Boss B65LED Manual


Læs gratis den danske manual til Boss B65LED (4 sider) i kategorien Bil højttaler. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Boss B65LED, eller vil du spørge andre brugere om produktet?

Side 1/4
B65LED
Installation Instructions
300 Watts / 6.5” (165 mm)
3-Way Full Range Speakers (1 Pair)
Thank you for purchasing a BOSS Audio Systems product. Please read through these
instructions carefully so you will know how to install this product properly.
Package Contents
2x Speakers with grilles
2x Speaker wires with polarity connectors
8x Mounting screws and clip nuts
Installation Instructions/ Cut-out Template/
Warranty
Specications
3-way full range system
Woofer: 6.5” (165 mm)
polypropylene cone, rubber surround
Midrange: 1” (25 mm)
Tweeter: 0.5(13 mm)
Output power: max 300 W
Nominal impedance: 4 Ω
Frequency response: 75 Hz – 20 kHz
Sensitivity: 87 dB (1 watt/1 meter)
LED Power supply: 12 V/DC
LED current consumption: 20 mA
Speaker dimensions
A
B
A. Overall diameter: 6.61” (168 mm)
B. Mounting hole diameter: 5.59” / (142 mm)
C. Mounting depth: 2.13” (54 mm)
D. Grill protrusion: 0.79” (20 mm)
E. Overall speaker with grill: 6.89” (175 mm)
F. Tweeter protrusion: 0.5” (13 mm)
G. Outer motor diameter: 3.15” (80 mm)
C
D
E
F
G
- 1 -
Installation Precautions
Consult an expert when in doubt about installation. Professional installation is always recommended.
Prior to installation, disconnect the negative terminal of the vehicle battery.
Connect the LED lighting to 12V power supply only. Do not connect to 24V power supply.
When installing the speakers, take into consideration the risks that can arise from devices being torn
away in the case of an accident. Therefore, make sure the speakers are rmly secured and the mounting
area is sufciently stable.
Avoid routing wires near any sharp or moving parts. Run wires away from other wires that may cause
unwanted noise. Insulate bare wires properly.
If you must modify the vehicle for the speaker installation, make sure you do not impair the safety and
structural integrity of the vehicle.
Before you drill or cut any holes, investigate your vehicle’s layout very carefully. Take special care when
you work near the fuel tank, fuel lines, hydraulic lines and electrical wiring.
Mounting
You can t the speakers in the factory speaker openings in a vehicle, or create a cutout in a vehicle for
speaker installation.
Option 1: Mounting in the factory speaker location
1. Make sure the factory speaker opening (e.g. in the door or kick panel) ts the speaker in size.
2. Remove the panel which hides the factory speaker locations, and then remove the old speaker.
3. Connect the speaker to the factory speaker wiring with correct polarity. If factory speaker wiring is
corroded, use supplied speaker wires.
4. Fasten the speaker into the factory opening with the supplied screws. Some vehicles may require a
speaker mounting adapter.
Make sure the speaker sits ush across the entire mounting surface.
Make sure the newly installed speaker does not interfere with any operations (e.g. windows rolling all the
way down if in a door, or trunk mechanism if in the rear deck, etc.)
5. Perform a quick test, then reinstall the panel. Be sure to properly break in speakers and not reach max
volume until after two 20-minute cycles at regular volume.
- 2 -


Produkt Specifikationer

Mærke: Boss
Kategori: Bil højttaler
Model: B65LED

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss B65LED stil et spørgsmål nedenfor, og andre brugere vil svare dig




Bil højttaler Boss Manualer

Boss

Boss NX694 Manual

1 September 2024
Boss

Boss B65LED Manual

30 August 2024
Boss

Boss P55.4C Manual

19 August 2024
Boss

Boss P65.4C Manual

15 August 2024
Boss

Boss BE423 Manual

14 August 2024
Boss

Boss PC65.2C Manual

14 August 2024
Boss

Boss BE524 Manual

14 August 2024
Boss

Boss ASK904B.64 Manual

14 August 2024

Bil højttaler Manualer

Nyeste Bil højttaler Manualer