Cateye Strada RD200 Cadence Manual

Cateye Cykelcomputer Strada RD200 Cadence

Læs gratis den danske manual til Cateye Strada RD200 Cadence (2 sider) i kategorien Cykelcomputer. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Cateye Strada RD200 Cadence, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

MENUMENUMENU

MODE

MODEMODEMODE MODE

MODE

MODEMODEMODE

MODE

MODEMODEMODE

Tire circumference

reference table

12 x 1.75

14 x 1.50

14 x 1.75

16 x 1.50

16 x 1.75

18 x 1.50

18 x 1.75

20 x 1.75

20 x 1-3/8

22 x 1-3/8

22 x 1-1/2

24 x 1

24 x 3/4

Tubular

24 x 1-1/8

24 x 1-1/4

24 x 1.75

24 x 2.00

24 x 2.125

26 x 7/8

26 x 1(59)

26 x 1(65)

26 x 1.25

26 x 1-1/8

26 x 1-3/8

26 x 1-1/2

26 x 1.40

26 x 1.50

26 x 1.75

26 x 1.95

26 x 2.00

26 x 2.10

26 x 2.125

26 x 2.35

26 x 3.00

27 x 1

27 x 1-1/8

27 x 1-1/4

27 x 1-3/8

650 x 20C

650 x 23C

650 x 35A

650 x 38A

650 x 38B

700 x 18C

700 x 19C

700 x 20C

700 x 23C

700 x 25C

700 x 28C

700 x 30C

700 x 32C

700C Tubular

700 x 35C

700 x 38C

700 x 40C

29 x 2.1

29 x 2.3

935

1020

1055

1185

1195

1340

1350

1515

1615

1770

1785

1753

1785

1795

1905

1890

1925

1965

1920

1913

1952

1953

1970

2068

2100

2005

2010

2023

2050

2055

2068

2070

2083

2170

2145

2155

2161

2169

1938

1944

2090

2125

2105

2070

2080

2086

2096

2105

2136

2146

2155

2130

2168

2180

2200

2288

2326

Tire size L (mm)

MENUMENUMENU

MODE

MODEMODEMODE

L mm

MODE

MODEMODEMODE

When the computer is

mounted on the bracket

3 mm

9 4

444

333

555

Pull

securely

Pull

securely

Pull securely

CATEYE STRADA CADENCE

CYCLOCOMPUTER CC-RD200

U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending

CCRD20-070727 066600520 4

ENG

Before using the computer, please thoroughly read this manual and keep it for

future reference.

Preparing the computer

km/h ↔ mph

Increase Move digits

(by pressing

& holding)

the setting

the

setting

Clear all data (initialization)

Press the button on the back.AC

Select the desired speed units

Select “ ” or “ ”.

Enter the tire circumference

Enter the tire circumference of your bicycle in

mm.

* Refer to the tire circumference reference table.

Set the clock

When MODE is pressed and held, “Displayed time”,

“Hour”, and “Minute” will appear, in this order.

24h ↔

12h, or

increase

the value

Switch the

screen or

move digits

(by pressing

& holding)

the setting

(finish)

Measure wheel circumference (L) of your bike

To get the most accurate calibration do a wheel roll

out. With the valve stem perpendicular to the

ground, mark the pavement at the valve stem. With

the riders weight on the bike, roll the wheel one tire

revolution in a straight line and mark the ground

when the valve stem is perpendicular to the ground

again. Measure the distance in millimeters. This is

the most accurate wheel calibration number.

: Speed unit

: Wheel size icon

Push!

Battery case cover

Contact

WARNING / CAUTION

• Do not concentrate on the computer while riding. Ride safely!

• Install the magnet, sensor, and bracket securely. Check these periodically.

• If a child swallows a battery, consult a doctor immediately.

• Avoid having the computer in direct sunlight for unnecessary or extended periods.

• Do not disassemble the computer.

• Do not drop the computer. Doing so may result in a computer malfunction or damage.

• When using the computer installed on the bracket, change the by pressing on the three dotsMODE

below the screen. Pressing hard on other areas can result in malfunction or damage to the computer.

• Never place the computer on a metal surface. If you do, the contact points will conduct

electricity, discharging the battery.

• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket

threads.

• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

• Dispose of used batteries according to local regulations.

• LCD screen may be distorted when viewed through polarized sunglass lenses.

How to install the unit on your bicycle

Install the speed sensor and wheel magnet

Install the sensor and magnet :

Sensor line

* When installing cadence sensor , insert4

the sensor rubber pad if necessary.7

Magnet

Sensor

Magnet

Sensor

The magnet should pass

through the sensor line.

The clearance between the sensor surface

and the magnet must not exceed 3 mm.

