Broan FIN-6MD Manual

Broan Klimaanlæg FIN-6MD

Læs gratis den danske manual til Broan FIN-6MD (4 sider) i kategorien Klimaanlæg. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Broan FIN-6MD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

FRESH IN

FIN-6MD

INSTALLATION NSTRUCTIONS I

Please take note that this manual uses the following symbols to emphasize particular information:

⚠ WARNING

Identifies an instruction which, if not followed, might cause serious personal

injuries including possibility of death.

CAUTION

Denotes an instruction which, if not followed, may severely damage the unit

and/or its components.

💡 Indicates a supplementary information that may relate to optional parts or

simply aim to facilitate a task.

⚠WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE

FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer.

2. Before cleaning this unit, turn off the power to the AHU at service panel. (Powered by AHU)

3. This unit is not designed to provide combustion and/or dilution air for fuel-burning appliances.

4. Installation work must be done by qualified person(s) in accordance with all applicable codes and standards,

including fire-rated construction.

5. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.

6. When cleaning or performing installation of this unit, it is recommended to wear safety glasses and gloves.

7. When applicable local regulation comprises more restrictive installation and/or certification requirements,

the aforementioned requirements prevail on those of this document and the installer agrees to conform to

these at his own expense.

8. The unit must be mounted at least 3.3 feet (1.0 meter) away from any accessible opening of the duct.

9. Must be powered using a Class 2 transformer rated 10VA or higher.

CAUTION

1. Please read specification label on product for further information and requirements.

2. Do not intake air into spaces within walls or ceiling or into attics, crawl spaces, or garage. Do not attempt

to recover the exhaust air from a dryer or a range hood.

3. Intended for residential installation only in accordance with the requirements of NFPA 90B.

4. When leaving the house for a long period of time (more than two weeks), a responsible person should

regularly check if the unit operates adequately.

5. At least once a year, the unit mechanical and electronic parts should be inspected by qualified service

personnel.

6. Since the electronic control system of the unit uses a microprocessor, it may not operate correctly because

of external noise or very short power failure. If this happens, turn power off at AHU service panel and wait

approximately 10 seconds. Then, restore the power to the unit.

7. Outdoor intake hood must be weather tight and comprise a bird screen.

8. Should you decide to dispose of this unit or of parts of it, do so in accordance with local laws and regulation.

⚠ RESIDENTIAL USE ONLY ⚠

For complete warranty statement, and to register your

product online, go to www.broan-nutone.com.

READ AND SAVE THESE

INSTRUCTIONS

1. PREPARATION

Before you start:

Choose the best location and installation type for the FIN-6MD according to the current system. Ducting

widely affects the performance of this type of device. Use the shortest, straightest duct run possible to

maximize the results.

CAUTION

Do not install in an area where the temperature may exceed 160°F.

The installer shall ensure that, if necessary, an in-line heater sized according to the required airflow and outside

design heating temperature from Manual J or ASHRAE table is installed to ensure that the air delivered to the

AHU is never below the minimum temperature allowed by the manufacturer. The in-line heater shall have an

integrated airflow sensor and an over temperature sensor to prevent heating in no-flow or low-flow conditions.

When deciding if a preheater is required and whether it should be installed BEFORE or AFTER the FIN-6MD,

consider the following:

• The FIN-6MD’s minimum operating temperature is -4°F.

• The temperature distributed to the AHU should never be below the temperature recommended by the

AHU manufacturer.

• The minimum distance between the preheater and the FIN-6MD is 12 inches.

2. INSTALLATION

Always respect the orientation of the FIN-6MD and the direction of the airflow, as indicated on the

unit.

Direct-to-AHU is the fastest and easiest method:

1. Make a 6-inch diameter hole in the return duct of

your AHU.

2. Install the seal on the FIN-6MD port that will insert

the AHU ducting. Make sure that the direction of the

airflow indicated on the unit is respected.

3. Install the 3 installation brackets on the unit, as

illustrated.

4. Mark and drill holes for the brackets on the AHU

ducting and, using appropriate screws, secure the

FIN-6MD to the duct of the AHU, making sure it is

level horizontally.

💡 Use self-drilling screws (not included) to avoid

marking and drilling steps.

5. Follow steps in section 3 to connect the insulated

duct to the FIN-6MD.

6. Perform the electrical connection to the AHU following the wiring diagram in section 4.

Through a horizontal surface:

1. Make a hole in the surface that the duct will run

through. Size the hole so that the vapor barrier of the

insulated ducting is not damaged, and the insulation

not compressed.

2. Install the 3 installation brackets on the unit, as

illustrated.

3. Run a piece of insulated duct through the hole and

connect to the FIN-6MD following the steps in

section 3. Make sure the direction of the airflow as

indicated on the unit is respected.

4. Push the excess ducting on the other side of the

surface and, using appropriate screws, secure the

FIN-6MD to the surface.

5. Run the insulated duct to the AHU and connect to

the AHU ducting, making sure that the vapor barrier

sealing is leak-free.

