Black And Decker HS600K Manual

Black And Decker savemaskine HS600K

Læs gratis den danske manual til Black And Decker HS600K (5 sider) i kategorien savemaskine. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Black And Decker HS600K, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

General Safety Rules

WARNING: Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Work Area

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes. Use in well ventilated areas only.

•Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

•Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in any way. Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply

system.

•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

•Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

•When operating a power tool outside, use an outdoor extension cord marked "W-A"

or "W." These cords are rated for outdoor use and reduce the risk of electric shock.

Personal Safety

•Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in serious

personal injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair

can be caught in moving parts. Air vents cover moving parts and should be avoided.

•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is

left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventative safety measures reduce

the risk of starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

•Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

Service

•Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

Specific Safety Rules

•Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the operator.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

CAUTION: Wear appropriate hearing protection during use. Under some conditions

and duration of use, noise from this product may contribute to hearing loss.

The label on your tool may include the following symbols.

V..............volts

A..............amperes

Hz............hertz

W ............watts

min ..........minutes

............alternating current

........direct current

no............no load speed

............Class II Construction

…/min......revolutions or reciprocation per minute

............earthing terminal

............safety alert symbol

INSTRUCTION MANUAL

Cat. No. HS600

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

Features - Figure A

1. Blade changing button

2. Shoe locking button

3. Shoe

4. On/off switch

5. Speed control wheel

47 8 910

Accessories - Figure B

1. Circle cutter / edge guide

2. 18tpi wavy, milled blade

3. 6tpi set, milled blade

4. 10tpi set, milled blade

5. Serrated blade

6. Round steel brush

7. Flat hook and loop holder

8. 240 grit sandpaper

9. 180 grit sandpaper

10. 120 grit sandpaper

11. Non-woven pad

12. 10tpi scroll, milled, set

13. 6tpi taper, ground

Description Function

1. Cutting circles / cutting straight lines

2. Cutting thick metal

3. Fast cutting wood

4. Plastic cutting

5. Cutting cardboard, carpet, linoleum

6. Removing rust

7. Holds tabs/ pad

8. Fine sanding

9. Medium sanding

10. Coarse sanding

11. Metal finishing

12. Scroll cutting

13. Fine finish wood cutting

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-54-HOW-TO (544-6986)

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PRODUCT,

CALL 1-800-54-HOW-TO (544-6986)

BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,

TYPE No., AND DATE CODE (e.g. 0130M). IN MOST CASES, ABLACK & DECKER REPRE-

SENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE ASUGGES-

TION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITALTO BLACK & DECKER.

* Protective sheath included

13*

diameter of the circle that you wish to cut and retighten knob. Mark the center of the circle to

be cut. Drill a hole where the blade will be positioned or cut inward from edge of material to

get blade into position. Place the point of the pivot knob into the mark in the center of the

circle. Proceed around the circle in a counterclockwise direction using light pressure on the

ZipSawTM as shown in Fig.3. Turn off tool before changing hand positions. CAUTION:

The guide arm can be mounted on either side of the shoe by removing the screw shown in

Fig. 5 and rotating the arm 180 degrees and reattaching the arm. To store circleNOTE:

cutting / edge guide in carrying case, the arm must be returned to it original position.

RIPPING

Ripping without a pencil line can easily be done with the edge guide included with your

ZipSawTM.

To use the edge guide, position the saw on a flat surface as shown in figure 4 Set the cross

bar at desired distance from blade and tighten the pivot knob. Keep the cross bar firmly

against the straight edge of the workpiece as you cut.

TOOL CARE AND MAINTENANCE

• Excessive force on the ZipSawTM will prevent the tool from operating correctly and reduce

the cutting efficiency.

• After using the ZipSawTM for extended periods on slow stroke settings, run the saw on

maximum speed for 3 minutes to aid cooling.

• Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized service centers or other qualified service

personnel, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be haz-

ardous.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations

throughout North America. All Black & Decker Service Centers are staffed with trained

personnel to provide customers with efficient and reliable power tool service. Whether you

need technical advice, repair, or genuine factory replacement parts, contact the Black &

Decker location nearest you. To find your local service location, refer to the yellow page

directory under "Tools—Electric" or call: 1-800-544-6986.

