Casio G-SHOCK GMAS120MF-2A2 Manual

Casio Ur G-SHOCK GMAS120MF-2A2

Læs gratis den danske manual til Casio G-SHOCK GMAS120MF-2A2 (6 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Casio G-SHOCK GMAS120MF-2A2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Operation Guide 5229 5518

E-9

To set the digital time and date

1. In the Timekeeping Mode, hold down A for about three

seconds until the currently selected city code flashes in

the right digital dial. This is the setting mode.

2. Use D (east) and B (west) to display the city code

you want to select.

• Make sure you select your Home City code before

changing any other setting.

• For full information on city codes, see the “City Code

Table” at the back of this manual.

City code

PM indicator

Hour : Minutes

Seconds

E-8

Timekeeping

You can adjust the Home Time city date and time in the Timekeeping Mode.

• The analog time of this watch is synchronized with the digital time. The analog time

setting is adjusted automatically whenever you change the digital time.

• If the analog time does not match the digital time for any reason, use the procedure

described under “To adjust home positions” (page E-44) to match the analog setting to

the digital setting.

• Pressing D in the Timekeeping Mode toggles digital display between the Home

City Date and Home City Time.

Home City Date Home City Time

Day of weekMonth Day PM indicator Hour : MinutesDay of week

SecondsSeconds

E-7

Alarm Mode (page E-34)

Countdown Timer Mode (page E-26)

World Time Mode (page E-30)

Stopwatch Mode (page E-14)

E-6

General Guide

• Press C to change from mode to mode.

• In any mode (except a setting mode), press B to illuminate the face.

Timekeeping Mode

E-5

Illumination ……………………………………………………………………………E-39

To illuminate the face manually ………………………………………………E-39

To specify the illumination duration……………………………………………E-40

To turn the auto light switch on and off ………………………………………E-43

Hand Home Position Correction ……………………………………………………E-44

To adjust home positions ………………………………………………………E-44

Reference ………………………………………………………………………………E-46

Specifications …………………………………………………………………………E-50

E-4

Countdown Timer………………………………………………………………………E-26

To use the countdown timer ……………………………………………………E-27

To configure countdown start time and auto-repeat settings ………………E-28

World Time ………………………………………………………………………………E-30

To view the current time in another time zone ………………………………E-31

To toggle a city code time between Standard Time and

Daylight Saving Time ………………………………………………………E-32

To swap your Home City and World Time City ………………………………E-33

Alarms ……………………………………………………………………………………E-34

To set an alarm time ……………………………………………………………E-35

To turn an alarm on and off ……………………………………………………E-37

To turn the Hourly Time Signal on and off ……………………………………E-38

E-3

Contents

General Guide ………………………………………………………………………… E-6

Timekeeping …………………………………………………………………………… E-8

To set the digital time and date ……………………………………………… E-9

To change the Daylight Saving Time (summer time) setting ………………E-12

Stopwatch ………………………………………………………………………………E-14

To specify a distance value ……………………………………………………E-16

To specify lap time or split time readings ……………………………………E-19

To perform elapsed time measurement ………………………………………E-20

To set up the stopwatch to take lap time readings …………………………E-21

To perform a lap time measurement …………………………………………E-22

To set up the stopwatch to take split time readings …………………………E-23

To perform a split time measurement …………………………………………E-24

To measure times with the stopwatch ………………………………………E-25

E-2

• Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

E-1

About This Manual

• Depending on the model of your watch, digital display

text appears either as dark figures on a light

background or light figures on a dark background. All

sample displays in this manual are shown using dark

figures on a light background.

• Button operations are indicated using the letters shown

in the illustration.

• Note that the product illustrations in this manual are

intended for reference only, and so the actual product

may appear somewhat different than depicted by an

illustration.

Operation Guide 5229 5518

E-19

To specify lap time or split time readings

1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.

• Make sure that (lap times) or (split times) is shown in the left digital LAP SPL

dial.

• If you need to reset the stopwatch to all zeros, press A.

2. You can toggle between (lap times) and (split times) by pressing LAP SPL A.

E-18

Example:

When the speed value is 1,740.

Speed hand: Indicates 40.

Right dial display segments: Indicate 700.

1000 indicator: Displayed

Time Measurement

You need to specify either lap time (page E-21) or split time (page E-23) measurement before

you start a stopwatch operation.

• If you want to measure total elapsed time, select split time measurement.

E-17

How speed is indicated

• While an elapsed time measurement operation is being

performed in the Stopwatch Mode, the watch will

indicate a speed value, which is calculated based on

the distance you specified and the elapsed time.

The speed value is indicated as described below.

Speed hand: Up to 100

Right dial display segments: 100 unit

A 1000 indicator points to 1000 (located to the right of

the right dial display segments) when the speed value

is between 1000 and 1998.

• The speed hand indicates speed values less than 100.

Only even-numbered values are indicated.

• Speed can be indicated from 0 to 1998.

OVER is

indicated by the speed hand when the speed exceeds

1998.

