Black Box LES431A Manual

Black Box Server LES431A

Læs gratis den danske manual til Black Box LES431A (2 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Black Box LES431A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com

Page 5 Page 6

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc. UL is a registered trademark of Underwriters

Laboratories. Any other trademarks mentioned in this manual are

acknowledged to be the property of the trademark owners.

Quick Start Guide

Modbus Hardened Serial Server

LES431A

Order toll-free in the U.S.:

Call 877-877-BBOX

(outside U.S. call 1-724-746-5500)

FREE technical support

24 hours a day, 7 days a week:

Call 724-746-5500 or

fax 724-746-0746

Mailing address:

Black Box Corporation

1000 Park Drive

Lawrence, PA 15055-1018

Web site: www.blackbox.com

E-mail: info@blackbox.com

Customer

Support

Information

LES431A Quick Start Guide

Step 12. Set up Port 1 ID remap.

• Only use this screen to remap “Modbus Slave IDs.”

• On each line, select the range of IDs to re-route. In

the first box, enter the first serial port of the range

to remap from. Valid port IDs range from 1 to 247.

• Second box: Enter the last serial port of the range to

remap.

• Third box: Enter starting ID of the range to remap to.

• Fourth box: Auto fills based on ranges entered in the

first three columns.

Step 13. Set up Modbus ID routing.

• Only use this screen to re-route “Modbus Slave IDs.”

• On each line, select the range of IDs to re-route. In

the first box enter the starting ID. Valid IDs range

from 1 to 247.

• Second box: Enter the last ID of the range to

re-route.

• Third box: Enter the “IP Address” or “Port” that has

slave devices attached.

• Fourth box: Shows the IP address of the slave device,

if an IP address is chosen in the third box.

Step 14. Set up Modbus priority.

• Only use this screen to set “Modbus Priority.”

• Enter up to five different priorities, based on

“Originating IP Address,” “Modbus ID,” “Modbus

Function Code,” or a combination of these.

• “IP Address” sets a static IP address for the Modbus

Hardened Serial Server.

• “Modbus ID” has a valid range from 1 to 247.

• Function code has a valid range from 1 to 99.

Step 15. Save and logout.

• If you have completed the configuration, click

“Save” to save the configuration to the serial server.

• To logout, click the “Logout” button.

Step 1. Check for all required hardware.

Your package includes:

• 1-Port Modbus Hardened Serial Server

• CD-ROM containing software

• This Quick Start Guide

You will also need:

• Network and serial cables (not included)

• Power supply (not included)

Step 2: Install the hardware.

• Connect a 10- to 48-VDC (58 VDC max.)

power supply (4.0 W required).

• Connect the network cable from the serial

server to a network drop using a standard

serial cable.

• Connect the serial device to the RS-232

DB9 or terminal block serial connector with a

straight-through cable for a DCE device or a

null-modem cable for a DTE device.

NOTE: UL® requires one conductor per terminal,

28 to 16 AWG copper-wire, tightening

torque of 5 kg-cm, and 105° C rating

sized for 60° C ampacity.

LES431A Quick Start Guide, rev. 1

LES431A Quick Start Guide

Step 16. Test and verify operation.

• The primary check for normal operation is the device

LEDs. See Step 3 in this document for more

information.

• For advanced information, see the “Modbus

Configuration Manager” menu, at the top of the

Modbus Hardened Serial Server Manager screen.

• Select “Diagnostic” to check communications status

with the Modbus Hardened Serial Server, then select

the device for which you want to check

communications data.

• A report of reply times and ping statistics is

generated and can be saved.

• Select “Monitor” to review activity logs of attached

LES431A devices, then select the device for which

logged information is needed.

• Logged information includes “Time,” “Source and

Destination,” “Type of event,” “Subscriber ID,”

“Data collected,” and “Information” the Modbus

Hardened Serial Server software has gathered since

the current login of the affected device.

Produkt Specifikationer

Mærke:	Black Box
Kategori:	Server
Model:	LES431A
Kode for international beskyttelse (IP):	IP30
Vægt:	100 g
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	10 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	-40 - 80 °C
Dimensioner (BxDxH):	81 x 119 x 30 mm
Certificering:	FCC Part 15, Class A, CE, NEMA TS2, UL Class 1, Division 2, Groups A, B, C, D
Kabelteknologi:	10/100Base-T(X)
Netværksstandarder:	IEEE 802.3
Understøttede netværksprotokoller:	TCP, IPv4, UDP, ARP, HTTP 1.0, ICMP/PING, DHCP/BOOTP, DHCP,, TCP
LED-indikatorer:	Ja
Indgangsspænding:	10 - 58 V
Understøttede Windows-operativsystemer:	Windows 7,Windows Vista,Windows XP Home,Windows XP Home x64,Windows XP Professional,Windows XP Professional x64
Strømforbrug:	4000 mA
Understøttede operativsystemer til servere:	Windows Server 2003,Windows Server 2008
Auto MDI/MDI-X:	Ja
Flowkontrol support:	Ja
Seriel grænsefladetype:	RS-232/422/485
Antal serielle porte:	1
Baud hastighed:	230400 Kbit/s
Data-bits:	5,6,7,8
RS-232 signaler:	CTS,DCD,DSR,DTR,GND,RTS,RXD,TXD
RS-422 signaler:	GND
RS-485 signaler:	Data+,Data-,GND
Stop bits:	1,1.5,2
Dataoverførselshastighed:	0.234 Mbit/s