Black And Decker SM600 Manual

Black And Decker savemaskine SM600

Læs gratis den danske manual til Black And Decker SM600 (60 sider) i kategorien savemaskine. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Black And Decker SM600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/60

INSTRUCTION MANUAL

16" Variable Speed Scroll Saw

with Quickset II¤Blade

Changing Feature

(Model SM600)

PART NO. 638519-00 10-30-05

ESPA OL: P GINA 21

To learn more about DELTA MACHINERY

visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,

please call 1-800-223-7278 (In Canada call 1-800-463-3582).

FRAN AIS: PAGE 41

GENERAL SAFETY RULES

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there

are certain hazards involved with the operation of the product. Using the machine with respect and caution will

considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,

personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,

goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make up

for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop. If a

procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your

personal safety is your responsibility.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not

be modified and/or used for any application other than that for which it was designed. If you have any questions relative

to a particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should

be performed on the product.

Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in

electric shock, fire and/or serious injury.

1. FOR YOUR OWN SAFETY, READ INSTRUCTION

MANUAL BEFORE OPERATING THE TOOL. Learn the

tool’s application and limitations as well as the specific

hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. ALWAYS WEAR EYE PROTECTION.

Wear safety

glasses. Everyday eyeglasses only have impact resistant

lenses; they are not safety glasses. Also use face or dust

mask if cutting operation is dusty. These safety glasses

must conform to ANSI Z87.1 requirements. NOTE:

Approved glasses have Z87 printed or stamped on them.

4. REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it “on”.

5. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t

use power tools in damp or wet locations, or expose them to

rain. Keep work area well-lighted.

7. KEEP CHILDREN AND VISITORS AWAY. All children

and visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILDPROOF – with padlocks,

master switches, or by removing starter keys.

9. DON’T FORCE TOOL. It will do the job better and be

safer at the rate for which it was designed.

10. USE RIGHT TOOL. Don’t force tool or attachment to do

a job for which it was not designed.

11. WEAR PROPER APPAREL. No loose clothing, gloves,

neckties, rings, bracelets, or other jewelry to get caught in

moving parts. Nonslip footwear is recommended. Wear

protective hair covering to contain long hair.

12. SECURE WORK. Use clamps or a vise to hold work

when practical. It’s safer than using your hand and frees

both hands to operate tool.

13. DON’T OVERREACH. Keep proper footing and

balance at all times.

14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools

sharp and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing and when

changing accessories such as blades, bits, cutters, etc.

16. USE RECOMMENDED ACCESSORIES. The use of

accessories and attachments not recommended by Delta

may cause hazards or risk of injury to persons.

17. REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in “OFF” position before plugging in

power cord.

In the event of a power failure, move switch to

the “OFF” position.

18. NEVER STAND ON TOOL. Serious injury could occur if

the tool is tipped or if the cutting tool is accidentally

contacted.

19. CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to ensure that it will operate properly and

perform its intended function – check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged should be

properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or cutter

against the direction of rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it comes to a

complete stop.

22.

STAY ALERT, WATCH WHAT YOU ARE DOING, AND

USE COMMON SENSE WHEN OPERATING A POWER

TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER

THE INFLUENCE OF DRUGS, ALCOHOL, OR

MEDICATION. A moment of inattention while operating

power tools may result in serious personal injury.

23. MAKE SURE TOOL IS DISCONNECTED FROM

POWER SUPPLY while motor is being mounted, connected

or reconnected.

24. THE DUST GENERATED by certain woods and wood

products can be injurious to your health. Always operate

machinery in well ventilated areas and provide for proper

dust removal. Use wood dust collection systems whenever

possible.

25.

WARNING: SOME DUST CREATED BY

POWER SANDING, SAWING, GRINDING, DRILLING,

AND OTHER CONSTRUCTION ACTIVITIES contains

chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals

are:

· lead from lead-based paints,

· crystalline silica from bricks and cement and other

masonry products, and

· arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work

with approved safety equipment, such as those dust

masks that are specially designed to filter out microscopic

particles.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

Produkt Specifikationer

Mærke:	Black And Decker
Kategori:	savemaskine
Model:	SM600

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker SM600 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

savemaskine Black And Decker Manualer

Black And Decker WM125 Manual

27 September 2024

Black And Decker RS601 Manual

15 September 2024

Black And Decker VPX1301X Manual

8 September 2024

Black And Decker KS550K Manual

6 September 2024

Black And Decker CS1004 Manual

6 September 2024

Black And Decker JS350S Manual

3 September 2024

Black And Decker VP600U Manual

1 September 2024

Black And Decker BES702 Manual

24 August 2024

Black And Decker BECS2245 Manual

20 August 2024

Black And Decker BECS1835 Manual

15 August 2024

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell GE-CS 18 Li Manual

15 Oktober 2024

15 Oktober 2024

15 Oktober 2024

14 Oktober 2024

13 Oktober 2024

Einhell TC-AP 650 E Manual

12 Oktober 2024

Einhell TE-SM 36/210 Li Solo Manual

11 Oktober 2024

Einhell BT-SM 2534 Manual

11 Oktober 2024

Hitachi C 7MFA(LA) Manual

9 Oktober 2024

Ozito ECS-406A Manual

6 Oktober 2024