Casio EFA119BK-1A Manual

Casio Ur EFA119BK-1A

Læs gratis den danske manual til Casio EFA119BK-1A (4 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Casio EFA119BK-1A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Operation Guide 4334

MO0607-EB

Warning!

• The measurement functions built into this watch are not intended for use in taking

measurements that require professional or industrial precision. Values produced

by this watch should be considered as reasonably accurate representations only.

• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any

claims by third parties that may arise through the use of this watch.

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully. About This Manual

• Button operations are indicated using the letters shown

in the illustration.

• For the sake of simplicity, the sample displays in this

manual do not show the analog hands of the watch.

• Depending on the model of your watch, display text

appears either as dark ﬁgures on a light background, or

light ﬁgures on a dark background. All sample displays

in this manual are shown using dark ﬁgures on a light

background.

• Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

(Light)

General Guide

• Press C to change from mode to mode.

• In any mode, press L to illuminate the display.

Recall Mode

World Time Mode

Stopwatch Modes

▲

Countdown Timer

Mode

▲

Alarm Mode

Press C.

▲

Hand Setting Mode

TimeKeeping Mode

▲

This watch has two

stopwatch modes. See

“Stopwatches” for more

information.

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

This watch features separate digital and analog

timekeeping. The procedures for setting the digital time

and analog time are diﬀerent.

• See “Thermometer” for details about the thermometer.

Setting the Digital Time and Date

This watch is preset with UTC diﬀerential values that

represent each time zone around the globe. Before setting

the digital time, be sure to first set the UTC differential for

your Home Time, which is the location where you normally

will be using the watch.

• Note that World Time mode times are all displayed

based on the time and date settings you conﬁgure in the

Timekeeping Mode.

PM indicator

Hour : Minutes

Seconds

Month – Day

Thermometer

Day of week

To set the digital time and date

1. In the Timekeeping Mode, hold down A until the

seconds start to ﬂash, which indicates the setting

screen.

• Be sure to conﬁgure the correct UTC diﬀerential for

your Home Time before conﬁguring any other

Timekeeping Mode settings.

• See the “UTC Differential/City Code List” for

information about the UTC diﬀerential settings that are

supported.

2. Press C to move the ﬂashing in the sequence shown

below to select other settings.

Seconds

Hour

UTC

Diﬀerential Minutes

Year

DST

Day Month

Seconds

Temperature

Unit

12/24-Hour

Format

Temperature Sensor

Calibration

Screen: To do this:

Reset the seconds to 00

Toggle between Daylight Saving

Time (ON OF) and Standard Time ( )

Specify the UTC diﬀerential

Change the hour or minutes

Toggle between 12-hour ( ) and12H

24-hour ( ) timekeeping2 H4

Do this:

Press D.

Use D (+) and B (–).

Press D.

Use D (+) and B (–).Change the year

Change the month or day

3. When the setting you want to change is flashing, use D

and B

to change it as

described below.

• The UTC diﬀerential setting range is –12.0 to +14.0, in 0.5-hour units.

• For information about settings other than the time and date, see the following.

Temperature Sensor Calibration: “Thermometer”

Temperature Unit: “Thermometer”

4. Press A to exit the setting screen.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all modes.

• The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

• When DST is turned on, the UTC diﬀerential setting range is –11.0 to +15.0, in 0.5-

hour units.

• Any time the seconds setting is changed, the analog hands are adjusted accordingly.

• See “Daylight Saving Time (DST) Setting” below for details about the DST setting.

Daylight Saving Time (DST) Setting

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To toggle the Timekeeping Mode digital time between DST and Standard Time

1.In the Timekeeping Mode, hold down until theA

seconds start to ﬂash, which indicates the setting

screen.

2. Press once and the DST setting screen appears.C

3. Press to toggle between Daylight Saving Time (D ON

displayed) and Standard Time (OF displayed).

4. Press to exit the setting screen.A

• The DST indicator appears on the Timekeeping, Alarm,

and Hand Setting Mode screens to indicate that

Daylight Saving Time is turned on.

Setting the Analog Time

Perform the procedure below when the time indicated by the analog hands does not

match the time of the digital display.

DST indicator

On/Off status

To adjust the analog time

1. In the Timekeeping Mode, press C six times to enter

the Hand Setting Mode.

2. Hold down A until the current digital time starts to

ﬂash, which indicates the setting screen.

3. Use to adjust the analog setting.D

• Press Donce to advance the hands 20 seconds.

• Hold down D to advance the hands at high speed.

• To lock high speed hands movement, hold down D B to start it and then press

to lock. The hands will continue to advance for one 12-hour cycle or until you

press any button to stop it.

High-speed hand movement also will stop automatically after the time advances

12 hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper)

starts to sound.

