Britax KING II Manual

Britax Bilsæde KING II

Læs gratis den danske manual til Britax KING II (2 sider) i kategorien Bilsæde. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Britax KING II, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Adjustment lever

Headrest adjuster (KING II ATS/LS)

Lower belt guide

Release buttons

Seat shell

Upper belt guide Seat base

Indicator light (KING II LS)

Shoulder pads

Headrest

Headrest adjuster (KING II) Adjusting button

Shoulder straps

Harness buckle

Adjustment strap

Indicator light (KING II ATS)

Adjustment handle

User guide compartment

Harness retainer

17 16

KING II / ATS / LS

User instructions

www.britax.eu

2000021398 11/14

9 kg - 18 kg

9 M ~ 4 Y

2. INTRODUCTION

We are delighted that our

KING II / ATS / LS

can safely accompany your child

through a new stage in its life.

In order to protect your child correctly, the

KING II / ATS / LS

must al-

ways be used and installed as described in these instructions.

If you have any further questions regarding its use, please feel free to contact us:

These instructions use the following symbols stated below:

Symbol Keyword Explanation

DANGER! Risk of severe personal injury

WARNING! Risk of minor personal injury

CAUTION! Risk of material damage

TIP: Useful notes

Instructions that follow a set sequence are numbered.

Example:

1. Press the button...

Belt guide colours

For better differentiation, the two vehicle seat

belts are highlighted in different colours. The di-

agonal seat belt 21 in dark red and the lap belt

22 in bright red. The colour of the belt guides

on the child safety seat follows the same colour

scheme.

4. CARE AND MAINTENANCE

3. CERTIFICATION

/ USAGE

PAGE I

5. DISASSEMBLY AND DISPOSAL

1. PRODUCT OVERVIEW

DISPOSAL:

Please observe the waste disposal regulations in your country..

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, thermal utilisation

Plastic parts According to the labelling in the

corresponding container

Metal parts Container for metals

Belt straps Container for polyester

Buckle and tongue Residual waste

Batteries Container for batteries

REMOVAL:

UNFASTENING YOUR CHILD:

1. To unfasten your child, press the red release button of the 5-Point harness

buckle 12 .

1. Unbuckle the vehicle belt buckle 20 and loosen the harness straps.

2. Unhook the diagonal belt section 21 from the upper belt guide 01 .

3. To open the shell: push one of the grey release buttons

03 and at the

same time pull the seat shell 02 as far forward as possible.

4. Remove the diagonal 21 and the lap belt sections 22 from the light red

lower belt guides 04 .

5. Hold the seat shell 02 with one hand while pulling the grey adjustment

lever 05 forward with the other hand.

6. To close the shell: tip the seat shell 02 against the seat base 06 over both

engagement positions.

WARNING! To avoid injuries take your hand away from the grey adjust-

ment lever 05 , as soon as getting over the two engagement positions.

7. Push the seat shell 02 with both hands against the seat base 06 until it is

fully engaged.

BRITAX RÖMER

Child safety seat

Testing and certication

In accordance with ECE* R 44/04

*ECE = European Standard for Child Safety Equipment

Group Body weight

KING II / ATS / LS

I 9 to 18 kg

The child safety seat has been designed, tested and certied according to the re-

quirements of the European Standard for Child Safety Equipment (ECE R 44/04).

The seal of approval E (in a circle) and the approval number are located on the

orange approval label (sticker on the child safety seat).

DANGER! This approval will be invalidated if you make any modications to

the child safety seat. Only the manufacturer is permitted to make

modications to the child safety seat.

Never secure your child or the child safety seat with a 2-point belt. DANGER!

If you secure your child in the child seat with only a 2-point belt,

then in the event of an accident this may cause serious injuries to

your child, possibly resulting in death.

Please observe the instructions for using children’s restraining systems in the operating

instructions of your vehicle. 3-point retractor safety-The seat can only be used in vehicles with

belts

Please nd the information on the seats approved for child safety seats of the weight classes 9 to

18 kg in the operating instructions of your vehicle.