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge in

either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required. Black & Decker owned and authorized Service Centers are listed under

"Tools–Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This

product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are miss-

ing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE

LA RAISON PRIÈRE DE COMPOSER 1 800 544-6986

GUIDE D’UTILISATION

MESURES DE SÉCURITÉ

AVERTISSEMENT : Lire et comprendre toutes les directives. Le non-respect de toutes les

directives suivantes présente des risques de secousses électriques, d'incendie ou de

blessures graves.

CONSERVER CES MESURES.

ZONE DE TRAVAIL

• S'assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et

des endroits sombres présentent des risques d'accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme

celles dégagées par des liquides, des gaz ou des poussières inflammables). Les

étincelles générées par le moteur des outils électriques peuvent enflammer les poussières

ou les vapeurs.

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu'on utilise

un outil électrique. Une distraction peut entraîner la perte de maîtrise de l'outil.

MESURES DE SÉCURITÉ RELATIVES À L'ÉLECTRICITÉ

• Les outils à double isolation comportent une fiche polarisée (une lame plus large que

l'autre). La fiche n'entre que d'une façon dans une prise polarisée. Lorsque la fiche

n'entre pas à fond dans la prise, essayer de nouveau après avoir inversé les broches

de la fiche. Si la fiche n'entre toujours pas dans la prise, communiquer avec un

électricien certifié afin de faire installer une prise polarisée. Ne modifier en aucune

façon la fiche. La double isolation élimine le besoin d'un cordon trifilaire mis à la terre et

d'un système d'alimentation mis à la terre.

• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Les risques de secousses électriques sont plus

élevés si le corps de l'utilisateur est mis à la terre.

• Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration

d'eau dans l'outil augmente les risques de secousses électriques.

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter

l'outil ni tirer sur le cordon pour débrancher l'outil. Éloigner le cordon des sources de

chaleur, des flaques d'huile, des arêtes tranchantes et des pièces mobiles.

Remplacer immédiatement les cordons endommagés. Les cordons endommagés

augmentent les risques de secousses électriques.

• Lorsqu'on utilise un outil électrique à l'extérieur, se servir d'un cordon de rallonge

prévu pour l'extérieur, portant la mention "W-A" ou "W". Ces cordons sont conçus pour

servir à l'extérieur et minimisent les risques de secousses électriques.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu'on utilise un outil

électrique. Ne pas s'en servir lorsqu'on est fatigué ou affaibli par des drogues, de

l'alcool ou des médicaments. De graves blessures peuvent résulter d'un moment

d'inattention lors de l'utilisation d'un outil électrique.

• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des

bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les vêtements

et les gants des pièces en mouvement qui peuvent les happer.

• Éviter les démarrages accidentels. S'assurer que l'interrupteur est en position hors

tension avant de brancher l'outil. Afin d'éviter les risques de blessures, ne pas transporter

l'outil avec le doigt sur l'interrupteur ni brancher un outil dont l'interrupteur est en position

sous tension.

• Enlever les clés de réglage avant de mettre l'outil sous tension. Une clé qui est laissée

sur une pièce rotative de l'outil présente des risques de blessures.

• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s'assure d'une

meilleure maîtrise de l'outil dans des situations imprévues grâce à une position stable et un

bon équilibre.

S Z SCIE IP AWMC HS600

USE OF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size

extension cords with the tool – that is, proper wire size for various lengths of cord and heavy

enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in

line voltage resulting in loss of power and overheating. For proper size cords see chart

below.

MOTOR

Your Black & Decker tool is powered by a Black & Decker-built motor. Be sure your power

supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on

standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts

AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information

is printed on the nameplate. Lower voltage will cause loss of power and can result in over-

heating. All Black & Decker tools are factory-tested; if this tool does not operate, check the

power supply.

