Casio GW-9200-1ER Manual

Casio Ur GW-9200-1ER

Læs nedenfor 📖 manual på dansk for Casio GW-9200-1ER (12 sider) i kategorien Ur. Denne guide var nyttig for 5 personer og blev bedømt med 4.6 stjerner i gennemsnit af 3 brugere

Download PDF

Side 1/12

Operation Guide 3147

MO1010-EC

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out

of your purchase, be sure to read this manual carefully.

Applications

The built-in sensors of this watch measure barometric pressure, temperature

and altitude. Measured values are then shown on the display. Such features

make this watch useful when hiking, mountain climbing, or when engaging in

other such outdoor activities.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the

watch is stored by a built-in battery. Leaving or

using the watch where it is not exposed to light

causes the battery to run down. Make sure the

watch is exposed to light as much as possible.

•When you are not wearing the watch on your

wrist, position the face so it is pointed at a

source of bright light.

•You should try to keep the watch outside of

your sleeve as much as possible. Charging is

reduced significantly if the face is covered only

partially.

Bright light

Solar cell

•The watch continues to operate, even when it is not exposed to light.

Leaving the watch in the dark can cause the battery to run down, which will

cause some watch functions to be disabled. If the battery goes dead, you

will have to re-configure watch settings after recharging. To ensure normal

watch operation, be sure to keep it exposed to light as much as possible.

Bright light

Electrical

energy

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Solar cell

(Converts light to

electrical power.)

Rechargeable battery

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

•The actual level at which some functions are disabled depends on the

watch model.

•Frequent display illumination can run down the battery quickly and require

charging. The following guidelines give an idea of the charging time

required to recover from a single illumination operation.

Approximately five minutes exposure to bright sunlight coming in through

a window

Approximately 50 minutes exposure to indoor fluorescent lighting

•Be sure to read “Power Supply” for important information you need to

know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving

function has turned off the display to conserve power.

•See “Power Saving” for more information.

Warning!

•The measurement functions built into this watch are not intended for

taking measurements that require professional or industrial precision.

Values produced by this watch should be considered as reasonable

representations only.

•CASIO COMPUTER CO., LTD. assumes no responsibility for any loss,

or any claims by third parties that may arise through the use of this

watch.

About This Manual

•Button operations are indicated using the letters shown in the illustration.

•Each section of this manual provides you with the information you need to

perform operations in each mode. Further details and technical information

can be found in the “Reference” section.

(Light)(Light)

General Guide

•The illustration below shows which buttons you need to press to navigate

between modes.

•In any mode, press L to illuminate the display.

•You can press the button to go directly from the Timekeeping Mode toC

the Altimeter Mode. To go to the Altimeter Mode from the Barometer/

Thermometer, World Time, Stopwatch, Countdown Timer, Alarm, or Data

Recall Mode, first enter the Timekeeping Mode and then press the C

button. Timekeeping Mode

Altimeter Mode

World Time Mode

Data Recall Mode

Countdown

Timer Mode

Press D.

Stopwatch Mode

Barometer/

Thermometer Mode

Alarm Mode

▲

Press D.

▲

Press .C

▲

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting

accordingly.

•This watch is designed to pick up the time calibration signals transmitted in

Germany (Mainflingen), England (Anthorn), the United States (Fort Collins),

China (Shangqiu), and Japan (Fukushima, Fukuoka/Saga).

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time

calibration signal. You also can perform a manual procedure to set the time

and date, when necessary.

•The first thing you should do after purchasing this watch is to specify

your Home City (the city where you normally will use the watch). For

more information, see “To specify your Home City” below.

•When using the watch outside the areas covered by the time signal

transmitters, you will have to adjust the current time setting manually as

required. See

“Timekeeping” for more information about manual time

settings.

•The U.S. time calibration signal can be picked up by the watch while in

North America. The term “North America” in this manual refers to the area

that consists of Canada, the continental United States, and Mexico.

To specify your Home City

1. In the Timekeeping Mode, hold down untilA

the city code starts to flash, which indicates

the setting screen.

2. Press E (east) and B (west) to select the

city code you want to use as your Home City.

LON : London

PAR, BER : Paris, Berlin, Milan, Rome,

Amsterdam, Hamburg, Frankfurt,

Vienna, Barcelona, Madrid

ATH : Athens

HKG : Hong Kong

TPE TYO, : Taipei, Tokyo

LAX :Los Angeles, San Francisco, Las Vegas, Seattle/Tacoma,

Vancouver, Tijuana

City code

Hour : Minutes

indicator

Seconds

DEN :Denver, El Paso, Edmonton, Culiacan

CHI :Chicago, Houston, Dallas/Fort Worth, New Orleans, Winnipeg,

Mexico City

NYC :New York, Detroit, Miami, Boston, Montreal

Operation Guide 3147

3. Press A to exit the setting screen.

•Normally, your watch should show the correct time as soon as you select

your Home City code. If it does not, it should adjust automatically after the

next auto receive operation (in the middle of the night). You also can

perform manual receive or you can set the time manually.

•The watch will receive the time calibration signal automatically from the

applicable transmitter (in the middle of the night) and update its settings

accordingly. For information about the relationship between city codes and

transmitters, see “ ”Important! under “ ”Time Calibration Signal Reception

and Transmitters“ ”.

