Blaupunkt CO-S1 Manual

Blaupunkt Overvågningskamera CO-S1

Læs gratis den danske manual til Blaupunkt CO-S1 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Blaupunkt CO-S1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Wireless Carbon Monoxide Detector (CO-S1)

1. Dual Color LED Indicator (Amber & Red)

2. Learn/Test Button

Press the button to transmit a learn/test code or silence the alarm

1 x CO Detector

1 x Mounting Bracket

2 x wall plugs and screws

3 x AA 1.5V alkaline batteries

Put the Control Panel into learning mode, then press the Learn

button to transmit learn code. Refer to Control Panel manual to

complete the learning process.

MMoouunnttiinngg

Use the mounting bracket included in the package to mount the

CO detector on the wall.

1. Use the two holes on the mounting bracket as template, drill

two holes on the wall.

2. Insert wall plug if fixing into plaster or brick

3. Screw the bracket onto the wall.

4. Hook the CO detector onto the mounting bracket.

Upon CO detection, the CO Detector will raise alarm with its

built-in siren and send alarm signal to Control Panel in different

time length according to the CO concentration level detected.

Please see following table for reference.

Once the CO Detector has activated the alarm, it will continue to

resend the alarm signal every 10 minutes until the CO

concentration level drops below 30 ppm. The CO Detector will

then send a restoration signal and stop the alarm. You can also

press the learn/test button to silence the alarm manually. The CO

Detector will then enter Alarm Silence mode.

Alarm Silence

When the alarm is activated, pressing the learn/test button will

put the CO Detector into Alarm Silence mode for 10 minutes.

During this period, the built-in siren will be silenced and the

Amber LED will flash once per second.

After the 10-minute period is over, the CO Detector will check the

CO concentration again. If the CO concentration is still over

alarm threshold, the CO Detector will sound the alarm and

transmit alarm signal again. If not, it returns to normal operation.

The CO detector uses three AA 1.5V alkaline batteries as its

power source. It features low battery detection function to notify

the Control Panel when battery voltage is low.

Follow the procedure below to change the batteries.

1. Loosen the screw on the back to open battery compartment

cover.

2. Remove the old batteries.

3. Press the learn/test button several times to fully discharge.

4. Insert the new batteries observing correct polarity. The CO

detector will sound 2 short beeps, RED LED will flash once

5. Replace the battery cover and tighten the screw.

Off Normal Operation

Amber LED flashes

every 30 seconds

Low Battery

Amber LED flashes

quickly

CO Sensor fault

Red LED flash CO Detector is alarming

Red LED on CO Detector is transmitting signal

-10°C to 40°C, relative humidity 85% non-condensing.

433 MHz

CO concentration

level

Time taken before

alarming

30 ppm None

50 ppm 60~90 minutes

100 ppm 10~40 minutes

300 ppm Under 3 minutes

Mounting

Holes

Mounting Bracket

Produkt Specifikationer

Mærke:	Blaupunkt
Kategori:	Overvågningskamera
Model:	CO-S1
Produktfarve:	Hvid
Relativ luftfugtighed ved drift (H-H):	0 - 85 %
Driftstemperatur (T-T):	-10 - 40 °C
Antal:	1
Dimensioner (BxDxH):	130 x 100 x 41 mm
Forbindelsesteknologi:	Trådløs