Cateye Fit CC-PD100W Manual

Cateye Cykelcomputer Fit CC-PD100W

Læs gratis den danske manual til Cateye Fit CC-PD100W (3 sider) i kategorien Cykelcomputer. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Cateye Fit CC-PD100W, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
Measure wheel circumference (L) of your bike
To get the most accurate
calibration do a wheel roll out.
With the valve stem perpen-
dicular to the ground, mark
the pavement at the valve
stem. With the riders weight
on the bike, roll the wheel one tire revolution
in a straight line and mark the ground when
the valve stem is perpendicular to the ground
again. Measure the distance in millimeters. This
is the most accurate wheel calibration number.
Before using the computer, please thoroughly read this manual and keep it for future
reference.
Our website shows how to install and set up the unit on your bicycle, in an understandable way
using a movie .(http://www.cateye.com)
Installation conditions
The back of the com-•
puter must face the
speed sensor.
1
Removing the insulation sheet
Remove the battery case cover, and hold
the battery holder tab to pull out the battery.
The battery holder is lifted when either tab
is pulled up. Remove the insulation sheet
under the battery.
If the battery is detached, insert it cor-*
rectly. ( )Replacing the battery
Insert the battery holder with the * mark
toward the front side of the computer.
2
Press the button while press-AC
ing and holding the button MENU
(formatting operation)
Check that the
whole screen illu-
mination is turned
on for 5 seconds.
Press and hold the * MENU button for 3
seconds after you release the button.AC
3
Select the measurement unit
(Speed, Stride, and Weight)
When the
1.
MODE button is
pressed, “KM. CM. KG”
and “MILE. INCH. LB”
will fl ash alternatively for
selection.
With the desired measurement unit dis-2.
played, press the button.MENU
4
Set the date
When the 1. MODE button
is pressed, “ ” YY/MM/DD
(Year, Month, Day) will
flash in different order
for selection.
When the
2.
MODE button is
pressed and held, the item to set will appear
for selection, and “11” (Year) will fl ash.
Press the 3. MODE button to increase the
fl ashing value, whereas press and hold it
to switch the item to set. Set “Month” and
“Day” in the same procedure.
Press the
4. MENU button to proceed to “Set
the clock”.
When it fails to set the date, “* ERROR” will appear.
5
Set the clock
Set the display format of
“ ” or “ ”, and the 12H 24H
values for “Hour” and
“Minute” in the same
procedure as Step 4.
Press the MENU button
to proceed to “Enter the
tire circumference”.
For the display format of “* 12H”, select
“ ” (morning) or “ ” (afternoon). AM PM
6
Enter the tire circumference
Enter the tire circumference of your
bicycle (distance per turn) in mm.
( Tire circumference reference table)
Press the
1. MODE but-
ton to adjust the value,
and press and hold it to
move to the next digit.
Enter the value for “ones
place digit” through “thousands place digit”
in the same procedure.
Press the
2.
MENU button to proceed to “Enter
the weight”.
When any invalid value is entered, *
“ ” will appear.ERROR
7
Enter the weight
Enter your weight in the
unit you selected in Step
3 ( or ).KG LB
Set the value in the same
procedure as Step 6.
Press the MENU button to proceed to
“Enter the stride”.
8
Enter the stride
Enter your stride in the
unit you selected (CM
or ). (INCH How to
measure the stride)
Set the value in the
same procedure as Step . 6
Press the button to confi rm the setting.MENU
Now, preparing the computer is completed.
AC
MENU
SENSOR ZONE
SENSOR ZONE
SENSOR Z ONE
SENSOR ZONE
5 mm5 mm
Nylon ties (x2)
Sensor zone
Speed sensor
Speed sensor Sensor zone
Magnet
Magnet
Max
70 cm
YES!
Pull
securely
Nylon ties
To the sensor zone
When attaching the bracket to the handlebar
Install the bracket and computer
Package contents
Remove/install the computer
Install the speed sensor Install the magnet
For receiving sensitivity reasons, attach the bracket so that the back of the computer faces the speed sensor.*
Use the applicable optional parts when attaching to an aero-shaped handlebar or a large stem.*
Click
While supporting it by hand,
push it out as if lifting the
front up.
Install it fi rmly in place
until it clicks.
Cut
CAUTION:
Round off the cut edge
of the bracket band to
prevent injury.
ETRTO Tire size
L (mm)
47-203 12x1.75 935
54-203 12x1.95 940
40-254 14x1.50 1020
47-254 14x1.75 1055
40-305 16x1.50 1185
47-305 16x1.75 1195
54-305 16x2.00 1245
28-349 16x1-1/8 1290
37-349 16x1-3/8 1300
32-369 17x1-1/4 (369) 1340
40-355 18x1.50 1340
47-355 18x1.75 1350
32-406 20x1.25 1450
35-406 20x1.35 1460
40-406 20x1.50 1490
47-406 20x1.75 1515
50-406 20x1.95 1565
28-451 20x1-1/8 1545
37-451 20x1-3/8 1615
37-501 22x1-3/8 1770
40-501 22x1-1/2 1785
47-507 24x1.75 1890
50-507 24x2.00 1925
54-507 24x2.125 1965
25-520 24x1(520) 1753
24x3/4 Tubuler 1785
28-540 24x1-1/8 1795
32-540 24x1-1/4 1905
25-559 26x1(559) 1913