4. Press A to exit the setting screen.

• The minute hand will be adjusted slightly to match the seconds when you exit the

setting screen.

• To return to the Timekeeping Mode, press C.

Stopwatches

Your watch has two stopwatch modes: a Single Stopwatch

Mode and a Dual Stopwatch Mode. Both stopwatch

modes measure times in 1/100-second units for the ﬁrst

hour, and in 1-second units after that. In both stopwatch

modes, timing is possible up to 99 hours, 59 minutes,

59.99 seconds.

The Single Stopwatch Mode (ST1) displays the total

elapsed time and lap times for a single vehicle or runner.

The Dual Stopwatch Mode (ST2) can be used to measure

elapsed time for two vehicles or runners at the same time,

including separate lap times and the time diﬀerential

between vehicles or runners.

The data produced by either stopwatch mode is stored

automatically in watch memory, for later recall when you

need it.

• When the elapsed time being kept by either of the stopwatches exceeds 99 hours,

59 minutes, 59.99 seconds, the displayed time returns to all zeros and time

measurement continues from there. Elapsed time measurement continues until you

reset it to all zeros.

• All of the operations in this section are performed in the stopwatch modes, which

you enter by pressing C.

Operation Guide 4334

To select the Single Stopwatch Mode or Dual Stopwatch Mode

In the Stopwatch Mode, press A to toggle the Single Stopwatch Mode and the Dual

Stopwatch Mode.

• You cannot toggle between the Single Stopwatch Mode and Dual Stopwatch Mode

while an elapsed time operation is in progress.

After pressing to reset the elapsed time to all zeros, press again to toggleA A

between stopwatch modes.

• The indicator “

ST1” indicates the Single Stopwatch Mode, while indicates“ ”ST2

the Dual Stopwatch Mode.

Remaining free records

Single Stopwatch

Mode Screen

Dual Stopwatch

Mode Screen

Press .A

▲

• Both the Single Stopwatch Mode screen and the Dual Stopwatch Mode screen show

the number of free memory records available for storing data. The watch’s memory

can hold up to 50 records total, including both Single Stopwatch Mode and Dual

Stopwatch Mode records.

Using the Single Stopwatch Mode

The Single Stopwatch Mode displays the total elapsed time and lap times for a single

vehicle or runner.

Stopwatch mode indicator

To perform a Single Stopwatch Mode operation

1. While the Single Stopwatch Mode screen is displayed,

press D to start elapsed time measurement.

2. To display a lap time, press D while elapsed time

measurement is in progress.

• After about 10 seconds, the upper display will change

automatically to timing of the next lap, with the total

elapsed time shown in the lower display.

• Each press of D during elapsed time measurement

stores the applicable lap number, lap time, and total

elapsed time in memory.

• Lap numbers are displayed in the range of 01 to 99.

After lap 99, pressing does not display a lap timeD

(elapsed time continues without stopping).

• During the first hour, the stopwatch displays elapsed time in minutes, seconds,

and 1/100 second. After the first hour, the display changes to shows hours,

minutes, and seconds.

• Use the Recall Mode to view data in memory.

3. To stop elapsed time measurement and reset, press A.

Total elapsed time

Lap number

Lap time

Using the Dual Stopwatch Mode

The Dual Stopwatch Mode can be used to measure elapsed time for two vehicles or

runners at the same time, including separate lap times and the time differential

between vehicles or runners.

To perform a Dual Stopwatch Mode operation

The table below shows how to time two vehicles or

runners (Measurement A and Measurement B).

• The lower display shows Measurement A, while the

upper display shows Measurement B.

• In the Dual Stopwatch Mode, you can start timing from

either Measurement A or Measurement B.

Measurement B

Measurement A

• The lap number for the current displayed lap time (A or

B) appears in the center left of the display, and the

applicable lap time appears in the upper or lower display.

The other display (upper or lower) shows elapsed time

measurement.

• After about 10 seconds, the display will change

automatically to timing of the next lap.

• Each press of D B or during elapsed time

measurement stores the applicable lap number and lap

time in memory.

Measurement B Lap Time

Lap number

Measurement A Lap Time

Lap time screen

Start first

elapsed

time.

Press D.

Press B.

Display

lap time

screen.

Press D.

Press .B

Start other

elapsed

time.

Press B.

Press D.

Measurement A

Measurement B

Display lap

time of other

elapsed time.

Press B.

Press D.

Reset

elapsed

time to all

zeros.

Press .A

• Lap numbers are displayed in the range of 01 to 99.

After lap 99, pressing does not display a lap timeD

(elapsed time continues without stopping).