You can use your child safety seat as follows:

In the direction of travel yes

Against the direction of travel no

with 2-point belt no

with 3-point reractor safety belt

2) yes

on front passenger seat yes

on outer rear seat yes

on centre rear seat (with 3-point

belt2))

yes 4)

1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only

if the vehicle seat is also approved for use by adults. The seat may not be in the area of effect

of an airbag.

2) The seat is only compatible with 3-point retractor type safety-belts, approved to ECE Reg

No. 16 or other equivalent standards.

3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions

in vehicle owner’s manual.

4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.

9 - 18 kg

Removing the cover

Loosen the harness straps as far as possible.

1. Open the harness buckle 12 (press red button).

2. Remove the cover of the headrest 09 .

3. Open the poppers 29 on the left and right side of the

rear part of the cover.

4. Unhook the elastic seam of the cover under the edge of

the seat shell.

TIP: Start at the sides of the seat shell.

5. Pull the cover up and over the bezel of the strap adjuster.

6. Feed out the harness buckle 12 and the end of the strap

from the cover.

7. Pull the cover upwards and remove it over the headrest

09 .

The cover can now be washed. Please observe the

instructions on the washing label of the cover:

Re-tting the cover

Proceed in reverse order to put on the cover.

Please ensure that you only use the original BRITAX RÖMER replacement seat

covers, as the seat cover is an integral part of the child safety seat and fulls im-

portant functions to ensure the smooth operation of the system. Replacement seat

covers are available from your dealer.

• The cover can be removed and washed using the delicates programme of the

washing machine (30°C). Please observe the instructions on the washing label

of the cover.

• The plastic parts can be cleaned with a damp cloth. Do not use any caustic

cleaning agents (such as solvents).

DANGER! The child seat must not be used without the seat cover.

Care for the harness buckle

It is vital for the safety of your child that the harness buckle works correctly. Malfunctions

of the harness buckle are usually caused by accumulations of dirt or foreign bodies.

Malfunctions include the following:

• The buckle latches are ejected only slowly when the red release button is pressed.

• The buckle latches will no longer lock home (i.e. they are ejected again if you try to push

them in).

• The buckle latches engage without an audible “click“.

• The buckle latches are difcult to insert (you feel resistance).

• The buckle only opens if extreme force is applied.

Remedy: wash out the harness buckle so that it functions properly once again.

Cleaning the harness buckle

1. Open the harness buckle 12 (press the red button).

2. Adjust the seat shell 02 to the upright seating

position.

3. Open the Velcro fastener on the crotch pad 25 and

remove it and retain it.

4. Grasp below the seating area the metal plate

which keeps the buckle 12 at the seat base and

turn it into a vertical position.

5. Slide the metal plate 26 through the slot 27 .

6. Soak the harness buckle 12 in warm water with

dishwashing liquid for at least an hour.

7. Rinse and dry the harness buckle 12 thoroughly.

8. Slide the metal plate 26 edgewise through the slot

27 in the cover and the seat base.

9. Rotate the metal plate 26 90°

DANGER! Pull the harness buckle 12 rmly to ensure

that it is securely fastened.

10. Insert the crotch pad 25 through the slot 27 and

secure the Velcro fastener.

Cleaning the occupant sensor

1. Fold the lower part of the cover updwards.

2. Remove dirt and dust in the area of the occupant sensor

28 with a vacuum cleaner.

DANGER! The occupant sensor 28 must not come in

contact with water.

141106_KING_II_ATS_LS_GB.indd 1 06.11.2014 09:34:59

Produkt Specifikationer

Mærke:	Britax
Kategori:	Bilsæde
Model:	KING II
Bredde:	450 mm
Dybde:	540 mm
Højde:	670 mm
Vægt:	10300 g
Produktfarve:	Lilla
Monteringstype:	Sikkerhedssele
type af sikkerhedssele:	3-punkt
Gruppe:	1 (9 - 18 kg; 9 måneder - 4 år)
Justerbar nakkestøtte:	Ja