Segments

(100 unit)

OVER

Speed hand

(Up to 100)

1000 indicator

E-16

To specify a distance value

1. In the Stopwatch Mode, make sure the stopwatch is

stopped and reset to all zeros.

• If you need to reset the stopwatch to all zeros, press

2. Hold down A for about three seconds until the current

distance value setting flashes in the left digital dial.

• This is the distance value setting mode.

3. Press C to move the flashing between the values on

the left side and right side of the distance value decimal

point.

4. While a distance value is flashing, use D (+) and B (–)

to change it.

• You can specify a distance value in the range of 0.1

to 99.9.

5. After specifying the distance value you want, press A

to exit the setting mode.

E-15

Important!

• Check to make sure that the speed hand is not moving before you perform any

Stopwatch Mode button operation.

Specifying a Distance Value

You can use the procedure below to specify a distance value, if you want. If you

specify a distance value, the watch will calculate and indicate speed for certain

stopwatch operations.

• The distance value represents kilometers, miles, or any other distance unit you

want. Specifying a distance value of 10.0, for example, can mean 10.0 kilometers or

10.0 miles.

• No speed calculation is performed when 0.0 is specified as the current distance

value.

• For lap time readings, you can specify either the lap distance (when all the laps are

the same distance) or the total race distance.

• For split time readings, you can specify the total race distance only. Though the

watch will indicate a speed each time you take a split reading, they will be based

on the total race distance, and so they will not indicate actual intermediate split

speeds.

E-14

Stopwatch

You can use the stopwatch to measure elapsed time, lap

times and split times. If you specify a distance value, the

stopwatch also will calculate and display speeds.

• The digital display range of the stopwatch is 99 hours,

59 minutes, 59.999 seconds. The stopwatch continues

to run until you stop it. If it reaches the above limit, it will

restart the time measurement from zero.

• The stopwatch operation continues even if you exit the

Stopwatch Mode. If you exit the Stopwatch Mode while

a stopwatch operation is in progress, the segments

along the top of the right digital dial (right dial display

segments) will indicate the seconds of the current time.

Each segment represents one second. This is to let you

know that a stopwatch operation is in progress.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing

(page E-7).

Speed hand Right dial

display

segments

E-13

12-hour and 24-hour timekeeping

• With the 12-hour format, the PM indicator appears in the left digital dial for times in

the range of noon to 11:59 p.m. and no indicator appears for times in the range of

midnight to 11:59 a.m.

• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

the PM indicator.

• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

E-12

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A for about three

seconds until the currently selected city code flashes in

the right digital dial. This is the setting mode.

2. Press C. This will display the DST setting screen.

3. Use D to toggle the DST setting on (on) and off (

OFF).

• The default DST setting is off (OFF).

4. When the setting you want is selected, press A to exit

the setting mode.

• The DST indicator appears to indicate that Daylight

Saving Time is turned on.

DST indicator

E-11

Screen: To do this: Do this:

Toggle between 12-hour (

12H) and

24-hour (24H

) timekeeping Press D.

Reset the seconds to

00 Press D.

Change the hour and minutes

Use D (+) and B (–).

Change the year, month, or day

Toggle the face illumination duration

between 1.5 seconds (

LT1) and three

seconds (LT3

)

Press D.

5. Press A to exit the setting mode.

• The day of the week is displayed automatically in accordance with the date

(year, month, and day) settings.

E-10

3. Press C to change the flashing screen content in the sequence shown below to

select the other settings.

City Code DST 12/24-Hour

Format

Illumination

Duration

Seconds Hour

YearMonthDay Minutes

4. When the setting you want to change is flashing, use D or B to change it as

described below.

Screen: To do this: Do this:

Change the city code Use D (east) and B

(west).

Toggle the DST setting between Daylight

Saving Time (on) and Standard Time

(OFF).

Press D.

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	G-SHOCK GMAS120MF-2A2
Bluetooth:	Ingen
Armbånd, materiale:	Resin
Vandfast:	Ja
Urkassens materiale:	Resin
Kalender:	Ja
Ur-indstilling:	12t/24t
Stopur:	Ja
Urtype:	Armbåndsur
Batterilevetid:	3 År
LED-baggrundsbelysning:	Ja
Batteritype:	CR 1220
Antal understøttede batterier:	1
Slagfast:	Ja
Urets glastype:	Mineral
Alarmfunktion:	Ja
Produktdesign:	Sport
Mekanismetype:	Elektronisk
Se opkaldstype:	Analog & LCD-opkald
Vandbestandig dybde:	200 m
Husets farve:	Blå
Båndets hovedfarve:	Gold, Pink
Etui form:	Rund
Hovedfarve på urskive:	Guld/Pink
Køn:	Hunstik
Regnemaskine:	Ingen
Nøjagtighed:	± 15 sek/md
Tidzoner:	Ja
Nedtællingsur:	Ja
Verdenstid funktkon:	Ja
Anti-magnetisk:	Ja
Stopur målingskapacitet:	99: 59'59.999
Nedtællingstimer område:	1440 - 1440 min.