Blaupunkt IR-S1L Manual

Blaupunkt Overvågningskamera IR-S1L

Læs gratis den danske manual til Blaupunkt IR-S1L (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 66 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 33.5 anmeldelser. Har du et spørgsmål om Blaupunkt IR-S1L, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Wireless - P- Pet Immune PIR Motion Sensor (IR S1L)

1. Learn/Test Button LED indicator&

Press the button to transmit a learn/test code and enter Test

mode for 3 minutes. The LED will light up whenever a movement

is detected under Test mode.

2. Battery Insulator

3. Supervision Enable/Disable Jumper Switch

(JP2)

4 . High/Low S umper Switch (JPensitivity J 3)

5. Tamper Switch

The Tamper switch protects the unauthorized cover PIR from

opening.

1 x PIR Sensor

4 x wall plugs and screws

1 y - x 3V lithium batter (pre installed)

Supervision Enable/Disable Jumper Switch (JP2)

If enabled, the PIR sensor will transmit supervision signal to

Control Panel periodically for the sensor to monitor PIR sensor

condition.

Jumper set to ON = supervision function is Disabled

Jumper set to OFF = supervision function is Enabled (Default)

High/Low Sensitivity Jumper Switch (JP3)

Jumper set to ON = PIR sensitivity is set to High (Default)

Jumper set to OFF= PIR sensitivity is set to Low

Put the Control Panel into learning mode, then press the learn

button to transmit learn code. Please refer to Control Panel

manual for to complete the learning process.

The PIR Sensor has knockouts on the back where plastic is

thinner. The 2 center knockouts are for flat wall mounting, and the

4 side knockouts are for corner mounting Mount the PIR Sensor .

at 1.9m to 2m height for optimal performance.

1. Break through the knockouts; use the knockouts to mark

position on the wall or corner.

2. Drill holes into the wall or corner using the knockouts as

template.

3. Fix the PIR Sensor base onto the wall with the screws and

plugs provided.

4. Replace the PIR Sensor cover onto the base.

The PIR ” of approxifeatures a “sleep time mately 1 minute for

power conservation . After transmitting a detected movement, the

PIR will not retransmit for 1 minute. Any further movement

detected during this sleep period will extend the sleep time by

another minute. In this way continuous movement in front of a

PIR will not unduly exhaust the battery.

Press the Test Button to enter Test mode for 3 minutes. Sleep

timer will be disabled under Test mode, and the LED indicator will

flash every time a movement is detected. Use the Test mode to

determine PIR detection coverage and plan the installation

location accordingly.

LLEEDD IInnddiiccaattoorr

Off

Normal Operation

On (2 seconds)

- When Tamper Switch is triggered

- Movement detection under low battery,

tamper triggered, or Test mode.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

parked on one pin.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

parked on one pin.

Surface Fixing

Knockouts x 2

(Inside)

Corner Fixing

Knockouts x 4

Produkt Specifikationer

Mærke:	Blaupunkt
Kategori:	Overvågningskamera
Model:	IR-S1L
Produktfarve:	Hvid
Relativ luftfugtighed ved drift (H-H):	0 - 85 %
Driftstemperatur (T-T):	-10 - 40 °C
Antal:	1
Dimensioner (BxDxH):	87.7 x 66.4 x 47.7 mm
Forbindelsesteknologi:	Trådløs
Betragtningsvinkel:	110 °
Sensor afstand:	200 m