Blaze BLZ-PROIR Manual

Blaze Grill BLZ-PROIR

Læs gratis den danske manual til Blaze BLZ-PROIR (3 sider) i kategorien Grill. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Blaze BLZ-PROIR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CALIFORNIA PROPOSITION 65 WARNING

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

which are known to the State of California to cause cancer and birth defects or other reproductive harm.

For more information go to: www.P65Warnings.ca.gov

How to Replace a Conventional Burner with an Infrared Sear Burner

1. To install the optional infrared burner, begin by first removing the far left cooking grid, flame

stabilizing g izing grid will not be re installed over the burner. rid and heat zone divider. The Flame stabil -

2. Remove the conventional burner by removing the cotter pin that holds it in place. The pin is located

on the bottom rear of the burner and is accessible from the outside rear of the grill. Use needle nose

plyers to remove the cotter pin. Once removed, remove the conventional burner.

3. Remove the crossfire panel. The crossfire panel is a downward U shaped channel located between the

burners towards the rear of the burners. The y unscrewing the fastener crossfire panel is removed b

under the channel which holds it in place. The most commonly used fastener can be removed with a

metric #4 Allen wrench included with the sear burner.

4. Install the infrared burner into the grill in the same way that the conventional burner installed with

the male post on the rear of the burner resting in the opening in the grill and the chassis cylindrical

venture tube installing around the valve stem in the front. Note: IT IS CRITICAL THAT THE FRONT END OF

THE INFRARED BURNER IS INSTALLED APPROPRIATELY ONTO THE GAS VALVE TO ENSURE THE GAS

FLOWS SAFELY INTO THE BURNER.

Depending on which series of grill, the included spacer might be needed to allow the burner to mount

into the grill body securely. (See figure below)

This is recognized by the burner not completely lowering into place where the male post seats at the

opening in the grill chassis. If so, place the spacer n as show below and install the.

5. With either of the above configurations, replace the cotter pin to hold the burner firmly in place.

6. Replace the heat zone divider and cooking grid BUT NOT THE FLAME STABALIZING GRID.

7. Burn off your sear burner on high before the first use. It is normal to see it smoke as it burns off the

oils from manufacturing. Your burner will also discolor and the mesh plate on top will also flex slightly in

certain areas. Burn off until it is finished smoking (roughly 5 minutes).

For additional information, 9510 or go to Blaze contact your dealer or Blaze - -at 866 976 grills.com.

Produkt Specifikationer

Mærke:	Blaze
Kategori:	Grill
Model:	BLZ-PROIR

Har du brug for hjælp?

Hvis du har brug for hjælp til Blaze BLZ-PROIR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Grill Blaze Manualer

Blaze BLZ5LP Manual

29 December 2024

Blaze BLZ4NG Manual

29 December 2024

Blaze BLZ-GRIDDLEIJ Manual

16 August 2024

Blaze BLZ-36-VHOOD Manual

15 August 2024

Blaze BLZ-4 Manual

15 August 2024

Blaze BLZ-GP10 Manual

15 August 2024

Blaze BLZ-3 Manual

14 August 2024

Blaze BLZ-GP12 Manual

13 August 2024

Blaze BLZ-PBLTELP Manual

13 August 2024

Blaze BLZ-GP11 Manual

12 August 2024

Grill Manualer

Nyeste Grill Manualer

Kamado Joe Classic Joe II Manual

9 April 2025

Twin Eagles TEBQ42RS Manual

1 April 2025

Weber Genesis E-435 Manual

1 April 2025

Weber Genesis S-435 Manual

1 April 2025

DCS ADN1-20X36 Manual

29 Marts 2025

Weber Genesis E-335 Manual

27 Marts 2025

Beefmaster V Series G2BEEFG Manual

27 Februar 2025

DCS GDE1-30-L Manual

21 Februar 2025

DCS BGC30-BQ-N Manual

21 Februar 2025

BeefEater Discovery BD77032 Manual

11 Februar 2025