Casio G-Shock GM-S2140 Manual

Casio Ur G-Shock GM-S2140

Læs gratis den danske manual til Casio G-Shock GM-S2140 (6 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 70 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 35.5 anmeldelser. Har du et spørgsmål om Casio G-Shock GM-S2140, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
Operation Guide 5229 5518
E-9
To set the digital time and date
1. In the Timekeeping Mode, hold down
A
for about three
seconds until the currently selected city code flashes in
the right digital dial. This is the setting mode.
D
(east) and
B
(west) to display the city code
you want to select.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table” at the back of this manual.
City code
PM indicator
Hour : Minutes
Seconds
E-8
Timekeeping
You can adjust the Home Time city date and time in the Timekeeping Mode.
• The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
• If the analog time does not match the digital time for any reason, use the procedure
described under “To adjust home positions” (page E-44) to match the analog setting to
the digital setting.
• Pressing
D
in the Timekeeping Mode toggles digital display between the Home
City Date and Home City Time.
Home City Date Home City Time
Day of weekMonth Day
PM indicator
Hour : MinutesDay of week
Seconds
Seconds
D
E-7
Alarm Mode
(page E-34)
Countdown Timer Mode
(page E-26)
World Time Mode
(page E-30)
Stopwatch Mode
(page E-14)
C
C
C
E-6
General Guide
• Press
C
to change from mode to mode.
• In any mode (except a setting mode), press
B
to illuminate the face.
Timekeeping Mode
C
C
E-5
Illumination ……………………………………………………………………………E-39
To illuminate the face manually ………………………………………………E-39
To specify the illumination duration……………………………………………E-40
To turn the auto light switch on and off ………………………………………E-43
Hand Home Position Correction ……………………………………………………E-44
To adjust home positions ………………………………………………………E-44
Reference ………………………………………………………………………………E-46
Specifications …………………………………………………………………………E-50
E-4
Countdown Timer………………………………………………………………………E-26
To use the countdown timer ……………………………………………………E-27
To configure countdown start time and auto-repeat settings ………………E-28
World Time ………………………………………………………………………………E-30
To view the current time in another time zone ………………………………E-31
To toggle a city code time between Standard Time and
Daylight Saving Time ………………………………………………………E-32
To swap your Home City and World Time City ………………………………E-33
Alarms ……………………………………………………………………………………E-34
To set an alarm time ……………………………………………………………E-35
To turn an alarm on and off ……………………………………………………E-37
To turn the Hourly Time Signal on and off ……………………………………E-38
E-3
Contents
General Guide ………………………………………………………………………… E-6
Timekeeping …………………………………………………………………………… E-8
To set the digital time and date ……………………………………………… E-9
To change the Daylight Saving Time (summer time) setting ………………E-12
Stopwatch ………………………………………………………………………………E-14
To specify a distance value ……………………………………………………E-16
To specify lap time or split time readings ……………………………………E-19
To perform elapsed time measurement ………………………………………E-20
To set up the stopwatch to take lap time readings …………………………E-21
To perform a lap time measurement …………………………………………E-22
To set up the stopwatch to take split time readings …………………………E-23
To perform a split time measurement …………………………………………E-24
To measure times with the stopwatch ………………………………………E-25
E-2
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
E-1
About This Manual
• Depending on the model of your watch, digital display
text appears either as dark figures on a light
background or light figures on a dark background. All
sample displays in this manual are shown using dark
figures on a light background.
• Button operations are indicated using the letters shown
in the illustration.
• Note that the product illustrations in this manual are
intended for reference only, and so the actual product
may appear somewhat different than depicted by an
illustration.
MO1610-EA
© 2016 CASIO COMPUTER CO., LTD.
Operation Guide 5229 5518
E-19
To specify lap time or split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• Make sure that (lap times) or (split times) is shown in the left digital LAP SPL
dial.
• If you need to reset the stopwatch to all zeros, press
A
.
2. You can toggle between (lap times) and (split times) by pressing LAP SPL
A
.
A
E-18
Example:
When the speed value is 1,740.
Speed hand: Indicates
40
.
Right dial display segments: Indicate
700
.
1000
indicator: Displayed
Time Measurement
You need to specify either lap time (page E-21) or split time (page E-23) measurement before
you start a stopwatch operation.
• If you want to measure total elapsed time, select split time measurement.
E-17
How speed is indicated
• While an elapsed time measurement operation is being
performed in the Stopwatch Mode, the watch will
indicate a speed value, which is calculated based on
the distance you specified and the elapsed time.
The speed value is indicated as described below.
Speed hand: Up to 100
Right dial display segments: 100 unit
A
1000
indicator points to 1000 (located to the right of
the right dial display segments) when the speed value
is between 1000 and 1998.
• The speed hand indicates speed values less than 100.
Only even-numbered values are indicated.
• Speed can be indicated from 0 to 1998.
OVER
is
indicated by the speed hand when the speed exceeds
1998.
Segments
(100 unit)
OVER
Speed hand
(Up to 100)
1000 indicator
E-16
To specify a distance value
1. In the Stopwatch Mode, make sure the stopwatch is
stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press
A
.
2. Hold down
A
for about three seconds until the current
distance value setting flashes in the left digital dial.
• This is the distance value setting mode.
3. Press
C
to move the flashing between the values on
the left side and right side of the distance value decimal
point.
4. While a distance value is flashing, use
D
(+) and
B
(–)
to change it.
• You can specify a distance value in the range of 0.1
to 99.9.
5. After specifying the distance value you want, press
A
to exit the setting mode.
E-15
Important!
• Check to make sure that the speed hand is not moving before you perform any
Stopwatch Mode button operation.
Specifying a Distance Value
You can use the procedure below to specify a distance value, if you want. If you
specify a distance value, the watch will calculate and indicate speed for certain
stopwatch operations.
• The distance value represents kilometers, miles, or any other distance unit you
want. Specifying a distance value of 10.0, for example, can mean 10.0 kilometers or
10.0 miles.
• No speed calculation is performed when 0.0 is specified as the current distance
value.
• For lap time readings, you can specify either the lap distance (when all the laps are
the same distance) or the total race distance.
• For split time readings, you can specify the total race distance only. Though the
watch will indicate a speed each time you take a split reading, they will be based
on the total race distance, and so they will not indicate actual intermediate split
speeds.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time, lap
times and split times. If you specify a distance value, the
stopwatch also will calculate and display speeds.
• The digital display range of the stopwatch is 99 hours,
59 minutes, 59.999 seconds. The stopwatch continues
to run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode. If you exit the Stopwatch Mode while
a stopwatch operation is in progress, the segments
along the top of the right digital dial (right dial display
segments) will indicate the seconds of the current time.
Each segment represents one second. This is to let you
know that a stopwatch operation is in progress.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
(page E-7).
Speed hand Right dial
display
segments
E-13
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator appears in the left digital dial for times in
the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-12
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
A
for about three
seconds until the currently selected city code flashes in
the right digital dial. This is the setting mode.
2. Press
C
. This will display the DST setting screen.
D
to toggle the DST setting on (
on
) and off (
OFF
).
• The default DST setting is off (
OFF
).
4. When the setting you want is selected, press
A
to exit
the setting mode.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
DST indicator
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
12H
) and
24-hour (
24H
) timekeeping
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour and minutes
Use
D
(+) and
B
(–).
Change the year, month, or day
Toggle the face illumination duration
between 1.5 seconds (
LT1
) and three
seconds (
LT3
)
Press
D
.
5. Press
A
to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date
(year, month, and day) settings.
E-10
3. Press
C
to change the flashing screen content in the sequence shown below to
select the other settings.
City Code DST
12/24-Hour
Format
Illumination
Duration
Seconds Hour
YearMonthDay Minutes
4. When the setting you want to change is flashing, use
D
or
B
to change it as
described below.
Screen: To do this: Do this:
Change the city code
Use
D
(east) and
B
(west).
Toggle the DST setting between Daylight
Saving Time (
on
) and Standard Time
(
OFF
).
Press
D
.

