Casio Collection W-96H-1AVES Manual

Casio Ur Collection W-96H-1AVES

Læs gratis den danske manual til Casio Collection W-96H-1AVES (2 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Casio Collection W-96H-1AVES, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Operation Guide 2499/3092

Alarm

The multi-function alarm lets you specify the hour,

minutes, month, and day for the alarm. You can set up the

alarm so it sounds once when the alarm time is reached,

or for a snooze alarm that repeats up to seven times,

every five minutes.

You can also turn on an Hourly Time Signal that causes

the watch to beep twice every hour on the hour.

• Pressing D in the Alarm Mode toggles between the

alarm screen (Alarm time displayed) and the Hourly

Time Signal screen (

:00 displayed).

• An alarm setting (and an Hourly Time Signal setting) is

available in the Alarm Mode, which you enter by

pressing .C

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

To set the time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to flash, which indicates the setting

screen.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Seconds Hour Minutes

Day Month Year

MA0702-EA

About This Manual

• The operational procedures for Modules 2499 and 3092 are identical. All of the

illustrations in this manual show Module 2499.

• Button operations are indicated using the letters shown in the illustration.

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

Module 2499 Module 3092

Timekeeping Mode Alarm Mode Stopwatch Mode Dual Time Mode

Press .

General Guide

• Press C to change from mode to mode.

• In any mode, press B to illuminate the display.

• In any mode, hold down for about two seconds to return to the TimekeepingC

Mode.

• In the Alarm, Stopwatch and Dual Time modes, the watch always shows the current

Timekeeping Mode time in the lower display area.

Hour : Minutes Seconds

Day of week

PM indicator

year Month – Da

3. When the setting you want to change is flashing, press D to change it as

described below.

To change this setting

Seconds

Hour, Minutes, Year, Month, Day

Perform this button operation

Press .D to reset to 00

Press D to increase the setting.

• Pressing while the seconds are in the range of 30 to 59 resets them to andD00

adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.

4. Press A to exit the setting screen.

• The day of the week is automatically displayed in accordance with the date (year,

month, and day) settings.

• The year can be set in the range of 2000 to 2099.

• The watch’s built-in full automatic calendar automatically makes allowances for

different month lengths and leap years. Once you set the date, there should be no

reason to change it except after you have the watch s battery replaced.’

To toggle between 12-hour and 24-hour timekeeping

In the Timekeeping Mode, press to toggle between 12-hour timekeeping andD

24-hour timekeeping.

• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Month Day–

Hour : Minutes

Alarm Types

The alarm type is determined by the settings you make, as described below.

• Daily alarm

Set the hour and minutes for the alarm time. This type of setting causes the alarm to

sound everyday at the time you set.

• Date alarm

Set the month, day, hour and minutes for the alarm time. This type of setting causes

the alarm to sound at the specific time, on the specific date you set.

• 1-Month alarm

Set the month, hour and minutes for the alarm time. This type of setting causes the

alarm to sound everyday at time you set, only during the month you set.

• Monthly alarm

Set the day, hour and minutes for the alarm time. This type of setting causes the alarm

to sound every month at time you set, on the day you set.

To set an alarm time

1. In the Alarm Mode, press D to display the alarm

screen.

2. Hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

• This operation automatically turns on the one-time

alarm.

3. Press C to move the flashing in the sequence shown

below to select other settings.

Hour Minutes Month Day

4. While a setting is flashing, press D to increase it.

• To set an alarm that does not include a month (Daily alarm, Monthly alarm),

set x for the month. Press D until the x mark appears (between 12 and 1) while

month setting is flashing.

• To set an alarm that does not include a day (Daily alarm, 1-Month alarm),

set xx for the day. Press D until the xx mark appears (between the end of the

month and 1) while the day setting is flashing.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for about 10 seconds. In the case of the

snooze alarm, the alarm repeats up to seven times every five minutes.

• Pressing any button stops the alarm tone operation.

• The alarm and the Hourly Time Signal sound in all modes.

To select the alarm type

1. In the Alarm Mode, press D to display the alarm

screen.

2. Press A to cycle through the available alarm settings

shown below.

One-time

alarm on

Alarm off

Snooze

alarm on

• The alarm on indicator and the snooze alarm on

indicator are shown on the display in all modes while

these functions are turned on.

• The snooze alarm on indicator flashes during the

5-minute intervals between alarms.

• Displaying the Alarm Mode setting screen automatically

changes the alarm type to one-time alarm.