• After starting Measurement A or Measurement B

elapsed time measurement and then starting the other

time's elapsed time measurement displaying a lap time

for one of the times will display the other time's lap time

and the difference between Measurement A and

Measurement B. After about 5 seconds, the display will

change automatically to timing of the next lap.

• After you press one of the buttons to display one of the

lap times (without the lap time differential displayed),

pressing the other button displays the other lap time and

the differential between the two laps for about five

seconds.

• The ± indicator on the lap time differential screen“ ”

indicates both times are for the same lap.

• -'--"--“ ” is shown for the lap time differential if it is greater

than 10 minutes.

Measurement B

Lap Time

Measurement A and

Measurement B

differential

• Pressing A stops elapsed time measurement and reset.

• During the first hour, the stopwatch displays elapsed time in minutes, seconds, and

1/100 second. After the first hour, the display changes to shows hours, minutes, and

seconds.

• Use the Recall Mode to view data in memory.

Recalling Stopwatch Data

You can use the Recall Mode to recall and delete

stopwatch data stored in memory.

• Your watch automatically creates logs for storage of

stopwatch data in memory. For information about using

logs, see “Managing Memory Data”.

To recall stopwatch log data

1. Enter the Recall Mode.

• The title screen of the newest log appears first when

you enter the Recall Mode.

2. Use the button to scroll through log title screensA

until the one for the log you want to view is on the

display.

• Logs are numbered from 01 (oldest) to 50.

3. Press (+) or ) to view the log data.D B (–

Log number

Log title screen

Log creation

date

Stopwatch mode in

which the recalled

log data was

measured

Press .B

Press D.

▲

Best lap indicator Lap number of

best lap

Best lap

▲

Lap time

Lap number

▲

Total elapsed time

Recalled log data measured in the Single Stopwatch Mode (ST1)

Press B.

Press D.

▲

Recalled log data measured in the Dual Stopwatch Mode (ST2)

▲

Lap timeLap number

Lap time

Best lap indicator

Best lap

(Measurement A)

Best lap

(Measurement B)

▲

One second

later

Lap number of best lap

(Measurement B)

Lap number of best lap

(Measurement A)

*The best lap time is for the best time in the newest log only. The Best Lap Time

screen is the one that has the best lap indicator.

To delete stopwatch data

1. In the Recall Mode, use to scroll through log title screens until the one for the logA

you want to delete is on the display.

• Displaying lap time data (not the log title screen), deleting the data also will delete

the log that contains the data.

2. Hold down and until the watch beeps and B D “CLR” stops flashing on the

display.

• This will delete all of the data in the currently selected log.

• Deleting the newest log also will delete the best lap time data.

Countdown Timer

You can set the countdown timer within a range of one

minute to 100 hours. An alarm sounds when the

countdown reaches zero.

• You also can select auto-repeat, which automatically

restarts the countdown from the original value you set

whenever zero is reached.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Second

Hours Minutes

To use the countdown timer

Press while in the Countdown Timer Mode to start the countdown timer.D

• When the end of the countdown is reached and auto-repeat is turned off, the alarm

sounds for 10 seconds or until you stop it by pressing any button. The countdown

time is reset automatically to its starting value after the alarm stops.

• When auto-repeat is turned on, the countdown will restart automatically without

pausing when it reaches zero. The alarm sounds when the countdown reaches zero.

• The countdown timer measurement operation continues even if you exit the

Countdown Timer Mode.

• To stop a countdown operation completely, first pause it (by pressing ), and thenD

press A. This returns the countdown time to its starting value.

To configure countdown start time and auto-repeat settings

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the hour

setting of the countdown start time starts to flash, which

indicates the setting screen.

• If the countdown start time is not displayed, use the

procedure under To use the countdown timer“ ” to

display it.

2. Press C to move the flashing in the sequence shown

below, and select the setting you want to change.

Start Time

(Minutes)

Auto-Repeat

On/Off

Start Time

(Hours)

Auto-repeat on indicator

On/Off status

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	EFA119BK-1A
Armbånd, materiale:	Rustfrit stål
Vandfast:	Ja
Kalender:	Ja
Termometer:	Ja
Urtype:	Armbåndsur
Batterilevetid:	2 År
LED-baggrundsbelysning:	Ja
Batteritype:	SR927W
Antal understøttede batterier:	2
Alarmfunktion:	Ja
Produktdesign:	Luksus
Se opkaldstype:	Analogopkald
Vandbestandig dybde:	100 m
Husets farve:	Rustfrit stål
Båndets hovedfarve:	Rustfrit stål
Etui form:	Rund
Hovedfarve på urskive:	Sort
Køn:	Hanstik
Nøjagtighed:	30 sek/md
Se markørstil:	Ingen nummer-visning
Verdenstid funktkon:	Ja