1Bracket band

2Bracket

3Speed sensor

4Cadence sensor

5Wheel magnet

6Cadence magnet

7Sensor rubber pad

8Bracket rubber pad

9Nylon ties (x10)

* After installation, check that the speed sensor and cadence sensor are functioning properly.

In the case of the speed sensor, lift the rear wheel off the ground and spin the wheel to

check the speed is displayed.

In the case of the cadence sensor, press to display (cadence) on the mode screen.MODE C

Rotate the crank in the non driving direction and check cadence is displayed.

If the speed is not displayed, check that conditions

and

are satisfied.

While supporting it

by hand,

push it out as if lifting

the front up

Rear wheel spoke

Toward the sensor line

Remove/install the

computer

Install the cadence sensor and cadence magnet

Left crank (Inside)

Toward the sensor line

Caution:

Round off the cut edge of the

bracket band to prevent injury.

Cut

Attach the bracket to the stem or handlebar

Caution:

Tighten the bracket, ensuring that the

cable does not get caught in the stem.

Stem

Handlebar

Caution:

Tighten the bracket, ensuring that the cable

does not get caught in the handlebar.

Route the cable

Caution:

Turn the handlebar to make

sure wire does not hinder full

rotation.

When attaching the bracket to the handlebar

When attaching the bracket to the stem

Use the nylon tie to secure9

the cable on the frame. Wind

the cable on the rear brake

cable as shown.

Left Chain Stay (Inside)

Left Chain Stay (Outside)

Click

Standard Parts

#160-2090

Parts kit

#160-0280

Braket band

#160-2093

Braket/Sensor

#169-6180

Lithium battery

(CR1620)

#169-9691

Wheel magnet

#169-9766

Cadence magnet

MODE

MODEMODE

MODE

MODEMODE

MODE

MODEMODE

MODE

MENUMENUMENU

MODE

MODEMODEMODE

LIMITED WARRANTY

2-Year Computer only

(Accessories/Bracket sensor and Battery Consumption excluded)

CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years

from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no

charge. Service must be performed by CatEye or an authorized retailer.

To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for

repair. Please write or type your name and address clearly on the warranty certificate.

Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.

For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory

rights.

CO.,LTD.

2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan

Attn: CATEYE Customer Service Section

Service & Research Address for USA

CATEYE Service and Research Center

1705 14th St. 115 Boulder, CO 80302

Phone: 303.443.4595

Toll Free: 800.5CATEYE

Fax: 303.473.0006

E-mail: service@cateye.com

URL: http://www.cateye.com

CC-RD200

Wheel selection ..... Toggle between the specified wheel size (tire circumference)

and . Use this function if the computer is to be shared

between two bicycles.

Pressing MODE toggles between and .

Wheel size entry .... Pressing MODE increases the value, and pressing and

holding moves to the next digit.MODE

* To enter the wheel size , display using Wheel selection“ ”.

Clock setting .......... To .set the clock, refer to “Preparing the computer-4”

Total distance manual entry

................................ Before reinitializing the computer, note the total distance. This

reading will later allow you to enter the total distance

manually. Pressing increases the value, and pressingMODE

and holding moves to the next digit.MODE

Speed unit .............. Pressing MODE toggles between and .

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth,

and wipe it off with a dry cloth.

Replacing the battery

If the display appears faded, replace the battery.

Install a new lithium battery (CR1620) with the (+)

side facing upward. Then reinitialize the computer

referring to Preparing the computer“ ”.

Starting/Stopping measurement

Measurements occur automatically

when the bicycle is in use. During

measurement, or flashes.

Switching computer function

Pressing MODE switches function,

in order, as shown on the left.

Resetting data

To reset measurement data, display

any data other than for and thenDst-2

press and hold . Pressing andMODE

holding MODE with Dst-2 displayed

resets Dst-2 only.

The total distance is never reset.

Power-saving function

If the computer has not received

any signal for an hour, power-

saving mode will activate and only

the clock will be displayed.

Alternatively, if the sensor detects a

signal or is pressed, the mainMODE

display reappears.

Pace arrow

Indicates whet her the current

speed is faster ( ) or slower ( )

than the average speed.

Operating the computer [Measuring screen]

Tm Elapsed Time

0:00 00 59’ ” - 9:59’ ”

C Cadence

0(20) - 299 rpm

Dst Trip Distance

0.00 - 999.99 km [mile]

Dst

Trip Distance-2

0.00 - 999.99 /

1000.0 - 9999.9 km [mile]

Av Average Speed*2

0.0 - 200.0 km/h

[0.0 - 125.0 mph]

Mx Maximum Speed

0.0(4.0) - 200.0 km/h

[0.0(3.0) - 125.0 mph]

Odo Total Distance

0.0 - 9999.9 /

10000 - 99999 km [mile]

Clock

0:00 - 23:59

or 1:00 - 12:59

*1 With the computer installed on the bracket,

press on the three raised dots on the face of

the computer.

