Chamberlain KLIK3U-BL2 Manual

Chamberlain Joystick KLIK3U-BL2

Læs gratis den danske manual til Chamberlain KLIK3U-BL2 (51 sider) i kategorien Joystick. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Chamberlain KLIK3U-BL2, eller vil du spørge andre brugere om produktet?

Side 1/51
To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control
transmitters.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
Models KLIK3U, KLIK3U-BK,
KLIK3U-BL, KLIK3U-BK2, KLIK3U-BL2,
KLIK3U-SS, KLIK3C, KLIK3C-BK,
KLIK3C-BL, KLIK3C-SS, KLIK3C-BK2,
KLIK3C-BL2
Read instructions thoroughly BEFORE beginning.
If using the Universal Remote Control with residential door openers, the remote control must be used only with
door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always
located on or near the bottom of the door track.
STOP
UNIVERSAL REMOTE
CONTROL
WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause
cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
2
GETTING STARTED
The remote control can be programmed to activate up to two products, such as a garage door opener, gate operator, or
commercial door operator. The images throughout this manual are for reference only and your product may look different.
Button 2
Programmed separately from Button 1.
Garage Door Opener Commercial Door OperatorGate Operator
Button 1
Programmed separately from Button 2.
Program Button
Used for programming products with LEARN buttons.
Depending on your product, there is a button (LEARN button) or DIP switches used for programming. You will need to locate the
LEARN button or DIP switches on your product before you start programming.
DIP Switches
Used for programming products with DIP switches.
GARAGE DOOR OPENERS
The LEARN button or DIP switches are typically located on the back or
side panel of your garage door opener. Your LEARN button may have a
different name (SMART button, PROGRAM button, SET button, etc.). For
help locating your LEARN button or DIP switches refer to the Help
section in this manual or contact your garage door opener manufacturer.
COMMERCIAL DOOR OPERATORS
The LEARN button or DIP switches are typically located on the logic
board of your operator. Your LEARN button may have a different name
(RADIO button, XMITTER button, etc.). For help locating your LEARN
button or DIP switches contact your door operator manufacturer.
GATE OPERATORS
The LEARN button or DIP switches are typically located on the control
board of your operator. Your LEARN button may have a different name
(RADIO button, XMITTER button, etc.). For help locating your LEARN
button or DIP switches contact your gate operator manufacturer.
EXTERNAL RECEIVER
Some products do not
have a LEARN button or
DIP switches. In this
case, the LEARN button
or DIP switches will be
located in an external
receiver. The receiver will
be located on the product
or mounted nearby.
Follow the programming
instructions for an
external receiver.


Produkt Specifikationer

Mærke: Chamberlain
Kategori: Joystick
Model: KLIK3U-BL2

Har du brug for hjælp?

Hvis du har brug for hjælp til Chamberlain KLIK3U-BL2 stil et spørgsmål nedenfor, og andre brugere vil svare dig