32-559 26x1.25 1950
37-559 26x1.40 2005
40-559 26x1.50 2010
47-559 26x1.75 2023
50-559 26x1.95 2050
54-559 26x2.10 2068
Preparing the computer
Element names
How to install the unit on your bicycle
Stem
Bracket
Bracket
Speed sensor
Sensor rubber pad
Bracket rubber pad
Bracket rubber pad
Remove
backing
Remove
backing
Bracket band
Bracket band Handlebar Dial
Right front fork
Spoke
Magnet
SENS
Display format
Clock display
Hour/Minute
YY/MM/DD
u
Bracket band
Bracket
Dial
Speed sensor
Magnet
Bracket rubber pad Sensor rubber pad
AC
MODE
MODE
MENU
Dot section
Battery
case
cover
The clearance between the speed sensor •
and magnet is 5 mm or less.
After installing the speed sensor, check that the speed is displayed on the computer by turn-
ing the front wheel with the computer installed to the bracket. If not displayed, review the
installation conditions, and check the positions of the speed sensor and magnet.
CAUTION:
The computer in the bike mode measures speed only when installed on the bracket.
NO!
This unit can be used for measuring speed and distance while installed on your bicycle, and also used
as a pedometer for measuring calorie consumption and number of steps in everyday life while carried
with you all the time. First of all, go through “Preparing the computer” and “How to install the unit on
your bicycle”.
Tire circumference reference table
Generally, the tire size is indicated on the *
side of the tire.
ETRTO Tire size
L (mm)
57-559 26x2.125 2070
58-559 26x2.35 2083
75-559 26x3.00 2170
28-590 26x1-1/8 1970
37-590 26x1-3/8 2068
37-584 26x1-1/2 2100
650C Tubuler
26x7/8 1920
20-571 650x20C 1938
23-571 650x23C 1944
25-571 650x25C
26x1(571) 1952
40-590 650x38A 2125
40-584 650x38B 2105
25-630 27x1(630) 2145
28-630 27x1-1/8 2155
32-630 27x1-1/4 2161
37-630 27x1-3/8 2169
18-622 700x18C 2070
19-622 700x19C 2080
20-622 700x20C 2086
23-622 700x23C 2096
25-622 700x25C 2105
28-622 700x28C 2136
30-622 700x30C 2146
32-622 700x32C 2155
700C Tubuler 2130
35-622 700x35C 2168
38-622 700x38C 2180
40-622 700x40C 2200
42-622 700x42C 2224
44-622 700x44C 2235
45-622 700x45C 2242
47-622 700x47C 2268
54-622 29x2.1 2288
60-622 29x2.3 2326
When attaching the bracket to the stem
Install the speed sensor and magnet
How to measure the stride
The stride means the distance between
adjacent tiptoes of your footprint. Mark at
your tiptoe in the start point and the point
after you make 10 steps, and then measure
the distance between them.
The stride becomes larger as you walk faster. *
For measurement, walk at a normal speed.
An average stride is determined by dividing the
walking distance by 10 (number of steps).
Walking distance
A
/
10 (Number of steps) = Stride
13
210
A
Installation conditions
The distance from the speed sensor to the •
computer must be less than 70 cm.
The magnet must pass through the sensor •
zone of the speed sensor.
Click
When the computer
is mounted on the
bracket
Battery holder
Insulation sheet
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi-
tions:(1)This device may not cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
Modifi cations The FCC requires the user to be notifi ed that any changes or modifi cations made to this device
that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment.
Perform the formatting operation according to the following procedure when you use the unit for the fi rst time or restore the unit to the setting at the time of factory shipment.
CATEYE FIT ENGCC-PD100W
Power-saving mode
This unit switches to Sleep at the specifi ed time. To start measurement
during Sleep (Initial setting: 8:00 p.m. through 6:00 a.m.), press any
button to cancel Sleep.
The specifi ed time can be changed according to the life rhythm. *
( ) Change the settings
During measurement, the unit does not switch to Sleep at the specifi ed *
time. In such a case, it switches to Sleep one hour after the measure-
ment is completed.
Resetting data
When the computer clock passes 0:00 in the morning, the measured
data is reset automatically.
Pressing and holding both the * MODE and buttons resets MENU
manually the measured data in the walk
or bike mode currently displayed.
Calorie consumption
The calorie consumption measured by this computer is as follows.
View it as a reference value.
Bike mode : Determined by integrating the value calculated from
the speed in every second.
Walk mode : Determined using RMR (relative metabolic rate), while
targeting women in their 30’s.
1
Switch to the Menu screen
Press and hold the button from MENU
the measuring screen to switch to the
Menu screen.
2
Select SETTING
When the
1.
MODE button is pressed,
“DATA VIEW SETTING” and “ ” will fl ash
alternatively for selection.
Press and hold the 2. MODE button, while
“ ” fl ashes.SETTING
Select the item to change
3
When the
1.
MODE button is pressed, the item will fl ash
alternatively for selection, as shown in Step .4
With the desired item to change fl ashing, press and hold
2.
