Boss Power Stack ST-2 Manual

Boss Guitar forstærker Power Stack ST-2

Læs gratis den danske manual til Boss Power Stack ST-2 (1 sider) i kategorien Guitar forstærker. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Boss Power Stack ST-2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
Owner’s Manual
Use of Battery
5 A battery was installed in the unit before it left the factory. The life
of this battery may be limited, however, since its primary purpose
was to enable testing.
5 If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (supplied on a separate sheet).
5 When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
5 Batteries should always be installed or replaced before connecting
any other devices. This way, you can prevent malfunction and
damage.
5 The use of an AC adaptor is recommended as the unit’s power
consumption is relatively high. Should you prefer to use batteries,
please use the alkaline type.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
Main Features
7This is a distortion eect that produces the powerful sound of a large amp stack.
7It can generate a wide variety of distortion, ranging from classic rock sounds to modern high-gain sounds.
7You can obtain richly expressive guitar sounds by varying your guitar’s volume and your picking dynamics.
DC IN jack
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without
being concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the correct
voltage. Do not use any other AC adaptor, since this may cause malfunction.
* If the AC adaptor is connected while power is on, the power supply is drawn from the AC adaptor.
* We recommend that you keep batteries installed in the unit even though you’ll be powering it with
the AC adaptor. That way, you’ll be able to continue a performance even if
the cord of the AC adaptor gets accidently disconnected from the unit.
Electric Guitar
Guitar Amplier
LEVEL knob
Adjusts the volume when the eect is on.
BASS knob
Adjusts the tone quality of the lower range when the eect is on.
OUTPUT jack
Connect this jack to your amp or to the input of another eect unit.
Pedal switch
This switch turns the eect on/o.
Thumbscrew
When this screw is loosened, the pedal will
open, allowing you to change the battery.
* For instructions on changing the
battery, refer to “Changing the Battery.”
CHECK indicator
This indicator shows whether the eect is on or o, and also doubles as the battery check
indicator. The indicator lights when the eect is on.
* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t
light at all—when you try to turn the eect on, the battery is near depletion and should
be replaced. For instructions on changing the battery, refer to “Changing the Battery.”
SOUND knob
Adjusts the sound character of the distortion and the amount of distortion
obtained when the eect is turned on.
Ultra-high-gain distortion.
Distortion that packs a great punch.
Fat crunch sound.
TREBLE knob
Adjusts the tone quality of the upper range when the eect is on.
INPUT jack
This jack accepts signals coming from a guitar or other musical instrument, or
another eects unit.
* The INPUT jack doubles as the power switch. Power to the unit is turned on
when you plug into the INPUT jack; the power is turned o when the cable
is unplugged. To prevent unnecessary battery consumption, be sure to
disconnect the plug from the INPUT jack when not using the eects unit.
Panel Descriptions
AC Adaptor
(PSA series: optional)
Precautions When Connecting
5 To prevent malfunction and equipment failure, always turn
down the volume, and turn o all the units before making any
connections.
5 Do not use connection cables that contain a built-in resistor.
5 Raise the amp volume only after turning on the power to all
connected devices.
5 Once the connections have been completed, turn on power to
your various devices in the order specied. By turning on devices
in the wrong order, you risk causing malfunction and/or damage
to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
5 This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
Changing the Battery
1. Hold down the pedal and loosen the thumbscrew, then
open the pedal upward.
* The pedal can be opened without detaching the thumbscrew
completely.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
2. Remove the old battery from the battery housing, and
remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil
spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Specications
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output
Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance 10 kΩ or greater
Power Supply Alkaline battery (9 V, 6LR61)
AC adaptor (PSA series: sold separately)
Current Draw 65 mA
* Expected battery life under continuous use:
Alkaline: 5.5 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 410 g / 15 oz (including battery)
Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT
NOTES,” and “Information”)
Alkaline battery (9 V, 6LR61)
Options
(sold separately) AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
© 2010 Roland Corporation 02
English

Produkt Specifikationer

Mærke: Boss
Kategori: Guitar forstærker
Model: Power Stack ST-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Boss Power Stack ST-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Guitar forstærker Boss Manualer

Boss

Boss KATANA ARTIST GEN 3 Manual

15 Februar 2025
Boss

Boss KATANA-MINI X Manual

8 Januar 2025
Boss

Boss KATANA-Mini Manual

16 December 2024
Boss

Boss KATANA-HEAD MkII Manual

16 December 2024
Boss

Boss KATANA-AIR Manual

16 December 2024
Boss

Boss KATANA-100/212 MkII Manual

16 December 2024
Boss

Boss KATANA-50 MkII Manual

16 December 2024
Boss

Boss Chorus Ensemble CE-5 Manual

16 December 2024
Boss

Boss Mega Distortion MD-2 Manual

16 December 2024
Boss

Boss Bass Driver BB-1X Manual

16 December 2024

Guitar forstærker Manualer

Nyeste Guitar forstærker Manualer

Blackstar

Blackstar HT-5RH MK III Manual

7 Februar 2025
VOX

VOX Brian May MV50 Manual

7 Februar 2025
NUX

NUX Mighty Plug Pro MP-3 Manual

1 Februar 2025
Marshall

Marshall JVM410H Manual

11 Januar 2025
Blackstar

Blackstar CabRig Manual

9 Januar 2025
Blackstar

Blackstar ID:CORE Stereo 10 V4 Manual

9 Januar 2025
Hartke

Hartke HD50 Manual

29 December 2024
Mooer

Mooer Envelope Manual

29 December 2024
Mooer

Mooer Liquid Manual

29 December 2024
Orange

Orange Terror Bass Manual

27 December 2024