Cambro VCSHD158 Manual

Cambro Boks VCSHD158

Læs gratis den danske manual til Cambro VCSHD158 (4 sider) i kategorien Boks. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Cambro VCSHD158, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Owner’s

Manual

Versa Cart

Cambro Versa

Food Service System

This owner’s manual applies to all Versa Cart models.

VCSWRHD

Table of Contents

Introduction �� 1

Section I Operating Instructions ��2

Section II Mobility 3��

Section III Cleaning and Maintenance �� 3

Section IV Optional Accessories �� 4

Section V Warranty �� 4

Section VI Replacement Parts ��4

Introduction

Congratulations on the purchase of your new Cambro Versa Cart� This Owner’s Manual provides

you with a step-by-step guide to assembling, operating and maintaining your Versa Cart�

If you have any further questions, please do not hesitate to contact your

Cambro Sales Representative, visit our Web site at www.cambro.com

or call our Customer Service Department at 800 833 3003.

D060912_Versa Cart ENG MN.indd 1 10/22/09 1:22:08 PM

Section I – Versa Cart Operating Instructions

Applies to all Versa Cart models�

Versa Cart Parts List

A� 1 Versa Cart Body and Counter Top Section

B� 1 Key and Lock Set

C� 1 piece Electrical Access Port Cover

D� 2 piece Electrical Access Port Cover

E� 28 Black Snap-in Plugs

F� 1 Asset Management Label

No assembly required: The Versa Cart comes assembled�

Adjusting the Height of the Tray Rails

Remove the drawer by unscrewing both knobbed bolts located under and inside the drawer interior area� 1�

Remove the drawer from Cart body�2�

Remove the adjustable shelf and nylon thumbscrew from the Cart�3�

After picking desired side and height position on the Cart, remove the small black plugs from both inside and outside of the Cart wall where rail will be located�4�

Remove the 3-¼" (8,25 cm) screws and washers that hold the rail mount to the Cart body� 5�

Position the rail mount to the new location on the Cart body� 6�

Use the 3-¼" (8,25 cm) screws and washers (4 each) placing them through the sidewall from the inside outward and into the rail mount� Once all four screws are 7�

started, tighten with a screwdriver until mount is level and properly snug against Cart body�

Place one of the nylon bushing into the recessed hole of one side of the rail mount� Place tray rail onto the exposed bushing end�8�

Install second bushing through the rail slide on the opposite side and into the recessed hole on that side of mount base�9�

With the rail hanging from bushings install two black knob bolts through each bushing and engage into the threads of the mount base� Tighten by hand�10�

To check rail, lift to a slightly higher than level position and push inward towards cart body until angled portions of the rail and mount base engage and stop� 11�

Rail should rest into a level position�

To lower the rail, slightly lift and pull rail outward and down�12�

With rail mounting complete, place the black plugs back into remaining holes in the Cart wall being sure to install on both the inside and outside locations� 13�

Adjusting the Versa Cart Shelf

1� Remove the nylon bolt and remove the shelf�

2� Place the shelf at the desired location�

3� Using a nylon bolt, tighten to secure the shelf in place�

4� Place the snap-in plugs into the remaining threaded holes�

D060912_Versa Cart ENG MN.indd 2 10/22/09 1:22:09 PM