C Pure Oceanloch+ L2 Manual

C Pure Vandfilter Oceanloch+ L2

Læs gratis den danske manual til C Pure Oceanloch+ L2 (1 sider) i kategorien Vandfilter. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2 anmeldelser. Har du et spørgsmål om C Pure Oceanloch+ L2, eller vil du spørge andre brugere om produktet?

Side 1/1
INCLUDED IN PACKAGE
4 x 7.5" Self-Seal Bubble Wrap Bag
3/8" Sch 80 Tee with 3/8" x 1/4"
Reducer Bushing
3/8" Double O-Ring Short Nipple
3/8" Threaded PVC Ball Valve
2" 0-100psi Steel Gauge
2 @ #10 x 1" SS Screws
Instruction Sheet
water supply.
Do not use to treat water that is microbially unsafe or of unknown quality without adequate
disinfection before and after the system.
The system must be installed in accordance with all applicable state and local laws
and regulations.
Filter cartridge must be replaced every 3-6 months,
or at the rated capacity, or if a noticeable reduction in
flow rate occurs.
INSTALLATION INSTRUCTIONS
1. Shut off power to equipment if necessary.
2. Turn off water supply to system.
3. Remove the cartridges from the system following the instructions.
4. Place and install the filter system using the two #10 x 1 stainless screws "
provided for wall mounting. Allow at least 3 of space below the cartridge for "
easy removal and replacement.
5. Install inlet ball valve and outlet pressure gauge (as shown).
5a. If you’re installing a system with an inlet pressure gauge, attach the inlet
gauge to the inlet side of the system. Then, install inlet ball valve to the inlet
pressure gauge.
6. Connect inlet and outlet ports using appropriate NSF-approved components.
Do not connect the outlet port to equipment until after flushing (Step 10).
7. Lubricate O-rings on cartridges with a food grade silicone lubricant prior to
installation.
8. Line up locking features as shown and push cartridge up into head until it stops.
Use free hand to support at top of bracket. Turn cartridge 1/4 turn to the right
until it stops to lock in place.
9. Connect a piece of tubing to the outlet port and run it to a drain or bucket.
10. Turn on water to the system. Allow water to run to drain for 5 minutes to purge
air and rinse out carbon fines.
11. Turn off water. Connect system to equipment.
12. Turn on water. Check for leaks and repair as needed.
13. Restore power to equipment. The system is ready for operation.
ININ
ALIGNMENT POINTS
INLET
OUTLET
CARTRIDGE REPLACEMENT
TO REMOVE OLD CARTRIDGE
Twist to the left to unlock
TO INSTALL NEW CARTRIDGE
Align with guide point
Push straight up
Pull straight down
Twist to the right to lock
04/2025
#790OCLOKITL2,
#790OCLOKTL2G
System Model
Flow Rate
(GPM) (LPM)
790OCLOKITL2 3.33 12.64
Capacity
Replacement Part
Number
(G) (L)
36,000 136,260 790OCLOCRTL2
Max Operating
Temp.
Max Operating
Pressure
100°F (38°C)
125 PSI
(8.62 bar)
OCEANLOCH+ L-2 REV 1 4-20
INSTALL ATION MANUAL
L
+


Produkt Specifikationer

Mærke: C Pure
Kategori: Vandfilter
Model: Oceanloch+ L2

Har du brug for hjælp?

Hvis du har brug for hjælp til C Pure Oceanloch+ L2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Vandfilter C Pure Manualer

Vandfilter Manualer

Nyeste Vandfilter Manualer

Scotsman

Scotsman SSM2-P Manual

14 Juni 2025
Scotsman

Scotsman SSM3-P Manual

14 Juni 2025
Emga

Emga 340001 Manual

31 Marts 2025
Everpure

Everpure H-1200 Manual

21 Februar 2025
GE

GE GXRLQK Manual

21 Februar 2025
Philips

Philips AWP1812 Manual

7 Februar 2025
Oase

Oase AquaSkim 20 Manual

3 Februar 2025