Britax Kid II Manual

Britax Bilsæde Kid II

Læs gratis den danske manual til Britax Kid II (2 sider) i kategorien Bilsæde. Denne vejledning er vurderet som hjælpsom af 94 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 47.5 anmeldelser. Har du et spørgsmål om Britax Kid II, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Belt guide (bright red)

01 Headrest

Seat cushion

Belt holder Compartment for user manual

05 Backrest

Headrest adjustment handle

2. INTRODUCTION

Thank you for choosing

KID II

to keep your child safe through a new stage of

their life.

In order to protect your child correctly, the

KID II

must always be used

and installed as described in these instructions.

If you have any further questions regarding its use, please feel free to contact

us:

These instructions use the following symbols stated below:

Symbol Keyword Explanation

DANGER! Risk of severe personal injury

WARNING! Risk of minor personal injury

CAUTION! Risk of material damage

TIP: Useful notes

Instructions that follow a set sequence are numbered.

Example:

1. Press the button...

Belt guide colours

For better differentiation, the two vehicle seat

belts are highlighted in different colours. The di-

agonal seat belt 18 in dark red and the lap belt

17 in bright red. The colour of the belt guides

on the child safety seat follows the same colour

scheme.

4. USE IN THE VEHICLE

Please observe the instructions for using children's restraining systems in the operating

instructions of your vehicle. 3-point beltThe seat can be used in vehicles with a .

Please nd the information on the seats approved for child safety seats of the weight classes 15

to 36 kg operating instructions of your vehicle in the .

The is approved for one method of installation:KID II

Symbol Installation type Approval type

with the vehicle's 3-point seatbelt universal

You can use your child safety seat as follows:

In the direction of travel yes

against the direction of travel no

with 2-point belt no

with 3-point belt2) yes

on front passenger seat yes

on outer rear seat yes

on centre rear seat (with

3-point belt) yes 4)

1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only if the

vehicle seat is also approved for use by adults. The seat may not be in the area of effect of

an airbag.

2) The safety belt must be approved to ECE R 16 or a comparable standard (see test label on

belt with an "E" or "e" in a circle).

3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions

in vehicle owner's manual.

4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.

15–36 kg

3. Certification

BRITAX RÖMER

Child safety seat

Testing and certication

In accordance with ECE* R 44/04

Group Body weight

KID II

II+III 15 to 36 kg

*ECE = European Standard for Child Safety Equipment

The child safety seat has been designed, tested and certied according

to the requirements of the European Standard for Child Safety Equipment

(ECE R 44/03). The seal of approval E (in a circle) and the approval number

are located on the orange approval label (sticker on the child safety seat).

DANGER! This approval will be invalidated if you make any modica-

tions to the child safety seat. Only the manufacturer is permit-

ted to make modications to the child safety seat.

WARNING! Use the

KID II

exclusively for securing your child in your

vehicle. It is in no way suitable as a seat or toy in the home.

Never secure your child or the child safety seat with a 2-point DANGER!

belt. If you secure your child in the child seat with only a

2-point belt, then in the event of an accident this may cause

serious injuries to your child, possibly resulting in death.

PAGE I

6. DISASSEMBLY AND DISPOSAL

1. PRODUCT OVERVIEW

1. Operate the release button of your vehicle seat

buckle.

2. Pull out the diagonal belt 18 from the dark red belt

holder 02 on the headrest 05 .

The child safety seat can now be removed.

the child safety seat must always be DANGER!

secured when it is in the vehicle, even if no child is

being transported.

DISPOSAL:

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, thermal utilisation

Plastic parts According to the labelling in the corre-

sponding container

Metal parts Container for metals

Belt straps Container for polyester

buckle and tongue Residual waste

REMOVAL:

UNFASTENING YOUR CHILD:

1. To unfasten your child, use the release button of your vehicle seat buckle.

Removing the seat cover

1. Moving the headrest of the vehicle seat into the top

position.

2. Unhook the cover hooks 20 on the rear of the back-

rest 07 .

3. Remove the upper part of the cover.

4. Unhook the cover loops 21 at the bottom on the rear

of the backrest 07

5. Pull off the cover from the seat cushion 03 .

Removing the headrest cover

Unhook the cover loops

on the back of the head-

rest

7. Unhook the cover hooks 20 on the front of the back-

rest 07 .

