Casio DW6600C-1V Manual

Casio Ur DW6600C-1V

Læs gratis den danske manual til Casio DW6600C-1V (1 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Casio DW6600C-1V, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

• Press to change from mode to mode.C

• In any mode, press to illuminate the display for about three seconds. The watch can be set so D

that the backlight flashes whenever an alarm sounds.

GENERAL GUIDE

21 3 4 5

Alarm Mode

21 3 4 5

Timekeeping Mode

[Modules 1199 & 1220][Module 1298]

C E C

21 3 4 5

Countdown Alarm Mode

21 3 4 5

Stopwatch Mode

The operational procedures for Modules

1199, 1220, and 1298 are identical. All of the

illustrations in this manual show Modules

1199 and 1220.

Minutes Seconds

21 3 4 5

Mode indicator

Current time

Minutes seconds 1/10 second

The countdown timer can be set within a range of 1 second to 60

minutes. When the countdown reaches zero, an alarm sounds for

10 seconds or until you press any button.

To set the countdown time

1. Press A while in the Countdown Alarm Mode. The minutes

digit flashes on the display because it is

selected

2. Press C to change the selection in the following sequence.

3. Press E to increase the selected number or to decrease it. Holding down either buttonB

changes the selection at high speed.

4. After you set the countdown time, press A to return to the Countdown Alarm Mode.

To use the countdown timer

1. Press E while in the Countdown Alarm Mode to start the countdown timer.

2. Press E again to stop the countdown timer.

• You can continue countdown timer operation by pressing .E

3. Stop the timer and then press B to reset the countdown time to its starting value.

• The countdown time is automatically reset to its starting value after the alarm stops.

This watch is equipped with a backlight that can be set to flash

whenever an alarm sounds. For details, see “About the backlight”.

• In the Timekeeping Mode, press to switch between the 12-E

hour and 24-hour formats.

• In the Timekeeping Mode, the Graphic Display indicates the

counting of seconds.

To set the time and date

1. Press A while in the Timekeeping Mode. The seconds digits

flash on the display because they are

selected

2. Press C to change the selection in the following sequence.

TIMEKEEPING MODE

3. While the seconds digits are selected (flashing), press to reset the seconds to “00”. If you pressE

E while the seconds count is in the range of 30 to 59, the seconds are reset to “00” and 1 is added

to the minutes. If the seconds count is in the range of 00 to 29, the minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press E to increase the number

or B to decrease it. While the day of the week is selected, pressing advances to the next dayE

and B goes to the previous day. Holding down either button changes the current selection at high

speed.

5. After you set the time and date, press A to return to the Timekeeping Mode.

• The watch does not make any allowance for leap years. Be sure to manually set February 29

(when one occurs) to the appropriate date.

• If you do not operate any button for a few minutes while a selection is flashing, the flashing stops

and the watch goes back to the Timekeeping Mode automatically.

Module No. 1199/1220/1298

21 3 4 5

Month

Date

Hour Seconds

PM indicator

Graphic display

Minutes

Day of week

HourSeconds Minutes

MonthDate

Day of

Week

About the backlight

When you switch the backlight function on, the backlight of the watch flashes whenever a daily alarm

or countdown alarm is sounding, or when various signals are sounded in the Stopwatch and Alarm

Modes. For details of each of these operations, see the applicable sections of this manual.

• The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating

power after very long term use.

To switch the backlight function on and off

In the Timekeeping Mode, hold down B for one or two seconds to switch the backlight function on

and off.

• The backlight function indicator remains on the display in all modes.

• The above operation controls operation of the backlight function only. It does not affect operation

of audible tones and signals.

• Pressing D at any time illuminates the display for about three seconds, regardless of the

backlight’s on/off setting.

• The watch will emit an audible sound whenever the display is illuminated. This is caused by a

transistor that vibrates when the EL panel lights up. It does not indicate malfunction of the watch.

When the Daily Alarm is switched on, the alarm sounds for 20

seconds at the preset time each day. Press any button to stop the

alarm after it starts to sound.

When the Hourly Time Signal is switched on, the watch beeps

every hour on the hour.

To set the alarm time

1. Press A while in the Alarm Mode. The hour digits flash on the

display because they are

selected

• At this time the Daily Alarm is switched on automatically.

2. Press C to change the selection in the following sequence.

3. Press E to increase the selected digits and to decrease them. Holding down either buttonB

changes the selection at high speed.

• The format (12-hour and 24-hour) of the alarm time matches the format you select for normal

timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the time correctly as

morning or afternoon (P) .

