Casio Collection W-212H-2AVES Manual

Casio Ur Collection W-212H-2AVES

Læs gratis den danske manual til Casio Collection W-212H-2AVES (2 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Casio Collection W-212H-2AVES, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Operation Guide 3149

4. While a setting is flashing, press D to increase it.

•To set an alarm that does not include a month (Daily alarm, Monthly alarm),

set x for the month. Press D until the x mark appears (between 12 and 1) while

month setting is flashing.

•To set an alarm that does not include a day (Daily alarm, 1-Month alarm),

set xx for the day. Press D until the

xx mark appears (between the end of the

month and 1) while the day setting is flashing.

•When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze

alarm, the alarm operation is performed a total of seven times, every five minutes, or

until you turn the alarm off or change it to a one-time alarm.

Note

•Pressing any button stops the alarm tone operation.

•Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the Alarm

setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn Alarms

through

on and off

1. In the Alarm Mode, use D to select a one-time alarm

(alarm number 2 through 5).

2. Press A to toggle the displayed alarm on and off.

•Turning on a one-time alarm (

2 through 5) displays the

one-time alarm on indicator on its screen.

•The one-time alarm on indicator is displayed in all

modes.

•If any alarm is on, the one-time alarm on indicator is

shown on the display in all modes.

To select the operation of Alarm

1. In the Alarm Mode, use D to select Alarm

2. Press A to cycle through the available settings in the sequence shown below.

Snooze alarm on indicator and one-time alarm on indicator

One-time alarm on Alarm offSnooze alarm on

•The applicable indicator is displayed in all modes when an alarm is turned on.

•The snooze alarm on indicator flashes during the 5-minute intervals between

alarms.

•Displaying the Alarm1 setting screen while the snooze alarm is turned on turns off

the snooze alarm automatically (making Alarm

1 a one-time alarm).

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

•You can configure Alarm1 as a snooze alarm or a one-time alarm. Alarms

through 5 can be used as one-time alarms only.

•The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash. This indicates the setting screen.

3. Press C to move the flashing in the sequence shown

below to select other settings.

Hour Minutes Month Day

Alarms

You can set five independent Daily Alarms. When an

alarm is turned on, the alarm tone sounds when the alarm

time is reached. One of the alarms can be configured as a

snooze alarm or a one-time alarm, while the other four are

one-time alarms.

You also can turn on an hourly time signal that causes the

watch to beep twice every hour on the hour.

•There are five alarm screens numbered

1 through 5.

The hourly time signal screen is indicated by

:00.

•When you enter the Alarm Mode, the screen you were

viewing when you last exited the mode appears first.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

Alarm Types

The alarm type is determined by the settings you make, as described below.

• Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

• Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

• 1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at time you set, only during the month you set.

• Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at time you set, on the day you set.

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Seconds Hour Minutes

Day Month Year

3. When the setting you want to change is flashing, press D to change it as

described below.

MA0804-EA

About This Manual

•Button operations are indicated using the letters shown

in the illustration.

•Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

Timekeeping Mode Alarm Mode Countdown Timer Mode Stopwatch Mode Dual Time Mode

Press .

General Guide

•Press C to change from mode to mode.

•In any mode, press B to illuminate the display.

•In any mode, hold down for about two seconds to return to the TimekeepingC

Mode.

Hour : Minutes Seconds

Day of week

PM indicator

Month – Day

To change this setting

Seconds

Hour, Minutes, Year, Month, Day

Perform this button operation

Press .D to reset to 00

Press D to increase the setting.

•Pressing while the seconds are in the range of 30 to 59 resets them to andD00

adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.

4. Press A to exit the setting screen.

•The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

•The year can be set in the range of 2000 to 2099.

•The watch’s built-in full automatic calendar automatically makes allowances for

different month lengths and leap years. Once you set the date, there should be no

reason to change it except after you have the watch’s battery replaced.

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press to toggle between 12-hour timekeeping andD

24-hour timekeeping.

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Hour : Minutes

One-time alarm on

indicator

Operation Guide 3149

Illumination

An LED (light-emitting diode) illuminate the display for

easy reading in the dark.

Illumination Precautions

•Illumination may be hard to see when viewed under

direct sunlight.

•Illumination turns off automatically whenever an alarm

sounds.

•Frequent use of illumination runs down the battery.

To illuminate the display

Press B to turn on illumination.

Dual Time

The Dual Time Mode lets you keep track of time in a different time zone.

•In the Dual Time Mode, the seconds count is synchronized with the seconds count

of the Timekeeping Mode.