Pull off the cover of the headrest

►The cover can now be washed.

Please observe the

instructions on the washing label of the cover:

Re-tting the cover

Proceed in reverse order to put on the cover.

5. CARE AND MAINTENANCE

Please ensure that you only use the original BRITAX RÖMER replacement seat

covers, as the seat cover is an integral part of the child safety seat and fulls

important functions to ensure the smooth operation of the system. Replacement

seat covers are available from your dealer or from an ADAC ofce.

• The cover can be removed and washed with a mild detergent in the delicates

programme of the washing machine (30 °C). Please observe the instructions

on the washing label of the cover.

• The plastic parts can be cleaned using soapy water. Do not use any caustic

cleaning agents (such as solvents).

DANGER! The child seat must not be used without the seat cover.

15 to 36 kg

(~4 to 12 years of age)

www.britax.eu

2000010059 14/12

User instructions

KID II

141210_KID_II_GB.indd 1 10.12.2014 11:00:17

7. SAFETY NOTES

Please take the time to read these instructions carefully and keep

them to hand in the intended storage compartment 04 on the child

safety seat at all times! The instructions must be with the child safety

seat if the latter is passed on to a third party.

DANGER! For the protection of your child:

• In the event of an accident with a collision speed of more than 10 km/h,

the child safety seat may be damaged without the damage becoming

immediately visible. In this case the child safety seat must be replaced.

Please dispose of it properly.

• As a rule, have your child safety seat checked if it was damaged (e.g if it

falls on the ground).

• Regularly check all important parts for damage. Ensure that all mechanical

parts, in particular, are fully functional.

• Never lubricate or oil parts of the child seat.

•

Never leave your child unattended in the child seat in the vehicle.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Protect the child safety seat from intensive direct sunlight when it is not in

use. The child safety seat can get very hot in direct sunshine. Child skin is

sensitive and could thereby be harmed.

•

The more snugly the belt ts over your child's body, the better they will be pro-

tected. Therefore avoid putting thick clothes on your child under the belt.

• Take regular breaks on long journeys in order to give your child the oppor-

tunity to play around.

• Use on the rear seat: Move the front seat forward far enough that you

child's feet cannot hit the backrest of the front seat (to prevent risk of

injury).

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or an accident, unsecured persons or

objects may cause injury to other vehicle occupants. Please always check

that...

• the backrests of the vehicle seats are locked (i.e. that any foldable rear

seat bench latch is engaged).

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf)

are secured.

• all persons in the vehicle have their seatbelts fastened.

• the child safety seat is always secured when it is in the vehicle, even if no

child is being transported.

WARNING! For your protection when handling the child seat:

• Never use the child safety seat free-standing, not even for test sitting.

• When swivelling up the backrest 07 , nothing must come between the

backrest 07 and the seat cushion 03 . You or your child could pinch your

ngers, injuring them.

•

To avoid damage, ensure that the child safety seat is not jammed in between

hard objects (car door, seat rails, etc.).

•

Keep the child safety seat in a safe place when it is not in use. Do not place

any heavy objects on the seat and do not store it directly next to sources of

heat or in direct sunlight.

CAUTION! To protect your vehicle:

•

Certain car seat covers made from more sensitive materials (e.g. velour, leath-

er, etc.) may sustain signs of wear and tear when using child safety seats. For

optimum protection of your car seat covers, we recommend using the BRITAX

RÖMER car seat protector from our range of accessories.

PAGE II

A correctly set headrest 05 ensures that the diagonal seat belt section

18 is

optimally positioned, and gives your child optimum protection.

The headrest 05 must be adjusted so that there is a space two ngers wide

between the headrest 05 and your child's shoulders.

To adjust the height of the headrest to t your

child:

1. Grip the adjustment handle 06 on the back of the

headrest 05 and pull it upwards.

This unlocks the headrest.

2. You can now move the unlocked headrest 05 to

the desired height. As soon as you release the

adjustment handle 06 , the headrest 05 will lock

into place.