4. After you set the alarm time, press to return to the Alarm Mode.A

To switch the Daily Alarm and Hourly Time Signal on and off

Press B while in the Alarm Mode to change the status of the Daily Alarm and Hourly Time Signal

in the following sequence.

ALARM MODE

Minutes

Hour

21 3 4 5

Backlight

function

indicator

OFFON

21 3 4 5

Hourly time signal on indicator

Hour Minutes

Current time

Mode indicator

Alarm on indicator

To test the alarm

Hold down E while in the Alarm Mode to sound the alarm.

[Alarm ON Indicator/Hourly Time Signal ON Indicator]

Both ON Both OFF Daily Alarm

Only

Hourly Time

Signal only

Daily Alarm

only

COUNTDOWN ALARM MODE

STOPWATCH MODE

21 3 4 5

CDE

Minutes 1/100 second

Mode indicator Hours

Seconds

The Stopwatch Mode lets you measure elapsed time, split times,

and two finishes. You also get Auto-Start and Target Time

functions. The range of the stopwatch is 23 hours, 59 minutes,

59.99 seconds.

To measure elapsed time

1. Press E to start the stopwatch.

2. Press E to stop the stopwatch.

• You can resume the measurement operation by pressing E

again.

3. Press B to clear the stopwatch to all zeros (0H 00'00"00).

To record split times

1. Press E to start the stopwatch.

2. Press B to display the timing up to that point. Stopwatch timing continues internally.

3. Press B to clear the split time and to continue time measurement on the display.

• You can repeat steps 2 and 3 as many times as you want.

4. Press E to stop the time measurement.

5. Press B to clear the stopwatch to all zeros.

To time first and second place finishes

1. Press E to start the stopwatch.

2. Press B when the first finisher crosses the line, and record the time.

3. Press E when the second finisher crosses the line.

4. Press B to display the finishing time of the second finisher.

5. Press B again to clear the stopwatch to all zeros.

About the Auto-Start function

With the Auto-Start function, the watch performs a 5-second countdown. When the countdown

reaches zero, stopwatch operation starts automatically. During the final three seconds of the

countdown, a beeper sounds with each second.

To use the Auto-Start function

1. While the display is showing all zeros (0H00'00"00) in the

Stopwatch Mode, press .B

• The upper display shows a count of 5 seconds, which is the

starting value of the Auto-Start countdown.

2. Press E to start the countdown. When the countdown

reaches zero, the watch emits a long beep and the stopwatch

begins operation.

• To stop the Auto-Start countdown and return to the initial

countdown display, press .B

• Pressing E while the Auto-Start countdown is in progress

immediately starts the stopwatch.

About the Target Time function

With the Target Time function, an alarm sounds for five seconds whenever the time being kept by

the stopwatch reaches a target time you have preset. To activate the Target Time function, simply

set a target time. The function is automatically deactivated whenever the target time is set to

0H00'00".

To set the Target Time

1. While the display is showing all zeros (0H00'00"00) in the

Stopwatch Mode, press , and the hours digit of the targetA

time starts to flash. It flashes because it is

selected

• You can also press in the above procedure after pressing A B

to display the Auto-Start countdown time.

2. Press C to change the selection in the following sequence.

3. While any number is selected (flashing), press to increase it or to decrease it. Holding downE B

either button changes the current selection at high speed.

• The maximum target time setting is 23 hours, 59 minutes, 59 seconds.

• Press and at the same time to reset the target time to 0H00'00".B E

4. After you set the target time, press A to return to the Stopwatch Mode.

• The Target Time Indicator (TARGET) is appears on the display in the Stopwatch Mode whenever

a target time is preset.

21 3 4 5

Target time indicator

Hours SecondsMinutes

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	DW6600C-1V
Bredde:	48.9 mm
Dybde:	42.8 mm
Højde:	13.4 mm
Vægt:	54 g
Armbånd, materiale:	Resin
Vandfast:	Ja
Kalender:	Ja
Ur-indstilling:	12t/24t
Stopur:	Ja
Urtype:	Armbåndsur
Batterilevetid:	2 År
LED-baggrundsbelysning:	Ja
Batteritype:	CR2016
Slagfast:	Ja
Produktdesign:	Sport
Mekanismetype:	Elektronisk
Vandbestandig dybde:	200 m
Husets farve:	Sort
Båndets hovedfarve:	Sort
Etui form:	Rund
Hovedfarve på urskive:	Grå
Se markørfarve:	Sort
Køn:	Hanstik
Nøjagtighed:	15 sek/md
Se markørstil:	Arabisk nummervisning
Kronograf:	Ingen
Nedtællingsur:	Ja