Bosch 1375A Manual

Bosch Kværn 1375A

Læs gratis den danske manual til Bosch 1375A (32 sider) i kategorien Kværn. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Bosch 1375A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/32

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1375-01

1375A

1375AK

For English Parlez-vous français? ¿Habla español?

See page 2 Voir page 12 Ver página 22

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free

for Consumer Information

& Service Locations

Pour renseignement des

consommateurs et centres

de service, appelez au

numéro gratuit :

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

BM 1619P01046 5-05 5/10/05 10:39 PM Page 1

Read and understand all instructions. Failure to follow all instructions

listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

-2-

Work Area

Keep your work area clean and well lit.

Cluttered benches and dark areas invite

accidents.

Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust

or fumes.

Keep by-standers, children, and visitors

away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with a

polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet

only one way. If the plug does not fit fully in

the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to

install a polarized outlet. Do not change the

plug in any way. Double Insulation

eliminates the need for the three wire grounded

power cord and grounded power supply

system.

Before plugging in the tool, be certain

the outlet voltage supplied is within the voltage

marked on the nameplate. Do not use “AC

only” rated tools with a DC power supply.

Avoid body contact with grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk

of electric shock if your body is grounded. If

operating the power tool in damp locations is

unavoidable, a Ground Fault Circuit Interrupter

must be used to supply the power to your tool.

Electrician’s rubber gloves and footwear will

further enhance your personal safety.

Don't expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord

to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp

edges or moving parts. Replace damaged

cords immediately. Damaged cords increase

the risk of electric shock.

When operating a power tool outside, use

an outdoor extension cord marked "W-A"

or "W." These cords are rated for outdoor use

and reduce the risk of electric shock. Refer to

“Recommended sizes of Extension Cords” in

the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

Dress properly. Do not wear loose clothing

or jewelry. Contain long hair. Keep your

hair, clothing, and gloves away from

moving parts. Loose clothes, jewelry, or long

hair can be caught in moving parts. Keep

handles dry, clean and free from oil and

grease.

Avoid accidental starting. Be sure switch is

“OFF” before plugging in. Carrying tools with

your finger on the switch or plugging in tools

that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before

turning the tool “ON”. A wrench or a key that

is left attached to a rotating part of the tool may

result in personal injury.

Do not overreach. Keep proper footing and

balance at all times. Proper footing and

balance enables better control of the tool in

unexpected situations.

Use safety equipment. Always wear eye

protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used

for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to

secure and support the workpiece to a

stable platform. Holding the work by hand or

against your body is unstable and may lead to

loss of control.

WARNING

Power Tool Safety Rules

BM 1619P01046 5-05 5/10/05 10:39 PM Page 2

Produkt Specifikationer

Mærke:	Bosch
Kategori:	Kværn
Model:	1375A
Vekselstrømsindgangsspænding:	120 V
Vekselstrømsindgangsfrekvens:	60 Hz
Vægt:	1700 g
Produktfarve:	Black,Turquoise
Indgangseffekt:	680 W
Strømkilde:	Vekselstrøm
Tomgang (maks.):	11000 rpm
Soft greb:	Ja
Længde:	266.7 mm
Slibeskive, diameter:	115 mm
Antal slibediske:	1