hold

the rear sectionof the chuckwhile tighteningthe front. Turnthe

chuck key clockwiseto tighten the jaws and securelygrip the drill

bit. Usethe chuck key in the 3 holesfor better results.

) ~

L, "..

RIGHT

.L~

J(Jl

'''-'------

WRONG

5. DRILLING:Makesurethe

materialto be drilled is

tightly fastenedandwhen

dnlling thin materialsuse

a woodsupr°rt. Always

drill at a 90 angle and

place enoughpressureon

the drill for the drill to per-

foratethe surfaceyouare

drilling. Neveruseexces-

sive force when usingyour

drill.

6. ACCESSORIES:Variousaccessoriescan fit your drill, allowing you

to diversify its use. .

7. SANDINGIPOLISHING: Positionthediscasshowninthefigure

below.Placethe rubbersupportin the chuckand turn the chuckkey

)~ '

I ~~

i)~

'in.. I~1

II~-::-~

clockwisetotightenthejawsto securelyfastenthedisc.Tosetthe

polishingfeaturefollowtheexampleusingtherubberdiscandthe

spindle.

.<'-{-:\_..,-

"'~::f-j{~))er~>:;~.:!T!;t~J

.~ '-../ .,

/' ,

,I '-

'-"" '. - -1'1(~)'i,+rt$~~Y'~Y

i/"- \:'1l.. = <,':-== \~ //''' '.''''QJ..

, "D, ~~)I;;:::

. '" \"';:::-

. ., ..

\ I<!-i, ~'J

\, /,/ ..~..:\.:,"".""=

1-- jiV)§ ':' "7

, --- >1 "\'*--:f"'

~- '~

Whensanding,do not put all ~Yf,

thepressureonthefaceofthe ~~"'-. ~~-1::

disc; incline the disc at an . ... -,~~ .~

angleon the surface. WRONG" "RIGHi"'""

WRONG .J>.:<

~()

~"'" r:§.f,,/'-

...~~.

-.0= ~\

~~~"

Whilesandinguse horizontalandvertical move-

ments. Avoidcircular movements.Neversand

on edges,this maycausedamageto sand

paperas well as rubberdisc.

ACCESSORIES

The performance of any power tool dependsupon the accessory used.

Black & Decker accessories are engineeredto high quality standards and are

designed to enhancethe performance of your tool. Purchasing Black and

Decker accessories will ensurethe best performance of your Black and

Decker tool.

IQ]DOUBLEINSULATION

The tool is double insulated. This meansthat all the external metal parts are

electrically insulated from the main power supply. This is done by placing

insulation barriers between the electrical and mechanical components mak-

ing it necessaryfor the tool to be earthead (grounded).

NOTE: Double insulation does not take the place of normal safety precau-

tions when operating the tool. The insulation system is for added protection

against injury resulting from a possible electrical insulation failure within the

tool.

EXTENSIONCABLES- Upto 30m (100ft.) of 3 core extension cable can be

used with undue loss of power.

NOTE: An extension cable should not be used unless absolutely necessary.

If the use of an extension cable is a must, make sure it is properly wired,

contains the correct rated fuse as recommendedin its literature and is in

good electrical condition.

TECHNICALDATA

The level of sound pressure of the tool is in accordancewith U.L.legislation.

It is recommended that you take appropriate measuresfor the protection of

your hearing if the sound level seems uncomfortable. The normally equates

to a sound pressure in excessof 85db (A).

Black & Decker do Brasil Ltda - ROD.BR050 KM167 LO05, Parteau 1 BairroDistritoIndustrial 38056-580- UberabaMGsin II CEP-

InscriQao sob 0 n° do CNPJ: -I.E.: 701,948.711.00.98 -Industria Brasileira - Origen: Brasil53.296.273/0001-91

DRILL BIT APPLICATION

.High Speed Steel i. Steel, Aluminium, all types of

woods

. Cabide Steel . All types o,fwood

. Tungesten Carbide . Masonry, concrete, stone,

brick, tile marble, etc.

FEATURES

POWER (rpm)

Model Watts AMPS rev/min

120V 220V I III

BH50 430 3.5 1.9 2500

BH90 450" 3.7 2.0 2 500

BH100 450 3.7 2.0 2500

BH120 450 3.7 2.0 2500

BH150 450 3.7 2.0 210012500

BH200 450 3.7 2.0 0 - 2 500

BH300 500 4.0 2.2 0 - 2 500

Produkt Specifikationer

Mærke:	Black And Decker
Kategori:	Boremaskine
Model:	BH100

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker BH100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Boremaskine Black And Decker Manualer

Black And Decker REVCHD12C Manual

28 Juni 2024

Black And Decker CD18GSR Manual

30 April 2024

Black And Decker CP14LN Manual

27 April 2024

Black And Decker CD121K Manual

26 April 2024

Black And Decker 9099 Manual

18 April 2024

Black And Decker DR220 Manual

12 April 2024

Black And Decker FS632 Manual

9 April 2024

Black And Decker PF186 Manual

2 April 2024

Black And Decker BD18PS Manual

30 Marts 2024

Black And Decker TS310 Manual

30 Marts 2024

Boremaskine Manualer

Nyeste Boremaskine Manualer

Scheppach DP60 SE Manual

1 August 2025

Holzmann ZX7045PRO Manual

31 Juli 2025

Einhell TE-CD 18/40 Li BL Solo Manual

30 Juli 2025

Rothenberger RoDIADRILL 200 Manual

30 Juli 2025

Holzmann GSM16E Manual

30 Juli 2025

Eibenstock EBM 182/3 Manual

30 Juli 2025

Eibenstock ESD 162 Manual

30 Juli 2025

Eibenstock END 1550 P Manual

30 Juli 2025

Holzmann SB203V Manual

30 Juli 2025

Eibenstock END 40 A Manual

30 Juli 2025