the button to switch to the setting screen for the MODE
selected item.
Change the settings
4
Refer to the following procedure for setting.
Item Reference
1CLOCK Preparing the computer 5
2DATE Preparing the computer 4
3STRIDE Preparing the computer 8
4WEIGHT Preparing the computer 7
5SLEEP
Sleep time setting
6WHEEL
Tire circumference Preparing the computer 6
7UNIT
Measurement unit Preparing the computer 3
Date setting (
*
DATE) cannot be changed to the date before
the record date of .DATA VIEW
Return to the measuring screen
5
With each press of the button, all changes are MENU
saved, and the unit returns to the setting screen for the
selected item, the Menu screen and then the previous
measuring screen.
Sleep time setting
Change the Sleep start time and
end time. Press the button to MODE
increase the value fl ashing, whereas
press and hold it to switch the item
to set.
The unit does not sleep when the *
Sleep start time is set as the same as
the end time. In this case, the battery
life is shortened.
MENU
Number of
steps
Trip distance
Walking
distance
(Ride)
Calorie
consumption
(Walk)
Carbon offset
(Ride + Walk)
Display period selection screen
DATA VIEW
Example: When “TOTAL” is selected
Carbon offset
icon
Carry
1
Remove the computer from the bracket,
and put it in your pocket or bag.
When the computer is independent, *
the walk icon is turned on, and the
unit switches automatically to the
walk mode.
Start/Stop measurement
2
Measurement automatically starts when
you take more than 6 steps.
Install
1
Install the computer to the bracket.
Install it fi rmly in place until it clicks.*
When the computer is installed, the *
bicycle icon is turned on, and the
unit switches automatically to the
bike mode.
Start/Stop measurement
2
Measurement starts/stops automati-
cally according to the motion of your
bicycle. During measurement, “ ” km/h
or “ ” fl ashes.mph
View the measured result
Carbon offset
The carbon offset icon grows in number as the carbon
offset increases.
How to calculate the carbon offset
The Carbon offset are calculated as follows.
Trip distance (km) x 0.15 = Carbon offset (kg)
This factor of 0.15 is determined by applying the average
value of the overall gasoline-powered passenger cars in
2008 to the equation of the “Carbon offset from 1km drive
of a gasoline-powered car” described on the website of
the Ministry of Land, Infrastructure and Transport and
Tourism (Japan).
DATA VIEW’s display period and update
timing
The data view is updated and the values displayed are re-
set, when the computer clock passes 0:00 in the morning.
(The values reset manually are also refl ected.)
Refer to the following description.
Item Description
TOTAL
The total after starting measurement by this com-
puter can be viewed.
WEEKLY The total over 7 days including today can
be viewed.
TODAY
The measurement data per day can be viewed. The
data of the previous day is stored and the data of
7 days ago is deleted at the time of update at 0:00
in the morning.
Past 6 days
When data is reset manually, it is refl ected as today’s data *
at that moment.
MENU
MODE
Walk mode
In the walk mode, generally the computer
does not display anything. The screen is
turned on once the button is pressed, but
turned off 30 seconds later.
Bike mode
The following screen appears during
measurement. When the screen is turned
off, press any button.
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
(press & hold)
MODE
MODE
MODE
1
Switch to the Menu screen
Press and hold the MENU button to
switch to the Menu screen.
When the Menu screen appears, mea-*
surement will be paused.
2
Select DATA VIEW
Press and hold the button, while MODE
“ ” fl ashes.DATA VIEW
3
Select the display period
1.
When the button is pressed, “MODE TO-
TAL WEEKLY TODAY”, “ ”, “ ”, and Past 6
days will fl ash alternatively for selection,
in this order.
With the desired period fl ashed, press 2.
and hold the button.MODE
View the measured result
4
When the button is pressed, “Distance”, “Number of MODE
steps”, “Calorie consumption”, “Carbon offset” will appear
alternatively for selection, in this order, and the unit returns
to the display period selection screen ( ).3
Return to the measuring screen
5
Press the MENU button to return to the Menu screen.
Press the button again to return to the previous MENU
measuring screen.
During measurement, the unit will resume measurement.*
MENU
Walking
distance
Walk icon Bicycle icon
Change the settings
How to use
Walk (walk mode measuring screen)
Ride on your bicycle (bike mode measuring screen)
Walking time
Elapsed time
Trip distance
Average speed
Maximum
speed
Calorie
consumption
Calorie
consumption
Selected data
With the screen turned on, pressing the
MODE button switches the selected data
in the bottom row of the screen.
Selected data
Pressing the dot section on the front of the
computer switches the selected data in the
bottom row of the screen.
Number of steps
Current speed
Clock
Clock
Speed unit
MODE
MODE
Click
Start time
End time