*2 If Tm exceeds approximately 27 hours or

DST .E exceeds 999.99 km, (Error) is

displayed as the average speed. Reset data.

Changing the computer settings [menu screen]

To bring up the menu screen, press MENU in any mode. Each time isMODE

pressed, the relevant menu screen appears. Pressing and holding MODE

changes the setting of the displayed menu.

Current speed

0.0(4.0) - 200.0 km

[0.0(3.0) - 125.0 mph]

Speed

The contacts to be short-

circuited intermittently are

located on the back.

Selected Mode

Wheel

selection

Wheel size entry Clock setting Total distance

manual entry

Speed unit

* After changing, be sure to press to register the setting.MENU

* If the menu screen is not touched for a minute, the Measuring

screen reappears without data changes.

Setting

change (by

pressing &

holding)

Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the computer.

Wash off the bracket with water to get rid of any dirt, and to ensure that the computer slides in and out smoothly.

Speed (Cadence) are not displayed. (Touch a metal item against two contact points of

the computer several times to create a short circuit while observing the display. If a

numeric value appears, this signifies that the computer is functioning normally.)

Is the clearance between the sensor and magnet too great? (must be

≤

3 mm)

Does the magnet pass through the sensor line?

Adjust the positions of the magnet and sensor.

Is there any foreign matter (which would prevent a clean contact) on the contact points of the computer and/or

bracket?

Clean the contact points.

Check that no wire cable is worn or broken. Even with a normal appearance, it may be that a wire cable could be

broken internally.

Replace the bracket sensor set.

No display.

Is battery in the computer run down?

Replace it. Then reinitialize the computer referring to Preparing the computer“ ”.

Incorrect data appear.

Reinitialize the computer referring to “Preparing the computer”.

Specification

Battery ...................................... Lithium battery (CR1620) x 1

Battery life ................................ Approx. 2 years (Using the battery one hour a day; the battery life will vary with the

conditions of use.)

Controller .................................. 4-bite, 1-chip microcomputer (Crystal controlled oscillator)

Display ...................................... Liquid crystal display

Sensor ...................................... No contact magnetic sensor

Wheel circumference range ..... 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm)

Working temperature ............... 32 ° ° °F - 104 F (0 C - 40 C) (This product will not function appropriately when exceeding the°

Working Temperature range. Slow response or black LCD at lower or higher temperature

may happen respectively.)

Dimensions/weight 3/64................... 1-5 ” x 1-7/32” x 19/32 (46.5 x 31 x 15 mm) / 0.63 oz (18 g)”

* The factory-loaded battery life might be shorter than the above-mentioned specification.

* The specifications and design are subject to change without notice.

COIN

CR1620

Open

Cadence

Produkt Specifikationer

Mærke:	Cateye
Kategori:	Cykelcomputer
Model:	Strada RD200 Cadence

Har du brug for hjælp?

Hvis du har brug for hjælp til Cateye Strada RD200 Cadence stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykelcomputer Cateye Manualer

Cateye Commuter CC-COM10W Manual

16 December 2024

Cateye Stealth 10 CC-GL10 Manual

9 December 2024

Cateye Strada Smart CC-RD500B Manual

16 November 2024

Cateye Padrone Smart plus CC-SC100B Manual

23 Maj 2024

Cateye Double Wireless CC-CD300DW Manual

14 April 2024

Cateye Stealth evo CC-GL11 Manual

3 April 2024

Cateye Velo 9 Manual

14 Marts 2024

Cateye Strada CC-RD410DW Manual

27 Februar 2024

Cateye e-Train Data IF-TR100 Manual

15 Februar 2024

Cateye Strada CC-RD400DW Manual

4 December 2023

Cykelcomputer Manualer

Nyeste Cykelcomputer Manualer

Aplic 303208 Manual

30 August 2025

Aplic 305673 Manual

30 August 2025

Garmin Edge 1050 Manual

30 August 2025

Sunding SD-593C Manual

20 August 2025

Garmin Edge MTB Manual

24 Juli 2025

VDO M6.1 Manual

23 Juli 2025

BBB DashBoard 12 BCP-16W Manual

9 Juli 2025

BBB NanoBoard 14 BCP-36W Manual

9 Juli 2025

BBB DashBoard 10 BCP-15W Manual

9 Juli 2025

BBB DashBoard 7 BCP-05 Manual

9 Juli 2025