Casio Edifice EQW-M1000DB-1AER Manual

Casio Ur Edifice EQW-M1000DB-1AER

Læs gratis den danske manual til Casio Edifice EQW-M1000DB-1AER (6 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Casio Edifice EQW-M1000DB-1AER, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
1
Operation Guide 5061
MA0910-EB
Congratulations upon your selection of this CASIO watch.
This watch does not have a city code that corresponds to the UTC offset of –3.5
hours. Because of this, the radio-controlled atomic timekeeping function will not
display the correct time for Newfoundland, Canada.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
or loss suffered by you or any third party arising through the use of this product or
its malfunction.
About This Manual
Button operations are indicated using the letters A
through shown in the illustration.D
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand: Indicates the current mode.
b Lower Dial Hand
n Right Dial Hands: Indicate a time, in 24-hour format,
depending on the current mode.
m Day
This User’s Guide uses numbers shown above to identify
watch hands and indicators.

B +
* 6> 5
@
Things to check before using the watch
1. Hold down for about two seconds to enter the Timekeeping Mode, and C
then observe the movement of the
x .Second Hand
2. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To configure Home City settings” to configure your Home
City and daylight saving time settings.
Important!
Proper time calibration signal reception and World Time settings depend on correct
Home City, time, and date settings in the Timekeeping Mode. Make sure you
configure these settings correctly.
3. Set the current time.
To set the time using a time calibration signal •
See “To get ready for a receive operation”.
To set the time manually •
See “Configuring Current Time and Date Settings Manually”.
The watch is now ready for use.
For details about the watch’s radio controlled timekeeping feature, see “Radio •
Controlled Atomic Timekeeping”.
Is the moving smoothly in one-second steps?xSecond Hand
Is the jumping every two xSecond Hand
seconds or is it stopped completely?
Go to step 2.
The watch is charged sufficiently.
For details about charging, see
“Charging the Watch”.
Power is low. Charge the watch by placing
it in a location where it is exposed to light.
For details, see “Charging the Watch”.
NO
YES
YES
NEXT
Charging the Watch
The face of the watch is a solar cell that generates power from light. The generated
power charges a built-in rechargeable battery, which powers watch operations. The
watch charges whenever it is exposed to light.
Charging Guide
Whenever you are not
wearing the watch, be sure
to leave it in a location
where it is exposed to light.
Best charging •
performance is achieved
by exposing the watch to
light that is as strong as
possible.
When wearing the watch,
makes sure that its face is
not blocked from light by the
sleeve of your clothing.
The watch may enter a •
sleep state if its face is
blocked by your sleeve
even only partially.
Warning!
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become
particularly hot when exposed to the following conditions for long periods.
On the dashboard of a car parked in direct sunlight •
Too close to an incandescent lamp •
Under direct sunlight •
Important!
Keep the watch in an area normally exposed to bright light when storing it for long •
periods. This helps to ensure that power does not run down.
Storing the watch for long periods in an area where there is no light or wearing it in •
such a way that it is blocked from exposure to light can cause power to run down.
Make sure that the watch is exposed to bright light whenever possible.
Power Levels
You can get an idea of the watch’s power level by
observing the movement of the
x in the Second Hand
Timekeeping Mode.
If the •x is moving normally in one-second Second Hand
steps, power is at Level 1.
If the •x is jumping at two-second steps, Second Hand
power is at Level 2, which is quite low. Expose the watch
to light as soon as possible so it can charge.