Produkt Specifikationer

Mærke: Cateye
Kategori: Cykelcomputer
Model: Fit CC-PD100W

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye Fit CC-PD100W stil et spørgsmål nedenfor, og andre brugere vil svare dig


Cykelcomputer Cateye Manualer

Cateye

Cateye Commuter CC-COM10W Manual

16 December 2024
Cateye

Cateye Stealth 10 CC-GL10 Manual

9 December 2024
Cateye

Cateye Strada Smart CC-RD500B Manual

16 November 2024
Cateye

Cateye Padrone Smart plus CC-SC100B Manual

23 Maj 2024
Cateye

Cateye Double Wireless CC-CD300DW Manual

14 April 2024
Cateye

Cateye Stealth evo CC-GL11 Manual

3 April 2024
Cateye

Cateye Velo 9 Manual

14 Marts 2024
Cateye

Cateye Strada CC-RD410DW Manual

27 Februar 2024
Cateye

Cateye e-Train Data IF-TR100 Manual

15 Februar 2024
Cateye

Cateye Strada CC-RD400DW Manual

4 December 2023

Cykelcomputer Manualer

Nyeste Cykelcomputer Manualer

Aplic

Aplic 303208 Manual

30 August 2025
Aplic

Aplic 305673 Manual

30 August 2025
Garmin

Garmin Edge 1050 Manual

30 August 2025
Sunding

Sunding SD-593C Manual

20 August 2025
Garmin

Garmin Edge MTB Manual

24 Juli 2025
VDO

VDO M6.1 Manual

23 Juli 2025
BBB

BBB DashBoard 12 BCP-16W Manual

9 Juli 2025
BBB

BBB NanoBoard 14 BCP-36W Manual

9 Juli 2025
BBB

BBB DashBoard 10 BCP-15W Manual

9 Juli 2025
BBB

BBB DashBoard 7 BCP-05 Manual

9 Juli 2025