Produkt Specifikationer

Mærke: Casio
Kategori: Ur
Model: G-Shock GM-S2140

Har du brug for hjælp?

Hvis du har brug for hjælp til Casio G-Shock GM-S2140 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ur Casio Manualer

Casio

Casio AE2000W-1AV Manual

5 September 2025
Casio

Casio AEQ-110 Manual

4 September 2025
Casio

Casio G-Shock GA-700UC-3A Manual

28 Juli 2025
Casio

Casio Baby-G BSA-B100 Manual

27 Juli 2025
Casio

Casio G-Shock GM-110 Manual

27 Juli 2025
Casio

Casio G-Shock GM-S5600 Manual

27 Juli 2025
Casio

Casio Edifice EF-527D-1A Manual

27 Juli 2025
Casio

Casio Edifice EFR-571 Manual

27 Juli 2025
Casio

Casio G-Shock GST-S110 Manual

27 Juli 2025
Casio

Casio Baby-G BGD-570 Manual

27 Juli 2025

Ur Manualer

Nyeste Ur Manualer

Grand Seiko

Grand Seiko 9F85 Manual

12 September 2025
Grand Seiko

Grand Seiko 9R01 Manual

11 September 2025
Grand Seiko

Grand Seiko 9R65 Manual

11 September 2025
Grand Seiko

Grand Seiko 9R02 Manual

11 September 2025
Grand Seiko

Grand Seiko 9R15 Manual

11 September 2025
Citizen

Citizen Attesa Satellite Wave GPS Layers of Time CC4057-60E Manual

3 September 2025
Citizen

Citizen L Mae EM1060-52N Manual

3 September 2025
Citizen

Citizen Corso Diamond EW2712-55E Manual

3 September 2025
Citizen

Citizen Attesa Radio Controlled Layers of Time AT8286-65E Manual

3 September 2025
Breitling

Breitling AVI Ref. 765 1964 Re-Edition Manual

28 August 2025