To set the Dual Time

1. Press C to enter the Dual Time Mode.

2. In the Dual Time Mode, hold down A until the hour

setting starts to flash, which indicates the setting

screen.

3. Press C to change the selection in the following

sequence.

Hour Minutes

4. Press D to increase the setting.

5. Press A to exit the setting screen.

Countdown Timer

The countdown timer can be set within a range of

1 minute to 24 hours. An alarm sounds when the

countdown reaches zero.

•You can also select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

•Countdown timer functions are available in the

Countdown Timer Mode, which you enter by pressing

To use the countdown timer

Press D while in the Countdown Timer Mode to start the countdown timer.

•When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is automatically reset to its starting value after the alarm stops.

•Press D while a countdown operation is in progress to pause it. Press D again to

resume the countdown.

•To completely stop a countdown operation, first pause it (by pressing D), and then

press A. This returns the countdown time to its starting value.

To set the countdown start time

1. In the Countdown Timer Mode, hold down A until the

hours setting of the countdown start time starts to flash,

which indicates the setting screen.

2. Press C to move the flashing between the hours and

minutes settings.

3. While a setting is flashing, use D to change it.

•To set the starting value of the countdown time to

24 hours, set 0:00.

4. Press A to exit the setting screen.

To turn auto-repeat on and off

1. In the Countdown Timer Mode, hold down A until the

hours setting of the countdown start time starts to flash,

which indicates the setting screen.

2. Press B to toggle auto-repeat on (

AUTO REPEAT

displayed) and off (

AUTO REPEAT

not displayed).

•Note that pressing B in the above operation also turns

on the illumination.

•When the end of the countdown is reached while

auto-repeat is on, the alarm sounds, but the countdown

restarts from the beginning without stopping. You can

stop the countdown by pressing and manually resetD

to the start time by pressing A.

•The auto-repeat indicator appears in the Countdown

Timer Mode only.

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

•The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing .C

To measure times with the stopwatch

Elapsed time

Start Stop Re-start Stop Clear

Start Split

( displayed)SPL

Split release Stop Clear

Start Split Stop Split release Clear

Split time

Two Finishes

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

To turn the hourly time signal on and off

1. In the Alarm Mode, use D to select the hourly time

signal (:00).

2. Press A to toggle it on and off.

•Turning on the hourly time signal displays the hourly

time signal on indicator.

•The hourly time signal on indicator is displayed in all

modes when the hourly time signal is turned on.

Hour

Minutes

Seconds

Hourly time signal on

indicator

Auto-repeat indicator

1/100 second

Hour

Minutes

Seconds

Hour : Minutes Seconds

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Auto return features

•If you leave a screen with flashing digits for two or three minutes without performing

any operation, the watch automatically saves any settings you have made up to that

point and exits the setting screen.

Data and Setting Scrolling

The D button is used to scroll through setting screen data on the display. Holding

down this button during a scroll operation scrolls through the data at high speed.

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	Collection W-212H-2AVES

Har du brug for hjælp?

Hvis du har brug for hjælp til Casio Collection W-212H-2AVES stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ur Casio Manualer

Casio AE2000W-1AV Manual

5 September 2025

Casio AEQ-110 Manual

4 September 2025

Casio G-Shock GA-700UC-3A Manual

28 Juli 2025

Casio Baby-G BSA-B100 Manual

27 Juli 2025

Casio G-Shock GM-110 Manual

27 Juli 2025

Casio G-Shock GM-S5600 Manual

27 Juli 2025

Casio Edifice EF-527D-1A Manual

27 Juli 2025

Casio Edifice EFR-571 Manual

27 Juli 2025

Casio G-Shock GST-S110 Manual

27 Juli 2025

Casio Baby-G BGD-570 Manual

27 Juli 2025

Ur Manualer

Nyeste Ur Manualer

Grand Seiko 9F85 Manual

12 September 2025

Grand Seiko 9R01 Manual

11 September 2025

Grand Seiko 9R65 Manual

11 September 2025

Grand Seiko 9R02 Manual

11 September 2025

Grand Seiko 9R15 Manual

11 September 2025

Citizen Attesa Satellite Wave GPS Layers of Time CC4057-60E Manual

3 September 2025

Citizen L Mae EM1060-52N Manual

3 September 2025

Citizen Corso Diamond EW2712-55E Manual

3 September 2025

Citizen Attesa Radio Controlled Layers of Time AT8286-65E Manual

3 September 2025

Breitling AVI Ref. 765 1964 Re-Edition Manual

28 August 2025