•See the maps under “Approximate Reception Ranges for information about”

the reception ranges of the watch.

•You can disable time signal reception, if you want. See “To turn auto receive

on and off for more information.”

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration

signal: auto receive and manual receive.

•Auto Receive

With auto receive, the watch receives the time calibration signal automatically

up to six times a day. When any auto receive is successful, the remaining

auto receive operations are not performed. For more information, see “About

Auto Receive”.

•Manual Receive

Manual receive lets you start a time calibration receive operation with the press

of a button. For more information, see To perform manual receive“ ”.

Important!

•When getting ready to receive the time calibration signal, position the watch

as shown in the nearby illustration, with its 12 o clock side facing towards a’

window. This watch is designed to receive a time calibration signal late at

night. Because of this, you should place the watch near a window as shown

in the illustration when you take it off at night. Make sure there are no metal

objects nearby.

12 o’clock

•Make sure the watch is facing the right way.

•Proper signal reception can be difficult or even impossible under the

conditions listed below.

•Signal reception normally is better at night than during the day.

•Time calibration signal reception takes from two to seven minutes, but in

some cases it can take as long as 14 minutes. Take care that you do not

perform any button operations or move the watch during this time.

Inside or

among

buildings

Inside a

vehicle

Near a

construction

site, airport,

or other

sources of

electrical

noise

Near high-

tension

power lines

Among or

behind

mountains

Near

household

appliances,

office

equipment,

or a mobile

phone

•The time calibration signal the watch will attempt to pick up depends on its

current Home City code setting as shown below.

Home City Code

LON BER, PAR, , ATH

HKG

TPE, TYO

HNL*, ANC*, LAX,

DEN, CHI, NYC

Frequency

60.0 kHz

77.5 kHz

68.5 kHz

40.0 kHz

60.0 kHz

Transmitter

Anthorn (England)

Mainflingen (Germany)

Shangqiu City (China)

Fukushima (Japan)

Fukuoka/Saga (Japan)

Fort Collins, Colorado

(the United States)

* The areas covered by the , and city codes are quite far fromHNL ANC

the time calibration signal transmitters, and so certain conditions may

cause problems with signal reception.

Approximate Reception Ranges

Anthorn

Mainflingen

1,500 kilometers

500 kilometers

Fort

Collins

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

The Anthorn

signal is

receivable within

this area.

1,000

kilometers

1,000

kilometers

Fukuoka/Saga

500

kilometers

Fukushima

500

kilometers

500 kilometers

Changchun

Beijing

1,500 kilometers

Shangqiu

Shanghai

Hong Kong

Chengdu

Signals are receivable in the Taiwan area when reception conditions are good.

•Signal reception may not be possible at the distances noted below during

certain times of the year or day. Radio interference may also cause

problems with reception.

Mainflingen (Germany) or Anthorn (England) transmitters: 500

kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310

miles)

Shangqiu (China) transmitter: 1500 kilometers (910 miles)

•Even when the watch is within the reception range of the transmitter, signal

reception will be impossible if the signal is blocked by mountains or other

geological formations between the watch and signal source.

•Signal reception is affected by weather, atmospheric conditions, and

seasonal changes.

•See the information under Signal Reception Troubleshooting“ ” if you

experience problems with time calibration signal reception.

About Auto Receive

The watch receives the time calibration signal automatically up to six times a

day. When any auto receive is successful, the remaining auto receive

operations are not performed. The reception schedule (calibration times)

depends on your currently selected Home City, and whether standard time or

Daylight Saving Time is selected for your Home City.

Your Home City Auto Receive Start Times

1 2 3 4 5 6

LON Standard Time

1:00 am 2:00 am 3:00 am 4:00 am 5:00 am Midnight*

Daylight Saving Time

2:00 am 3:00 am 4:00 am 5:00 am Midnight* 1:00 am

PAR Standard Time

2:00 am 3:00 am 4:00 am 5:00 am Midnight* 1:00 am

BER

Daylight Saving Time

3:00 am 4:00 am 5:00 am Midnight* 1:00 am

2:00 am

ATH Standard Time

3:00 am 4:00 am 5:00 am Midnight* 1:00 am

2:00 am

Daylight Saving Time

4:00 am 5:00 am Midnight* 1:00 am

2:00 am

3:00 am

HKG Standard Time

1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

TYO Standard Time

Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

TPE

NYC Standard Time and

Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am

CHI

Daylight Saving Time

DEN

LAX

*Next day

Produkt Specifikationer

Mærke:	Casio
Kategori:	Ur
Model:	GW-9200-1ER
Vægt:	60.9 g
Dimensioner (BxDxH):	48.9 x 15.9 x 51 mm
Armbånd, materiale:	Resin
Urkassens materiale:	Resin
Kalender:	Ja
Ur-indstilling:	12t/24t
Stopur:	Ja
Barometer:	Ja
Højdemåler:	Ja
Termometer:	Ja
Timer:	1/1min - 24h
Indikator for batteriniveau:	Ja
Batteritype:	CTL1616
Antal understøttede batterier:	1
Slagfast:	Ja
Urets glastype:	Mineral
Alarmfunktion:	Ja
Snooze funktion:	Ja
Vandbestandig dybde:	200 m
Verdenstid funktkon:	Ja
Radiosignal modtager:	DCF/MSF/WWVB/JJY/BPC
Solenergi:	Ja