B +

@5
Jumps every two seconds.
Level Hand Movement Function Status
1 Normal. All functions enabled.
2x jumps in 2-second steps.Second hand
m changes to home position.Day
Beeper, time calibration signal
reception, and countdown timer
operation disabled.
3
x stopped.Second hand
z and stopped at Hour cMinute hands
12 o’clock.
All functions disabled.
When power drops to Level 3, all functions will be disabled but the watch will •
continue to keep time internally for about one week. If you recharge the battery
sufficiently during this period, the analog hands will move automatically to the
correct setting and normal timekeeping will resume. After one week, all settings
(including timekeeping) will be cleared. Recharging the battery will reset all settings
to their initial factory defaults.
Power Recovery Mode
The watch is designed to go into a power recovery mode that stops hand operation
temporarily whenever power suddenly drops below a certain level due to overuse
of the alarm tone over a short period. Note that all operations are disabled while the
watch is in the power recovery mode.
The hands will move to the correct positions and the watch will resume normal
operation after power recovers (in about 15 minutes). Putting the watch in a location
where it is exposed to light will help power to recover sooner.
Charging Times
Exposure Level (Brightness)
Daily
Operation
*1
Level Change *2
Level 3 Level 2 Level 1
Outdoor sunlight (50,000 lux) 8 min. 2 hours 23 hours
Sunlight through a window (10,000 lux) 30 min. 6 hours 85 hours
Daylight through a window on a cloudy
day (5,000 lux) 48 min. 8 hours 138 hours
Indoor fluorescent lighting (500 lux) 8 hours 92 hours – – –
1 Approximate amount exposure time required each day to generate enough power *
for normal daily operation.
2 Approximate amount exposure time required to take power from one level to the *
next.
The above exposure times all are for reference only. Actual exposure times depend •
on lighting conditions.
For details about the operating time and daily operating conditions, see the “Power •
Supply” section of the Specifications.
Power Saving
Power Saving enters a sleep state automatically whenever the watch is left for a
certain period in an area where it is dark. The table below shows how watch functions
are affected by Power Saving.
There actually are two sleep state levels: “second hand sleep” and “function sleep”. •
Elapsed Time in Dark Operation
60 to 70 minutes (second hand
sleep)
x only is stopped at 12 o’clock, all other Second hand
functions are enabled.
6 or 7 days (function sleep) All functions, including analog timekeeping, disabled •
Internal timekeeping maintained. •
The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch •
is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep
state.
The watch will not enter a sleep state while it is in the Stopwatch Mode or •
Countdown Timer Mode.
To recover from the sleep state
Move the watch to a well-lit area or press any button.
2
Operation Guide 5061
Radio Controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly.
However, when using the watch outside of areas covered by time calibration signals,
you will have to adjust the settings manually as required. See “Configuring Current
Time and Date Settings Manually” for more information.
This section explains how the watch updates its time settings when the city code
selected as the Home City is in Japan, North America, Europe, or China, and is one
that supports time calibration signal reception.
If your Home City Code setting is this: The watch can receive the signal from
the transmitter located here:
LONDON (LON), PARIS (PAR), ATHENS (ATH) Anthorn (England), Mainflingen (Germany)
HONG KONG (HKG) Shangqiu City (China)
TOKYO (TYO) Fukushima (Japan), Fukuoka/Saga (Japan)
HONOLULU (HNL), ANCHORAGE (ANC),
LOS ANGELES (LAX), DENVER (DEN),
CHICAGO (CHI), NEW YORK (NYC)
Fort Collins, Colorado (United States)
Important!
The areas covered by •HONOLULU HNL ANCHORAGE ANC( ) and ( ) are quite far
from the calibration signal transmitters, so certain conditions may cause reception
problems.
When •HONOLULU HNL HONG KONG HKG( ) or ( ) is selected as the Home City,
only the time and date are adjusted according to the time calibration signal. You
need to switch manually between standard time and daylight saving time (DST) if
required. See “To toggle the Home City time between standard time and daylight
saving time” for information about how to do this.
Approximate Reception Ranges
Even when the watch is within range of a transmitter, signal reception may be •
impossible due to the effects of geographic contours, structures, weather, the time
of year, the time of day, radio interference, etc. The signal becomes weaker at
distances of approximately 500 kilometers, which means that the influence of the
conditions listed above becomes even greater.
Signal reception may not be possible at the distances noted below during certain •
times of the year or day. Radio interference may also cause problems with
reception.
Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310
miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 500 kilometers (310 miles)
As of January 2008, China does not use Daylight Saving Time (DST). If China does •
go to the Daylight Saving Time system in the future, some functions of this watch
may no longer operate correctly.
To get ready for a receive operation
Confirm that the watch is in the Timekeeping Mode. If it isn’t, hold down 1. for C
about two seconds to enter the Timekeeping Mode.
Place the watch in a location where signal reception is good.2.
Position the watch as shown in the •
nearby illustration, with 12 o’clock
pointed towards a window. Make
sure there are no metal objects
nearby.
Signal reception normally is better •
at night.
The receive operation takes from •
two to seven minutes, but in some
cases it can take as long as 14
minutes. Take care that you do not
perform any button operation or
move the watch during this time.
UK and German Signals
Anthorn
500 kilometers
1,500 kilometers
Mainflingen
The Anthorn signal is receivable
within this area.
North American Signal
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
Fort Collins
Japanese Signal
Fukushima
500 kilometers
1,000 kilometers
Fukuoka/Saga
Chinese Signal
1,500 kilometers
Changchun500 kilometers
Beijing
Shangqiu
Shanghai
Chengdu
Hong Kong
12 o’clock
or
Signal reception may be difficult or even impossible under the conditions •
described below.
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
office
equipment,
or a mobile
phone
Near a
construction
site, airport,
or other
sources of
electrical
noise
Near
high-tension
power lines
Among
or behind
mountains
What you should do next depends on whether you are using Auto Receive or 3.
Manual Receive.
Auto Receive: Leave the watch over night in the location you selected in step 2. •
See “Auto Receive” for details.
Manual Receive: Perform the operation under “To perform manual receive”. •
Auto Receive
With Auto Receive, the watch performs the receive operation each day •
automatically up to six times (up to five times for the Chinese calibration signal)
between the hours of midnight and 5 a.m. (according to the Timekeeping Mode
time). When any receive operation is successful, none of the other receive
operations for that day are performed.
When a calibration time is reached, the watch will perform the receive operation •
only if it is in the Timekeeping Mode or World Time Mode. The receive operation is
not performed if a calibration time is reached while you are configuring settings.
To perform manual receive
In the Timekeeping Mode, keep 1. depressed (for about two seconds) as the A
x goes through the following sequence.Second Hand
Moves to the last signal reception result ( •Y N READY R or ), then to (or for some
models).
The 2. x indicates the operations the watch is currently performing.Second Hand
When the xSecond
Hand is pointed here: It means this:
READY (R) Watch is setting up for reception.
WORK (W) Reception is in progress.
YES (Y) Reception was completed
successfully.
NO (N) Reception failed for some reason.
If signal reception is unstable, the •x Second Hand
may move between and .WORK READY
The receive operation is complete when the 3. x Second
Hand moves to ( ) or ( ) for about five YES Y NO N
seconds, and then resumes normal timekeeping.
When the receive operation is successful, the watch •
adjusts the time setting accordingly. It does not adjust
the setting if the operation failed.
Note
To interrupt a receive operation and return to the •
Timekeeping Mode, press any button.
If the •x is pointing to ( ) or Second Hand YES Y NO
( ), you can return to the Timekeeping Mode by N
pressing .A
To check the result of the latest receive operation
In the Timekeeping Mode, press .A
The •x will move to ( ) for five Second Hand YES Y
seconds if the latest receive operation was successful,
or ( ) if it was not. After that, normal timekeeping NO N
will resume.
Note
The •x will indicate ( ) if you have Second Hand NO N
adjusted the time or date setting manually since the
latest receive operation.
If the •x is pointing to ( ) or ( ), Second Hand YES Y NO N
you can return to the Timekeeping Mode by pressing .A
Radio-controlled Atomic Timekeeping Precautions
Strong electrostatic charge can result in the wrong time setting. •
Even if a receive operation is successful, certain conditions can cause the time •
setting to be off by up to one second.
The watch is designed to update the date and day of the week automatically for •
the period January 1, 2000 to December 31, 2099. Updating of the date by signal
reception will no longer be performed starting from January 1, 2100.
If you are in an area where signal reception is not possible, the watch keeps time •
with the precision noted in “Specifications”.
The receive operation is disabled under any of the following conditions. •
While power is at Level 2 or lower −
While the watch is in the power recovery mode −
When the watch is in the function sleep state (power saving) −
While a countdown time operation is in progress −
A receive operation is cancelled if an alarm sounds while it is being performed. •


