Black And Decker WM500 Manual


Læs gratis den danske manual til Black And Decker WM500 (18 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Black And Decker WM500, eller vil du spørge andre brugere om produktet?

Side 1/18
Workmate®500
Copyright © 2004 Black & Decker Printed in China
Cat. No. WM500 Form No. B&D 588974-02, Rev. 1 (SEPT. ‘04)
588974-02,01,WM500 9/24/04 11:19 AM Page 1
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PRODUCT,
CALL .1-800-54-HOW-TO (544-6986)
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION
AVAILABLE, CATALOG NO., TYPE NO., AND DATE CODE.
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE
YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR
COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
(544-6986)
I
MPORTANT SAFETY INSTRUCTIONS
WARNING:
1. Do not load with more than 350 lbs.(160 kg) in Workmate mode and 125 lbs.(57 kg)
in Hand Cart mode.
2. Do not apply an unbalanced load which could cause the Workmate to tip over.
3. Do not step on or stand on Workmate. Do not use the Workmate as a stepladder
or standing platform.
4. Do not store Workmate outdoors or in a damp location.
5. Avoid applying excessive force when clamping with the Swivel Grips.
6. Be sure that the legs are fully opened and that the Transition Lever and Toe Plate
Slider locks in position. Secure Hand Cart loads to steel frame members as
necessary.
7. When using a power tool with the Workmate, follow the safety instructions in the
tool’s instruction manual.
8. Always wear safety glasses when operating power or hand tools.
9. An even pressure of the Vise Jaws on the workpiece is essential. Tighten both
Vise Hand Cranks uniformly.
10. Cutting or drilling into work surface may result in striking metal jaw support below,
damaging tool or work center.
11. Caution required when using high temperature tools (heat guns, torch, solder
iron, etc.). May damage work surface and reduce clamping capability.
WARNING: This product contains chemicals, including lead, known to the
State of California to cause cancer, and birth defects or other reproductive harm.
Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
NOTE! The assembly of the Workmate should take approximately 1 hour.
Before you proceed to assemble you will need the following tools.
1 - Hammer
1 - Phillips Screwdriver
1 - Nut Driver (supplied –item Oof Fig.1))
1 - Combination wrench (supplied) (not shown)
Fig. 1: Unpack
Important: Check that you have received all the parts.
Remove the contents of the carton. The following components are in the carton.
(A) 1 - Frame assembly 1 - Parts bag containing:
(B) (G)2 - Vice Screw Packing Pieces 2 - M6 x 36.5mm bolts
(installed to C)(H) 2 - M6 x 30mm bolts
(C) (I)2 - Vise Brackets 4 - M6 Locking Nuts
1
588974-02,01,WM500 9/24/04 11:19 AM Page 2


Produkt Specifikationer

Mærke: Black And Decker
Kategori: Ikke kategoriseret
Model: WM500

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker WM500 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Black And Decker Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer