Casio 2926 Manual
Læs nedenfor 📖 manual på dansk for Casio 2926 (4 sider) i kategorien Ur. Denne guide var nyttig for 18 personer og blev bedømt med 3.5 stjerner i gennemsnit af 9.5 brugere
Side 1/4
Operation Guide 2926
1
MO0503-EB
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully and keep it on hand for later reference
when necessary.
Warning!
•The longitude, lunitidal interval, Moon phase indicator, tide graph data, and solar
azimuth data that appear on the display of this watch are not intended for
navigation purposes. Always use proper instruments and resources to obtain data
for navigation purposes.
•This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of tidal
movements only.
•When engaging in mountain climbing or other activities in which losing your way
can create a dangerous or life-threatening situation, always be sure to use a
second compass to confirm direction readings.
•CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
About This Manual
•Button operations are indicated using the letters shown
in the illustration.
•Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
(Light)
General Guide
•The illustration below shows which buttons you need to press to navigate between
modes.
•In any mode, press L to illuminate the display.
Moon / Tide Data Mode Countdown Timer Mode
Dual Time Mode
Timekeeping Mode
▲
▲
▲
Alarm Mode
▲
▲
Stopwatch Mode
Press C.
▲
Press .B
▲
Bearing Mode
Press .C
▲
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
•The tide graph shows tidal movements for the current
date in accordance with the current time as kept in the
Timekeeping Mode.
•The Moon phase indicator shows the current Moon
phase in accordance with the current date as kept in the
Timekeeping Mode.
Important!
•Moon phase, tide graph data, Bearing Mode solar
azimuth data, and Moon/Tide Data Mode data will not
be displayed properly unless the Timekeeping Mode
current date and time settings and Home Site data are
configured correctly. See “Home Site Data” for more
information.
Day of week
Month – Day
Hour : Minutes Seconds
PM
indicator
Tide graph
Moon phase indicator
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Hour
Seconds
12/24-Hour
Format
Day Month Year
Minutes
3. When the setting you want to change is flashing, use D B and to change it as
described below.
|
|
|
|
|
|
|
|
|
|
|
|
|
Year
To change this setting
Seconds
Hour, Minutes, Year,
Month, Day
12/24-Hour Format
Perform this button operation
Press .D to reset to 00
Use D(+) and B(–) to change the setting.
Press D to toggle between 12-hour (12H) and
24-hour ( ) timekeeping.24H
4. Press A twice to exit the setting screen.
•The first press of A displays the GMT differential setting screen. Pressing A again
exits the setting screen.
•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
•The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Home Site Data
Tide graph data and Bearing Mode solar azimuth data will not be displayed properly
unless Home Site data (GMT differential, longitude, and lunitidal interval) is configured
correctly.
•The GMT differential is the time difference of the time zone where the site is located
from Greenwich Mean Time.
•Note that you must add one hour to the GMT differential for your time zone
whenever you change to Daylight Saving Time. Subtract one hour when you change
back to Standard Time.
•The lunitidal interval is the time elapsing between the Moon’s transit over a meridian
and the next high tide at that meridian. See “Lunitidal Interval” for more information.
•This watch displays lunitidal intervals in terms of hours and minutes.
•The “Site/Lunitidal Interval Data List” provides GMT differential, longitude, and
lunitidal interval information around the world.
•The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch and whenever you have the battery replaced. Change these
settings to match the area where you normally use the watch.
GMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
20 minutes)
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the GMT differential setting
screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
Lunitidal Interval
Hours Lunitidal Interval
Minutes
Longitude
GMT
Differential
4. When the setting you want to change is flashing, use and D B to change it as
described below.
GMT differential
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting
GMT Differential
Longitude
Lunitidal Interval
Hours, Minutes
Screen Button Operations
Use D(+) and B(–) to change the setting.
•Yo u can specify a value in the range of –11.0
to +14.0, in 0.5-hour units.
Use D(+) and B(–) to change the setting.
•Yo u can specify a value in the range of
179°W to 180°E, in 1-degree units.
Use D(+) and B(–) to change the setting.
5. Press A to exit the setting screen.
Bearing Mode
The Bearing Mode lets you determine approximate
directions using a displayed angle value that indicates the
angle to the sun (solar azimuth).
•All of the operations in this section are performed in the
Bearing Mode, which you can enter from the
Timekeeping Mode by pressing B.
Important!
Before the watch can calculate the solar azimuth (the
angle of the sun in relation to your location) correctly, you
must first set the correct current time, current date, and
Home Site in the Timekeeping Mode. You must also
specify whether the sun traverses the sky to the north or
to the south of your current position.
Solar azimuth
•Note that you cannot use the Bearing Mode to determine directions in the following
cases.
When the sun is not visibl
e
At night
When sun traverses the sky directly overhead or when you cannot determine if it
traverses to the north or south
To set the traverse direction of the sun
1. In the Bearing Mode, hold down A until N or S flashes
on the display. This indicates the setting screen.
2. Press D to toggle the setting between N (north) and S
(south).
3. Press A to exit the setting screen.
•At this time the watch uses the traverse direction setting
you just configured and the Timekeeping Mode data to
calculate and display the solar azimuth.
|
|
|
|
|
|
|
|
|
|
|
|
|
Operation Guide 2926
2
To determine your bearings
1. Enter the Bearing Mode.
•This displays the current solar azimuth value in accordance with the current
Timekeeping Mode data (time, date, Home Site data).
2. Find the same value on the bezel as the angle value displayed for the solar azimuth
on the Bearing Mode screen.
3. Position the watch so the value you found in step 2 is pointing at the sun.
4. The 12 o’clock position of the watch should now be pointed north.
•Note that the bearings produced by the Bearing Mode are intended for general
reference only.
North
Bezel
Moon/Tide Data
Moon/tide data lets you view the Moon age and Moon
phase for a particular date, and tidal movements for a
particular date and time for the Home Site.
•If you suspect that the Moon/tide data is not correct for
some reason, check the Timekeeping Mode data
(current time, date, and Home Site settings), and make
changes as required.
•See “Moon Phase Indicator” for information about the
Moon phase indicator and “Tide Graph” for information
about the tide graph.
•All of the operations in this section are performed in the
Moon/Tide Data Mode, which you enter by pressing C.
Moon phase indicator
Moon age
Tide graph
Moon/Tide Data Screens
Each press of in the Moon/Tide Data Mode toggles between the Moon DataA
screen and the Tide Data screen.
•When you enter the Moon/Tide Data Mode, the data that appears first is the Moon
data (Moon age and Moon phase indicator) for the current date as kept by the
Timekeeping Mode.
▲
▲
Press .A
Tide Data ScreenMoon Data Screen
Tide gragh
Time
Moon age
Moon phase indicator
Year Month – Day
To view the Moon data for a particular date
While the Moon Data screen is displayed in the Moon/Tide Data Mode, use (+) andD
B (–) to display the date whose Moon data you want to view.
•You can select any date from 2000 to 2039.
To view tide data for a particular time
1. While the Moon Data screen is displayed in the Moon/Tide Data Mode, use D (+)
and B (–) to display the date whose tide data you want to view.
2. Press A to switch to the Tide Data screen.
•The initial screen shows the tide graph for 6:00 AM.
3. Specify the time for which you want to display tide data.
•Use D (+) and B (–) to change the time in one-hour steps.
Countdown Timer
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer has two
modes: auto-repeat and elapsed time, and a progress
beeper signals the progress of the countdown. All of this
makes the countdown timer a valuable tool for timing the
start of a yacht race.
•All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Configuring Countdown Timer Settings
The following are the settings you should configure before actually using the
countdown timer.
Countdown start time and reset time
Timer mode (auto-repeat, elapsed time)
Progress beeper on/off
Timekeeping Mode time
Minutes Seconds
•See “To configure countdown timer settings” for information about setting up the
timer.
Reset Time
Yo u can set a “reset time,” which is a kind of alternate countdown start time you can
recall with the press of a button any time a countdown operation is in progress.
Timer Mode
The countdown timer gives you a choice of two modes: auto-repeat and elapsed time.
Auto-repeat
Auto-repeat automatically restarts the countdown from the countdown start time
whenever zero is reached.
•Auto-repeat mode is best when timing the starts of match races.
•Even if you start a countdown operation from the reset time, the countdown
automatically restarts from the countdown start time whenever it reaches zero.
•Auto repeat timing repeats up to seven times.
Elapsed Time
When the end of the countdown is reached in the elapsed time mode, the timer
automatically switches to an elapsed time measurement operation.
•The elapsed time mode is best when timing the speed of yachts during ocean races.
•The elapsed time operation is performed in one-second increments up to 99 hours,
59 minutes, 59 seconds.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown reaches
zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than
the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal
when the countdown reaches zero.
•The countdown end beeper always sounds, regardless of the on/off status of the
progress beeper.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and a reset
period progress beeper.
•The reset time beeper and reset period progress beeper sound only while the
progress beeper is turned on.
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. When the progress
beeper is turned on, the watch beeps each second of the final 10 seconds before the
countdown reaches the reset time.
Reset Period Progress Beeper
The reset period is the portion of the countdown between the reset time and zero.
When the progress beeper is turned on, the watch emits four short beeps at the top of
each minute during the reset period, and 30 seconds before the end of the
countdown.
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat;
Progress beeper: On
10'00"
Start Time Reset Time
0'00"1'00" 0'30"2'00"3'00"4'00"5'00"
Reset Period
Reset Period Progress Beeper
Countdown
End Beeper
Reset Time Beeper
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time;
Progress beeper: Off
10'00" 0'00"5'00"
Countdown
End Beeper
Elapsed time
measurement
Start Time Reset Time
To configure countdown timer settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the
countdown start time setting starts to flash, which
indicates the setting screen.
•If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Start
Time Reset
Time Timer
Mode Progress
Beeper
3. When the setting you want to change is flashing, use and D B to change it as
described below.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting
Start Time
Reset Time
Timer Mode
Progress
Beeper
Screen Button Operations
Use D (+) and B (–) to change the setting.
•You can set a start time in the range of 1 to 60 minutes
in 1-minute increments.
Use D (+) and B (–) to change the setting.
•You can set a reset time in the range of 1 to 5 minutes
in 1-minute increments.
Press Dto toggle between the auto-repeat mode (ON)
and the elapsed time mode (OFF).
•An auto-repeat indicator ( ) appears when the auto-
repeat mode is selected.
Press D to toggle progress beeper on ( ) and off (ON OFF).
•A progress beeper indicator ( ) appears when this
setting is turned on.
4. Press A to exit the setting screen.
•The reset time setting must be less than the countdown start time setting.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To use the countdown timer
In the Countdown Timer Mode, press to start theD
countdown timer.
•The countdown timer measurement operation continues
even if you exit the Countdown Timer Mode.
•The table below describes button operations you can
perform to control countdown operations.
To do this:
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and display the reset time
Start the countdown from the displayed reset time
Do this:
Press D.
Press D again.
While the countdown is
stopped, press B.
Press .B
Press D.
Produkt Specifikationer
| Mærke: | Casio |
| Kategori: | Ur |
| Model: | 2926 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Casio 2926 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ur Casio Manualer
7 April 2025
7 April 2025
30 Marts 2025
22 December 2024
22 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
Ur Manualer
- Ur Just
- Ur Armani
- Ur Alpina
- Ur Sinn
- Ur McIntosh
- Ur Iron Annie
- Ur Profile
- Ur Balance
- Ur Ikea
- Ur Braun
- Ur Freestyle
- Ur Certina
- Ur So & Co
- Ur Pyle
- Ur Techno Line
Nyeste Ur Manualer
9 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025