6. Follow steps in section 3 to connect the second

insulated duct to the FIN-6MD.

7. Perform the connections to the AHU following the

wiring diagram in section 4.

Mounted under, above or beside a structure:

1. Install 2 installation brackets on the unit, as illustrated, according to the surface the unit will mount to.

2. Using appropriate screws, secure the FIN-6MD to the structure, making sure it is level horizontally. Make

sure the direction of the airflow as indicated on the unit is respected.

3. Follow steps in section 3 to connect both insulated ducts to the FIN-6MD.

4. Run the insulated duct to the AHU and connect to the AHU ducting, making sure that the vapor barrier

sealing is leak-free.

5. Perform the connections to the AHU following the wiring diagram in section 4.

MOUNTED UNDER

MOUNTED ABOVE

MOUNTED BESIDE

SUSPENDED

LOGIC DIAGRAM

WIRING COLOR CODE

Reference : 1103507 rev. C

BLK BLACK

BLU BLUE

GRN GREEN

PNK PINK

RED RED

WHT WHITE

YEL YELLOW

Low voltage factory wiring

Low voltage ﬁeld wiring

LED1

(power)

LED2

(Status)

RED

BLU

YEL

PNK

Damper Motor

Harness

Standby Switch

AHU Wiring

ELECTRONIC ASSEMBLY

Mode

Selection

CFM Ratio/

Damper

Selection

Power

Supply

(12V)

Low Voltage

(24VAC)

PTC

J4-7

J4-6

J4-4

J4-5

Power

Supply

(3.3V)

MCU

Stepper

Driver

J5-1,2,3,4

WIRING DIAGRAM

Not Used

Humidity/

Temperature

Sensor

GRN

RED

WHT

BLK

MCU

+24VAC Supply

Mode

Accessory

FIN-DCS

Accessory Kit

Voltage

Detection

J1-2

J1-1

Accessory

24VAC

(optional)

3. CONNECTING THE INSULATED DUCTS TO THE UNIT

CAUTION

Always use insulated ducting of a minimum R-4 insulation factor.

1. Slide the inner flexible duct over the port and secure it using a tie wrap.

2. Pull the insulation over the flexible duct and port without compressing it.

3. Use duct tape to seal the outer membrane of the insulated duct to the outer ring of the port.

⚠WARNING

Make sure the outdoor intake hood is at least 18 inches above the ground and 6 feet away

from any of the following: Dryer exhaust, high-efficiency furnace vent, central vacuum vent,

gas meter exhaust, gas barbecue-grill, any exhaust from a combustion source, garbage bin

and any other source of contamination.

💡 Make sure that the outdoor intake hood is easily accessible for annual maintenance. If located above the

first floor, place it close to a window or balcony to allow easy access.

4. WIRING DIAGRAM

⚠WARNING

Risk of electric shock. Electrical wiring must be done by qualified personnel in

accordance with all applicable codes and standards. Before connecting wires, switch off

the power to the AHU at service panel and lock service disconnecting means to prevent

power from being switched on accidentally.

CAUTION

Faulty connections can cause damage to the AHU, to the thermostat and/or to this unit.

Always double check connections before turning power back on.

Scan to view our

installation video.

5011110

CONFORM TO

UL STD. 1995

💡 The terminal block can

be removed for easier

connection.

💡 Use the included tie

wrap and the loop

above the terminal

block to secure the

wires and reduce

the risk of broken

connections.

Seal

AHU wiring next page

1103500D

Produkt Specifikationer

Mærke:	Broan
Kategori:	Klimaanlæg
Model:	FIN-6MD

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan FIN-6MD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Klimaanlæg Broan Manualer

Broan B130H65RT Manual

22 Juli 2025

Broan B130E65RT Manual

21 Juli 2025

Broan B110H65RT Manual

21 Juli 2025

Broan B130E65RS Manual

21 Juli 2025

Broan B150E75NT Manual

20 Juli 2025

Broan B130H65RS Manual

20 Juli 2025

Broan B150H75NS Manual

20 Juli 2025

Broan B160E65RS Manual

20 Juli 2025

Broan B150E75NS Manual

20 Juli 2025

Broan B150H75NT Manual

20 Juli 2025

Klimaanlæg Manualer

Nyeste Klimaanlæg Manualer

Vevor JH-120Y Manual

21 November 2025

Saivod ASCT0924 Manual

20 November 2025

Friedrich ZoneAire Premier ZHV16DA Manual

19 November 2025

Friedrich Chill Premier CCF05B10C Manual

19 November 2025

Friedrich Chill Premier CCF06B10C Manual

19 November 2025

Vevor YH-F02 Manual

18 November 2025

Friedrich Chill Premier CCF08B10C Manual

18 November 2025

Whynter ARC-147WF Manual

18 November 2025

Whynter ARC-147WFH Manual

18 November 2025

Whynter ARC-1230WN Manual

18 November 2025