3. Place the child safety seat on the vehicle seat.

4. Have your child sit down in the child safety seat and

check the height. Repeat the procedure until the

headrest 05 has the correct height.

8. ADJUSTING THE HEADREST

9. INSTALLATION

10. SECURING YOUR CHILD

With 3-point belt

1. Carry out the steps in Section 8 "ADJUSTING

THE HEADREST“.

2. Place the child seat on the vehicle seat. Ensure

that the backrest 07 is ush with the backrest of

the vehicle seat.

Tip! If the headrest of the vehicle seat gets in the

way, turn it the other way.

3. Carry out the steps in Section 10 „SECURING

YOUR CHILD“. For the safety of your child, before every journey in the car check

that...

►the child safety seat is securely fastened;

►the lap belt

runs in the bright red belt guides on both sides of the seat

cushion

►the diagonal seat belt section 18 on the side of the vehicle seatbelt buck-

le 19 also runs through the light red belt guide 01 of the seat cushion,

►the diagonal seat belt section 18 runs through the dark red belt holder 02

of the headrest,

►the diagonal seat belt section 18 runs diagonally backward,

►the straps are tight and twisted,not

►the seatbelt buckle 19 must not be positioned on the red belt guide 01 in

the seat cushion.

If your child tries to open the vehicle belt buckle DANGER! 19 , stop the

vehicle as soon as safely possible. Check whether the child safety seat is

correctly fastened and ensure that your child is correctly secured. Explain

to your child the dangers associated with his actions.

UNFASTENING YOUR CHILD AND REMOVAL:

To unfasten your child or to remove the child safety seat, observe the

steps in Section 6 „REMOVAL“ [PAGE I]

The

KID II

is not installed permanently in the vehicle. It is simply secured

together with your child using the vehicle's 3-point seatbelt.

1. Have your child sit down in the child seat.

2. Pull out the vehicle belt and guide it in front of your

child to the vehicle seat buckle 19.

Ensure the vehicle belt is not twisted, as DANGER!

otherwise the full protective effect of the

retaining system is not ensured.

3. Engage the buckle tongue in the vehicle seat buck-

le 19 with a CLICK!

4. Place the diagonal seat belt section 18 and lap

belt section 17 on the side of the vehicle seatbelt

buckle 19 into the light red belt guide 01 of the seat

cushion.

The vehicle seatbelt buckle DANGER! 19 must

not be positioned between the light red

belt guide 01 and the armrest.

5. Also place the lap belt section 17 on the other side

of the seat cushion in the light red belt guide 01.

The lap belt section DANGER! 17 must lie as low

as possible over your child's hips on

both sides.

6. Guide the diagonal seat belt section 18 into the dark

red belt holder 02 of the headrest

05 until it lies

completely in the belt holder 02 and is not twisted.

Tip! If the backrest 16 conceals the belt holder 02 ,

you can adjust the headrest 05 upwards. The diagonal

seat belt section 18 can now be easily inserted. Now

return the headrest 05 to the proper height.

7. Make sure that the diagonal belt 18 runs over your

child's shoulder, and not in front of his or her neck.

Tip! You can still adjust the height of the headrest

05 again here in the vehicle.

The diagonal seat belt section DANGER! 18 must

run diagonally backward. You can

adjust the course of the belt with your

vehicle's adjustable belt deector.

The diagonal belt DANGER! 18 must never be di-

rected forwards to the belt deector on

the vehicle. In this case, use the child

safety seat on the back seat only.

8. Tighten the vehicle seat belt by pulling on the diag-

onal seat belt section 18.

17 01

If you have any further questions regarding its use, please feel free to

16 05

141210_KID_II_GB.indd 2 10.12.2014 11:00:19

Produkt Specifikationer

Mærke:	Britax
Kategori:	Bilsæde
Model:	Kid II
Bredde:	450 mm
Dybde:	510 mm
Vægt:	5100 g
Produktfarve:	Grå
type af sikkerhedssele:	3-punkt
Justerbar ryglæn:	Ja
Højde (min.):	660 mm
Højde (maks.):	850 mm
Gruppe:	2-3 (15 - 36 kg; 3.5 - 12 år)
Justerbar nakkestøtte:	Ja
Vaskbar dækning:	Ja