@

@

@

Produkt Specifikationer

Mærke: Casio
Kategori: Ur
Model: Edifice EQW-M1000DB-1AER

Har du brug for hjælp?

Hvis du har brug for hjælp til Casio Edifice EQW-M1000DB-1AER stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ur Casio Manualer

Casio

Casio AE2000W-1AV Manual

5 September 2025
Casio

Casio AEQ-110 Manual

4 September 2025
Casio

Casio G-Shock GA-700UC-3A Manual

28 Juli 2025
Casio

Casio Baby-G BSA-B100 Manual

27 Juli 2025
Casio

Casio G-Shock GM-110 Manual

27 Juli 2025
Casio

Casio G-Shock GM-S5600 Manual

27 Juli 2025
Casio

Casio Edifice EF-527D-1A Manual

27 Juli 2025
Casio

Casio Edifice EFR-571 Manual

27 Juli 2025
Casio

Casio G-Shock GST-S110 Manual

27 Juli 2025
Casio

Casio Baby-G BGD-570 Manual

27 Juli 2025

Ur Manualer

Nyeste Ur Manualer

Grand Seiko

Grand Seiko 9F85 Manual

12 September 2025
Grand Seiko

Grand Seiko 9R01 Manual

11 September 2025
Grand Seiko

Grand Seiko 9R65 Manual

11 September 2025
Grand Seiko

Grand Seiko 9R02 Manual

11 September 2025
Grand Seiko

Grand Seiko 9R15 Manual

11 September 2025
Citizen

Citizen Attesa Satellite Wave GPS Layers of Time CC4057-60E Manual

3 September 2025
Citizen

Citizen L Mae EM1060-52N Manual

3 September 2025
Citizen

Citizen Corso Diamond EW2712-55E Manual

3 September 2025
Citizen

Citizen Attesa Radio Controlled Layers of Time AT8286-65E Manual

3 September 2025
Breitling

Breitling AVI Ref. 765 1964 Re-Edition Manual

28 August 2025