Casio G-Shock G5600 Manual

Casio Ur G-Shock G5600

Læs gratis den danske manual til Casio G-Shock G5600 (4 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Casio G-Shock G5600, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Operation Guide 3160

MO0905- AE

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a built-in battery. Leaving or using the watch

where it is not exposed to light causes the battery to run

down. Make sure the watch is exposed to light as much as

possible.

•When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

•You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is only partially covered.

Bright Light

Solar cell

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

•The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch

settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

•The actual level at which some functions are disabled depends on the watch model.

•Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a

single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window

Approximately about 8 hours exposure to indoor fluorescent lighting

•Be sure to read “Power Supply” for important information you need to know

when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

•See “Power Saving Function” for more information.

About This Manual

•Depending on the model of your watch, display text appears either as dark figures

on a light background or light figures on a dark background. All sample displays in

this manual are shown using dark figures on a light background.

•Button operations are indicated using the letters shown in the illustration.

•Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate

the display.

Timekeeping Mode Press C.

Countdown Timer Mode Stopwatch Mode

Alarm Mode

▲

World Time Mode

▲

Timekeeping

Use the Timekeeping Mode to set and view the current

time and date.

Read This Before You Set the Time and Date!

This watch is preset with a number of city codes, each of

which represents the time zone where that city is located.

When setting the time, it is important that you first select

the correct city code for your Home City (the city where

you normally use the watch). If your location is not

included in the preset city codes, select the preset city

code that is in the same time zone as your location.

•Note that all of the times for the World Time Mode city

codes are displayed in accordance with the time and

date settings you configure in the Timekeeping Mode.

Current Time

PM indicator

Hour : Minutes

Seconds

Day of week

Month – Day

To set the time and date manually

1. In the Timekeeping Mode hold down A until the city

code starts to flash, which indicates the setting screen.

2. Use D and B to select the city code you want.

•Make sure you select your Home City code before

changing any other setting.

•For full information on city codes, see the “City Code

Table”.

3. Press C to move the flashing in the sequence shown below to select the other

setting.

Seconds

12/24-Hour

Format Hour

Minutes

DST

Month Ye a r

City Code

DayPower Saving

•The following steps explain how to configure timekeeping settings only.

4. When the timekeeping setting you want to change is flashing, use D or B to

change it as described below.

Change the city code

Toggle between Daylight Saving Time (ON)

and Standard Time (OFF).

Toggle between 12-hour ( ) and 24-

hour ( ) timekeeping

Reset the seconds to

Change the hour and minutes

Use D (east) and B

(west).

Press D.

Use D (+) and B (–).

Screen: To do this: Do this:

Change the year, month, or day

Toggle between Power Saving on ( ) and

off ( )

Use D (+) and B (–).

Press D.

5. Press A to exit the setting screen.

•The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

12-hour and 24-hour timekeeping

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C and the DST setting screen appears.

3. Use D to toggle between Daylight Saving Time (DST

indicator displayed) and Standard Time ( indicatorDST

not displayed).

4. When the setting you want is selected, press A to exit

the setting screen.

• The DST indicator appears to indicate that Daylight

Saving Time is turned on.

DST indicator

World Time

World Time shows the current time in 48 cities (29 time

zones) around the world.

•The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

•Select a city code in the World Time Mode to display the

current time in any particular time zone around the

globe. See the “City Code Table” for information about

the UTC differential settings that are supported.

•All of the operations in this section are performed in the

World Time Mode, which you enter by pressing C.

Current time in

selected city

City code

Operation Guide 3160

To view the time in another city

While in the World Time Mode, use the D to scroll through the city codes (time zones).

•Pressing the D B and at the same time will jump to the UTC time zone.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D to display the city code

(time zone) whose Standard Time/Daylight Saving Time

setting you want to change.

2. Hold down A to toggle between Daylight Saving Time

(DST indicator displayed) and Standard Time (DST

indicator not displayed).

•The DST indicator is shown on the World Time Mode

screen while Daylight Saving Time is turned on.

•Note that the Standard Time/Daylight Saving Time

setting affects only the currently displayed city code.

Other city codes are not affected.

•Note that you cannot switch between Standard Time

and Daylight Saving Time while UTC is selected as the

city code.

DST indicator

Alarms

The Alarm Mode gives you a choice of four one-time

alarms and one snooze alarm.

Also use the Alarm Mode to turn the Hourly Time Signal

(SIG) on and off.

•There are five alarm screens numbered AL1 AL2, ,

AL3 AL and 4 for the one-time alarm, a snooze alarm

screen indicated by SNZ. The Hourly Time Signal

screen is indicated by SIG.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

Alarm time

(Hour : Minutes)

Alarm number

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

•To set a one-time alarm, display an alarm screen AL1, , .AL2 AL3 and AL4

To set the snooze alarm, display the SNZ screen.