• Changing the Timekeeping Mode setting screen during a 5-minute interval between

snooze alarms stops the current snooze alarm operation (but snooze alarm remains

as the alarm type setting).

• If a snooze alarm time is reached while you are setting the current time in the

Timekeeping Mode, the alarm sounds only once. Subsequent snooze alarm

operations are not performed.

Alarm on/off indicator

Operation Guide 2499/3092

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

• The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing .C

To measure times with the stopwatch

Elapsed time

Start Stop Re-start Stop Clear

Start Split

( displayed)SPL Split release Stop Clear

Start Split Stop Split release Clear

Split time

Two Finishes

First runner

finishes.

Display time of

first runner.

Second runner

finishes.

Display time of

second runner.

Dual Time

The Dual Time Mode lets you keep track of time in a different time zone.

• In the Dual Time Mode, the seconds count is synchronized with the seconds count

of the Timekeeping Mode.

To set the Dual Time

1. Press C to enter the Dual Time Mode.

2. In the Dual Time Mode, hold down A until the hour

setting starts to flash, which indicates the setting

screen.

3. Press C to change the selection in the following

sequence.

Hour Minutes

4. Press D to increase the setting.

5. Press A to exit the setting screen.

Stopping a Snooze Alarm Operation

After a snooze alarm time is reached, you can perform the following steps during any

5-minute interval between alarms to stop the snooze alarm operation.

To stop a Snooze Alarm Operation

1. While in the Alarm Mode, press D to display the alarm screen.

2. Next, press A to turn off the alarm or to select the one-time alarm.

• Note that this also changes the alarm type setting. If you want to use the snooze

alarm again, you must re-select it as the alarm type. See To select the alarm type“ ”

for more information.

To test the alarm

• In the Alarm Mode, hold down to sound the alarm.D

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, press D to display the Hourly Time Signal screen.

2. Press A to turn it on and off.

Indicates Hourly Time Signal is on.

Indicates Hourly Time Signal is off.

• The Hourly Time Signal on indicator is shown on the display in all modes while this

function is turned on.

1/100 second

Hour

Minutes

Seconds

Hour : Minutes Seconds

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Auto return features

• If you leave a screen with flashing digits for two or three minutes without performing

any operation, the watch automatically saves any settings you have made up to that

point and exits the setting screen.

Data and Setting Scrolling

The D button is used to scroll through setting screen data on the display. Holding

down this button during a scroll operation scrolls through the data at high speed.

Backlight Precautions

The backlight uses an LED (light-emitting diode) and a light guide panel that cause

the entire display to glow for easy reading in the dark.

In any mode, press to illuminate the display for about one second.B

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The backlight automatically stops illuminating whenever an alarm sounds.

• Frequent use of the backlight shortens the battery life.

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	Collection W-96H-1AVES

Har du brug for hjælp?

Hvis du har brug for hjælp til Casio Collection W-96H-1AVES stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ur Casio Manualer

Casio G-Shock GST-S110 Manual

27 Juli 2025

Casio Baby-G BGD-570 Manual

27 Juli 2025

Casio Edifice EFS-S510 Manual

27 Juli 2025

Casio Vintage A100WE-1AVT Manual

27 Juli 2025

Casio G-Shock GM-S5640 Manual

27 Juli 2025

Casio Baby-G MSG-S200 Manual

27 Juli 2025

Casio G-Shock GA-B001 Manual

27 Juli 2025

Casio Vintage A100 Manual

27 Juli 2025

Casio G-Shock GWG-2000 Manual

27 Juli 2025

Casio Vintage CA-500WEG Manual

27 Juli 2025

Ur Manualer

Nyeste Ur Manualer

Citizen Star Wars Darth Vader Tsuno AN3669-52E Manual

27 Juli 2025

Citizen Eco-Drive Brycen AW1598-70X Manual

27 Juli 2025

Citizen Star Wars Jedi Master BM7498-00W Manual

27 Juli 2025

Citizen Ladies' Dress EM0850-80D Manual

27 Juli 2025

Citizen Disney Princess Ariel GA1073-63W Manual

27 Juli 2025

Citizen Star Wars R2-D2 Tsuno AN3666-51A Manual

27 Juli 2025

Citizen Silhouette Chronograph FB1443-08A Manual

27 Juli 2025

Citizen Promaster Diver Super Titanium BN0200-56E Manual

27 Juli 2025

Citizen Disney Special Edition Mulan GA1057-01W Manual

27 Juli 2025

Citizen Eco-Drive Brycen BL556358E Manual

26 Juli 2025