Brother LX-570 Manual

Brother Lamineringsmaskine LX-570

Læs gratis den danske manual til Brother LX-570 (9 sider) i kategorien Lamineringsmaskine. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Brother LX-570, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/9
Cutter. The cutter is for trimming the
backing material and slides on the
cutter bar. It can be replaced.
Knob
Cutter bar
Latch (opens top cover)
Feed Deck. The LX-570 is designed for
use with items up to five inches wide. It
works best with item thicknesses
between 20 pound bond paper and 100
pound card stock or construction paper
(min. thickness is 0.004 inches, max.
thickness is 0.010 inches).
The LX-570 applies an adhesive, laminate, or
magnetic backing to an item without using heat or
electricity. You choose a backing by swapping the
drop-in cartridge.
The LX-570 comes with a starter cartridge already
installed. This cartridge applies a permanent
adhesive backing and is shorter than replacement
cartridges.
See the reverse for available cartridges and for
application ideas on using your LX-570. First, take a
few minutes to read these instructions.
Top Cover. Your LX-570
comes with a "starter"
cartridge already
installed, which applies a
permanent adhesive
backing to an item.
Cut:
When the item clears the cutter at the exit
area, gently push down on the cutter knob
and slide it all the way to the left or right.
Insert the item:
Insert the item face up at the feed
deck and turn the knob in the direction
of the arrows only; do not turn knob
backwards.
To avoid wasting the backing material,
note the location of the cut. Feed only
enough material to clear the cutter.
How to Use the LX-570
Insert the item
and be sure it
is straight.
Insert until you
feel contact;
then release it
as you turn
knob.
Exit area
When Using the
Starter Cartridge...
Feed and cut the item as described here. Be
sure to feed face up.
Press down firmly around all the edges. This
action prevents adhesive from remaining on
the front of the item. Then remove the clear
film and discard carefully as it is sticky.
When you are ready to place the item on a
surface, peel it from the white backing.
This starter cartridge contains five feet of
backing material. After you use it a few times,
always make certain that it contains sufficient
material. If uncertain, install a new cartridge
to avoid partial processing.
Note: the starter cartridge is shorter than the
replacement cartridges. See the other side
for cartridge descriptions and lengths. Always
consult packaging of replacement cartridges.
User’s Guide
12
LX-570 About the LX-570
Feed straight, not at an angle.
Turn the knob forward only.
Notes:
Before using, remove the protective tape
and other packaging materials under the
top cover.
Under the terms of an agreement with
Xyron, Inc., the purchase or
other acquisition of this product confers
no right or license to use
the product in the Retroreflective Field.
How to Change the Cartridge
Remove the cartridge:
Lift up the latch to open the top cover. Then
grasp the cartridge in one hand, hold the
LX-570 with the other, and lift the cartridge
up and out.
Insert a cartridge:
Open the top cover and lower
the cartridge in with the label up,
facing the feed deck.
As you lower the cartridge, be
sure that the backing material
fits underneath the cutter bar at
the exit area.
Close the top cover by gently
pushing down until it clicks and
is fully seated.
1
1
1
11
Unsnap the cutter:
Place your thumb underneath the back of the
cutter knob and your index finger on the cutter
bar. Lift up with your thumb to unsnap the cutter
from the cutter bar.
How to Change the Cutter
Blade is at this end and fits into
a groove on the cutter bar.
Always avoid touching the
blade.
Snap the new cutter into place:
At any point on the cutter bar, place the front
of the cutter into the groove on the cutter bar
so the blade fits into it. Then rotate the cutter
back and snap down.
Blade is at front of cutter.
Avoid touching the blade.
Back of cutter
Front of cutter
Guide the backing
material under the cutter
bar into the exit area.
Notes: When placing a partially-used
cartridge back in the machine, be sure
the material does not adhere to the
cartridge itself.
When removing a used cartridge
whose material has wrapped around
the rollers, remove the cartridge and
pull the material from the rollers.
Groove in cutter bar
1
1
1
11
1
1
1
11
2
2
2
22
2
2
2
22
When installed properly, the cutter slides
back and forth on the cutter bar.
The cartridge is properly installed when
the label is flush with the feed deck.
Close the top cover before using.

Produkt Specifikationer

Mærke: Brother
Kategori: Lamineringsmaskine
Model: LX-570

Har du brug for hjælp?

Hvis du har brug for hjælp til Brother LX-570 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lamineringsmaskine Brother Manualer

Brother

Brother HAK180 Manual

31 Juli 2025
Brother

Brother Cool LX-910D Manual

24 Januar 2024
Brother

Brother Cool LX-1200 Manual

17 August 2023
Brother

Brother LX-1200 Manual

9 November 2022
Brother

Brother LX-570 Manual

8 November 2022

Lamineringsmaskine Manualer

Nyeste Lamineringsmaskine Manualer

Wallner

Wallner DWL-4CF Manual

27 September 2025
Wallner

Wallner LM341 Manual

26 September 2025
Wallner

Wallner LS245B Manual

25 September 2025
Wallner

Wallner OL290 Manual

25 September 2025
Wallner

Wallner DWL-3AF Manual

25 September 2025
Dahle

Dahle 70103 Manual

25 September 2025
GBC

GBC 240HS Manual

24 September 2025
GBC

GBC 240 Manual

24 September 2025
GBC

GBC Academy+ Manual

23 September 2025
GBC

GBC 250HS Manual

23 September 2025