Celestron SkyScout 93980 Manual

Celestron Ikke kategoriseret SkyScout 93980

Læs gratis den danske manual til Celestron SkyScout 93980 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Celestron SkyScout 93980, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation

1. Insert the hand control cable connector into the SkyScout Connect’s hand control port.

2. Insert the SkyScout Connect’s interface connector into the RS232 port

at the bottom of the hand control.

3. Seat the hand control’s cord in a concentric pattern within the

open space inside the SkyScout Connect.

4. Align the SkyScout Connect’s bottom tabs into the bottom holes

of the hand control, and press in the top of the hand control until

it snaps into the SkyScout Connect. Make sure the hand control

cord is seated securely inside the unit.

5. Insert the USB connector (smaller end) into the SkyScout’s

USB port and insert the larger USB connector into the USB port

located on the bottom of the SkyScout Connect.

6. Attach the SkyScout Connect’s coiled cable into the telescope’s

hand control or AUX port.

#93980 – SKYSCOUT CONNECT

Installation 3

NOTE: The SkyScout Connect will attach directly inside the fork arm for all NexStar SE series. For CPC owners, use

the supplied plastic holder and attach to the fork arm. For Advanced Series and CGE owners, use the supplied holder and

strap to attach unit to the tripod leg.

Installation 1

Installation 6

Installation 5a

Installation 5b

Installation 2

NexStar® SE Series CPC® GPS Series Advanced/CGE™ Series

Power-On Operation

1. Power on your telescope and then power on the SkyScout (Telescope must be powered on FIRST), the “HC” and “SS”

LEDs will blink to indicate that the SkyScout Connect is linking.

2. When both LEDs stop blinking, the SkyScout Connect has established a link with the hand control and SkyScout.

3. Begin the telescope alignment procedure as described in your telescope’s owner’s manual.

SkyScout as a GPS Accessory

Before use, verify the correct rmware is installed (Version 1.28.12 or higher). If not, go to www.celestron.com/skyscout/

and download the latest rmware.

For non-GPS telescopes or mounts, the SkyScout Connect can be used as a GPS accessory and will allow the GPS time

and location to be downloaded from the SkyScout to the telescope or mount.

The GPS must be enabled to “On” in the hand control Utilities menu once the telescope is powered on. If the SkyScout

has not acquired the GPS time and location, the hand control will not display the correct time. The hand control will

update this information once GPS is acquired.

SkyScout Operation

When the SkyScout Connect is communicating with the SkyScout, a telescope icon on the SkyScout’s LCD screen will be

displayed. This will enable the “Point Telescope” menu item to be displayed on an object’s information screen. By selecting

“Point Telescope” feature, the SkyScout will direct the telescope to slew to the selected object.

“Point Telescope” Operation

1. Ensure the telescope is properly aligned and both LED lights on the SkyScout Connect are solid red.

2. Using the SkyScout, select the Identify feature to identify an object and press the Target button. Hit Select and

“Point Telescope” will be highlighted in the object menu screen. Hit Select again and the telescope will slew to the

selected object.

3. For locating an object, choose the Locate feature and locate the selected object. Press the down arrow button to

highlight “Point Telescope” and press Select. The telescope will then slew to the selected object.

HELPFUL HINT: It is ok to disconnect the SkyScout from the SkyScout Connect and use it independently once

connection is established. To reestablish connection, simply replug the SkyScout to continue “Point Telescope” operation.

Troubleshooting

1. If the “HC” LED indicates an error (continues to blink without connecting), check the SkyScout Connect’s interface

cable and the RS232 port connection on the bottom of the hand control. To clear the error, check and make sure the

cable is seated properly and power-cycle the telescope.

2. If the “SS” LED indicates an error (continues to blink without connecting), check the USB cable and make sure it’s

connected properly. To clear the error, remove the USB cable, power-cycle the SkyScout and reconnect the USB cable.

3. If the telescope is not pointing to an object accurately, make sure the time zone and Standard or Daylight Savings Time

is identical for both the SkyScout and telescope. If not, change the settings in your telescope’s hand control under

Setup Time-Site in the Scope Setup menu.

CELEsTrON, 2835 Columbia Street, Torrance, CA 90503 • Phone (310) 328-9560 • Fax (310) 212-5835

Warranty: Two year limited warranty. See the Celestron Accessory Catalog (#93980) for complete warranty details or contact Celestron

Produkt Specifikationer

Mærke:	Celestron
Kategori:	Ikke kategoriseret
Model:	SkyScout 93980

Har du brug for hjælp?

Hvis du har brug for hjælp til Celestron SkyScout 93980 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Celestron Manualer

Celestron Smart DewHeater and Controller 2x Manual

5 September 2024

Celestron Thermistor 94037 Manual

5 September 2024

Celestron StarPointer Finderscope Manual

4 September 2024

Celestron OMNI AZ 102 Manual

20 August 2024

Celestron StarSense Explorer 10 Manual

19 August 2024

Celestron PowerTank 18763 Manual

15 August 2024

Celestron EclipSmart Manual

14 August 2024

Celestron PowerSeeker Manual

9 August 2024

4 August 2024

Celestron 18774 Manual

2 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive IAN 304090 Manual

16 Juni 2025

Toorx SRX-85 Manual

16 Juni 2025

Cable Matters 180070 Manual

16 Juni 2025

Philips Avent SCD252 Manual

16 Juni 2025

Philips Q-Line 55BDL2050Q Manual

16 Juni 2025

EFX Delta DUDB4 Manual

16 Juni 2025

Foster Prep Station PS1000HR Manual

16 Juni 2025

OmniMount OBT60 Manual

16 Juni 2025

XO D34HPBF Manual

16 Juni 2025

Janitza 800-DI14 Manual

16 Juni 2025