Bompani BOCA080/E Manual

Bompani Vaskemaskine BOCA080/E

Læs gratis den danske manual til Bompani BOCA080/E (4 sider) i kategorien Vaskemaskine. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Bompani BOCA080/E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

5019 612 10243

Programme

Care

Labels

Max.

Load

Type of wash / Notes

- for temperature selection, respect the manufacturer's recommendations on the care label

Detergents and Additives Special options Max.

Spin

Speed

rpm

Pre-

wash

Main

Wash

Softener Rinse

hold

Pre-

wash

Rapid Variable

spin

Cotton

40 - 60 - 95 °C

40 - 60 - 95°C

5.0

Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of

cotton and linen.

For washing heavily soiled laundry, the “Prewash” option can be selected.

Yes

i i i i

max.

Synthetics

30 - 40 - 60 °C

30 - 40 - 60°C

3.0

Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide

(Perlon, Nylon).

Yes

i i i i i

max.

Delicates

30 - 40 °C

30 - 40°C

1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses.

Yes

i i i

–

max.

Daily load

40 °C

40°C

3.0 Slightly to normally soiled textiles made of cotton and/or synthetics. – Yes

i i

– –

max.

Quick wash 15´

30 °C

30°C

3.0

Refreshed briefly worn outer clothing made of cotton, artificial fibers and blends with cotton.

Use lowest recommended detergent amount.

– Yes

i i

– –

max.

Wool

Cold - 40 °C

- 40°C

1.0

Only woollens with a felt-free finish, labelled with the woolmark and identified as machine

washable.

– Yes

i i

– –

max.

Handwash

30 - 40 °C

30 - 40°C

1.0 Textiles made of linen, silk, wool and viscose marked as “handwashable”. – Yes

i i

– –

400

Rinse & Spin – 5.0 Same as the last rinse and the final spin in the “Cotton” programme. – –

i i

– –

max.

Spin – 5.0 In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme. – – – – – –

max.

Gentle Spin – 1.0 – – – – – –In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.

max.

Drain – – – – – – – – – –Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”.

A. Programme selector

B. Programme sequence indicator

C. “Variable spin” button

D. “Start/Pause” button

E. “Reset” button

F. “Door open” indication

This washing machine is equipped with

automatic safety functions which detect and

diagnose faults at an early stage and react

appropriately:

G. “Service” indication

H. “Water tap closed” indication

I. “Clean pump” indication

Do not use liquid detergent for main wash if you

have activated prewash option.

For improved garment care, spin speed is restricted

to 400 rpm in this programme.

Selectable for programmes Cotton 60 and 40°C only.

PROGRAMME CHART

N.B. This machine is controlled by sensors. Please avoid excessive detergent dosing.

i: optional / Yes : dosing required

5019 612 10243

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

without “Rapid”

(kWh)

Approx. Programme Duration (hrs : min)

without “Rapid” with “Rapid”

Cotton 95 5.0 50* 1.70 2:05 –

Cotton** 60 5.0 47 0.89 2:45 2:10

Cotton** 60 2.5 32 0.68 2:10 ***

Cotton 40 5.0 47 0.65 2:00 1:45

Cotton** 40 2.5 32 0.52 1:45 ***

Synthetics 60 3.0 50* 0.90 2:05 1:14

Synthetics 40 3.0 40 0.50 1:50 0:59

Delicates 40 1.5 50 0.55 0:45 –

Daily load 40 3.0 40 0.45 1:00 –

Quick wash 15´ 30 3.0 30 0.15 0:15 –

Wool 40 1.0 55 0.55 0:45 –

Handwash 40 1.0 40 0.40 0:35 –

CONSUMPTION DATA

1. Load the machine, close the drum doors and check

that they are properly locked.

2. Add detergent and additives into the dispenser to

no more than the level mark, as follows:“MAX”

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Stain remover agents

• Anti-scale agents (if necessary)

3. Close the lid.

4. Turn the to the desiredprogramme selector

programme and temperature. The lamp next to the

“Start/Pause” button flashes. The indication lamp

of the predefined spin speed lights up.

PREPARATION OF THE WASH CYCLE

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a

wash programme is running, the lid remains locked and

must on no account be forced open. In case you have

an urgent need to open it during a running programme,

refer to “Cancel (Reset) a running programme before

the end”.

PROGRAMME START

Open the tap and press the “Start/Pause” button.

The indication lamp next to the “Start/Pause” button

lights up. The programme sequence indicator shows

the current programme phase, running from left to right

through Wash, Rinse, Spin/Drain. When the programme

phrase is finised, the corresponding indication goes out.

• Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

PROGRAMME END

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open for some time to allow the

interior of the machine to dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start/Pause” button to pause the

programme. The light flashes.

2. Select the new programme, any options and another

spin speed if you want.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where

the previous programme was interrupted. Do not

add detergent for this programme.

CANCEL (RESET) A RUNNING PROGRAMME

BEFORE THE END

The button cancels a programme before the “Reset”

end. Press the “Reset” button for at least 3 seconds.

Any existing water is drained out before the door can be

opened.

SELECT THE DESIRED OPTION(S)

Selecting or deselecting an option can be done at

any time during the programme. The option will be

applied as long as the corresponding programme

phase has not been executed yet.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing

and prevent colours from changing.

• This option is particularly recommended for the

“Synthetics”, “Daily load” and “Delicates”

programmes.

• It is useful if you want to postpone spinning to a later

time, or if you want to drain out only.

• If you select “Rinse Hold”, do not leave items to

soak for too long.

• As soon as the appliance stops in the rinse hold, the

“Rinse hold” lamp of the sequence indicator lights up

and the lamp next to the “Start/Pause” button flashes.

Terminate the “Rinse hold” option:

• Press the “Start/Pause” button; the programme

will terminate automatically with the final spin cycle

for the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain”

programme and press the “Start/Pause” button.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt). Increases the cycle time by

approximately 20 min.

“Rapid” button

• Enables quicker washing by shortening the

programme duration.

• Recommendable for small loads or only lightly soiled

laundry.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

the rinse. The water is drained out only.

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer

to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).