SAVE THESE INSTRUCTIONS

ASSEMBLY/ADJUSTMENT SET-UP

ON/OFF SWITCH

To turn the saw on, squeeze the trigger switch (4). To turn the tool off, release the trigger

switch. There is no provision for locking the tool on. The speed of the ZipSaw

TM is controlled

by the speed control wheel (5) which is marked with numbers from 1 through 6. Speed

increases as the wheel is turned from low speed (1) to high speed (6).

INSTALLING ACCESSORIES - FIGURE 1

BEFORE INSTALLING ACCESSORIES, TURN OFF AND UNPLUG TOOL. KEEP

PROTECTIVE SHEATH IN PLACE WHEN INSTALLING OR REMOVING ACCESSORIES.

REMOVE SHEATH TO USE.

The ZipSawTM uses a unique accessory changing system. To install an accessory, press in

on the large gray button (1) shown in Figure 1. Ensure that the shank is inserted into the

cavity of the accessory holder also shown in Figure 1. Insert the shank fully into the

accessory clamp. Release the button and the accessory will be clamped securely in place. To

release the accessory, press in on the button and pull the accessory out. NOTE: Because of

the unique design of the HS600 ZipSawTM, the accessory can be reverse mounted in the

clamp.

REMOVING THE SHOE - FIGURE 2

TURN OFF AND UNPLUG TOOL.

To remove the shoe, press in on the small black button and pull the shoe toward you as

shown in Figure 4. Shoe is removed only when using the circle and edge guideNOTE:

included.

OPERATION

CAUTION: WEAR EYE PROTECTION

GENERAL CUTTING

Be sure material is firmly secured. Hold the ZipSawTM by the handle and operate switch to

turn the unit on. Don’t attempt to turn on the unit when blade is against material to be cut. This

could stall the motor. Place front of shoe on material to be cut and hold saw shoe down firmly

against the work surface while cutting. Don’t force the tool; let the blade or other accessory

work at its own speed. Whenever possible, clamp or support work close to the line of cut;

when the cut is completed, shut off power and lay the saw aside before loosening the work.

METAL & PLASTIC CUTTING

In cutting thin gauge sheet metals, it is best to clamp wood or plywood to the bottom of the

metal sheet; this will insure a clean cut without the danger of vibration or tearing of metal. Use

a fine-tooth blade for ferrous metals (for those that have an iron content); and use a coarser

blade for nonferrous metals (those that do not have an iron content).

Cutting thin metal will take longer than cutting relatively thick wood so do not be tempted to

speed up the process by forcing the saw.

Use low speeds for cutting metals, plastics and composition tile. When cutting laminated

plastic, place the finished side down and use a fine tooth blade.

CIRCLE CUTTING

NOTE: Blade must be removed before attaching circle cutting / edge guide.

The guide arm is marked with numbers in both inches and centimeters for quick reference to

circle diameter. Loosen the pivot knob and slide it to the number that corresponds to the

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more American Wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

Produkt Specifikationer

Mærke:	Black And Decker
Kategori:	savemaskine
Model:	HS600K

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker HS600K stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

savemaskine Black And Decker Manualer

Black And Decker WM125 Manual

27 September 2024

Black And Decker RS601 Manual

15 September 2024

Black And Decker VPX1301X Manual

8 September 2024

Black And Decker KS550K Manual

6 September 2024

Black And Decker CS1004 Manual

6 September 2024

Black And Decker JS350S Manual

3 September 2024

Black And Decker VP600U Manual

1 September 2024

Black And Decker BES702 Manual

24 August 2024

Black And Decker BECS2245 Manual

20 August 2024

Black And Decker BECS1835 Manual

15 August 2024

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell GE-CS 18 Li Manual

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

14 Oktober 2024

13 Oktober 2024

Einhell TC-AP 650 E Manual

12 Oktober 2024

Einhell TE-SM 36/210 Li Solo Manual

11 Oktober 2024

Einhell BT-SM 2534 Manual

11 Oktober 2024

Hitachi C 7MFA(LA) Manual

9 Oktober 2024

Ozito ECS-406A Manual

6 Oktober 2024