•The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

•This operation turns on the alarm automatically.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D B (+) and (–) to change it.

•With the 12-hour format, set the time correctly as a.m. or p.m. ( indicator).P

5. Press A to exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off.

•Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

•Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the

SNZ

setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press to toggle it on and off.A

•Turning on a alarm (AL1 AL2 AL3 AL, , , 4 or

SNZ) displays the alarm on indicator ( ) on its Alarm

Mode screen.

•In all modes, the alarm on indicator is shown for any

alarm that is currently turned on.

•The alarm on indicator flashes while the alarm is

sounding.

•The snooze alarm indicator ( ) flashes while the

snooze alarm is sounding and during the 5-minute

intervals between alarms.

Alarm on

indicator

Snooze

alarm

indicator

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use to select the Hourly TimeD

Signal (SIG).

2. Press to toggle it on and off.A

•The Hourly Time Signal on indicator ( ) is shown on

the display in all modes while this function is turned on.

Hourly time signal

on indicator

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

•The display range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

Hours

Minutes

Seconds

1/100 second

To measure times with the stopwatch

Elapsed Time

Split Time

Two Finishes

Start

Stop Re-start Stop

D D

Split

( displayed)

Split release Stop

Split

First runner finishes.

Display time of first

runner.

Stop

Second runner

finishes.

Split release

Display time of

second runner.

D AA

➤➤➤

➤

Clear

Countdown Timer

You can set the countdown timer within a range of one

minute to 24 hours. An alarm sounds when the countdown

reaches zero.

•All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Configuring the Countdown Timer

The following are the settings you should configure before

actually using the countdown timer.

Countdown start time

•See “To configure the countdown timer” for information

about setting up the timer.

Hours

Minutes

Seconds

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero. The

beeper stops after about 10 seconds or when you press any button.

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

•If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” to

display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Hours Minutes

3. When the setting you want to change is flashing, use and D B to change it as

described below.

Button Operation

Use D (+) and B (–) to change the setting.

Setting

Hours, Minutes

Screen

Current timer

time

Timer start time

•To specify a countdown start time of 24 hours, set .

4. Press A to exit the setting screen.

To use the countdown timer

Press D while in the Countdown Timer Mode to start the

countdown timer.

•The countdown timer operation continues even if you

exit the Countdown Timer Mode.

•Press D while a countdown operation is in progress to

pause it. Press again to resume the countdown.D

•To stop a countdown operation completely, first pause it

(by pressing ), and then press . This returns theD A

countdown time to its starting value.

Illumination

This watch has an EL (electro-luminescent) panel that

causes the entire display to glow for easy reading in the

dark. The watch’s auto light switch turns on illumination

automatically when you angle the watch towards your

face.

•The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

•See “Illumination Precautions” for other important

information about using illumination.

To illuminate the display manually

In any mode, press to turn on illumination.B

•The above operation turns on illumination regardless of

the current auto light switch setting.

Auto light switch

on indicator

About the Auto Light Switch

Turning on the auto light switch causes illumination to turn on, whenever you position

your wrist as described below in any mode.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you more than 40 degrees causes illumination to turn on.

• Wear the watch on the outside of your wrist.

Parallel to

ground

More than

40°

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	G-Shock G5600

Har du brug for hjælp?

Hvis du har brug for hjælp til Casio G-Shock G5600 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ur Casio Manualer

Casio AE2000W-1AV Manual

5 September 2025

Casio AEQ-110 Manual

4 September 2025

Casio G-Shock GA-700UC-3A Manual

28 Juli 2025

Casio Baby-G BSA-B100 Manual

27 Juli 2025

Casio G-Shock GM-110 Manual

27 Juli 2025

Casio G-Shock GM-S5600 Manual

27 Juli 2025

Casio Edifice EF-527D-1A Manual

27 Juli 2025

Casio Edifice EFR-571 Manual

27 Juli 2025

Casio G-Shock GST-S110 Manual

27 Juli 2025

Casio Baby-G BGD-570 Manual

27 Juli 2025

Ur Manualer

Nyeste Ur Manualer

Grand Seiko 9F85 Manual

12 September 2025

Grand Seiko 9R01 Manual

11 September 2025

Grand Seiko 9R65 Manual

11 September 2025

Grand Seiko 9R02 Manual

11 September 2025

Grand Seiko 9R15 Manual

11 September 2025

Citizen Attesa Satellite Wave GPS Layers of Time CC4057-60E Manual

3 September 2025

Citizen L Mae EM1060-52N Manual

3 September 2025

Citizen Corso Diamond EW2712-55E Manual

3 September 2025

Citizen Attesa Radio Controlled Layers of Time AT8286-65E Manual

3 September 2025

Breitling AVI Ref. 765 1964 Re-Edition Manual

28 August 2025