Chief NAC25H Manual

Chief Ikke kategoriseret NAC25H

Læs gratis den danske manual til Chief NAC25H (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Chief NAC25H, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

6436 City West Parkway, Eden Prairie, MN 55344

• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918

8821-002014 Rev01

a Duchossois Group Company

04/12

NAC25H E1/G1/S1 Racks Casters

The NAC25H casters are designed for use with Chief® E1, G1 or S1 Series racks. See the specific installation instructions provided with the

rack for additional installation information.

TOOLS REQUIRED / PARTS INCLUDED

WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAN RESULT IN SERIOUS

PERSONAL INJURY, DAMAGE TO EQUIPMENT, OR VOIDING OF FACTORY WARRANTY! It is the installer’s responsibility to make

sure all components are properly assembled and installed using the instructions provided.

NOTE: Casters may be installed using a torque wrench, and torque not to exceed 5 ft-lbs.

A (4)

[Casters]

B (16)

1/4-20 D (16)

1/4-20 x 1/2"

C (16)

1/4-20 x 5/8"

7/16"

NOTE: Not all fasteners will be used.

E1/G1 Racks Caster Installation

1. Attach a caster (A) to each lower corner of the E1 rack using four

1/4-20 x 5/8" Phillips truss head machine screws (C) [OR four

1/4-20 x 1/2" hex head cap screws (D)] and four 1/4-20 lock nuts

(B) for each caster. (See Figure 1)

Figure 1

NOTE: If levelers are already installed in the rack, leave

levelers installed and adjust them using a 13mm

wrench so they are as close to the floor as possible,

yet still allow movement of the rack on the casters.

S1 Racks Caster Installation

1. Attach a caster (A) to each lower corner of the S1 rack using four

1/4-20 x 1/2" hex head cap screws (D) [OR four 1/4-20 x 5/8"

Phillips truss head machine screws (C)] for each caster. (See

Figure 2)

Figure 2

NOTE: If levelers are already installed in the rack, leave

levelers installed and adjust them using a 13mm

wrench so they are as close to the floor as possible,

yet still allow movement of the rack on the casters.

(NE1F2823 rack shown with fasteners B & C)

(A)

(B) x 4

(D) x 4

(NS1F1223 rack shown with fasteners D)

(A)

(D) x 4

Produkt Specifikationer

Mærke:	Chief
Kategori:	Ikke kategoriseret
Model:	NAC25H

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief NAC25H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chief Manualer

13 November 2025

11 November 2025

9 November 2025

6 November 2025

3 November 2025

1 November 2025

31 Oktober 2025

30 Oktober 2025

29 Oktober 2025

Chief KTA1004S Manual

29 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ELO E121405 Manual

2 December 2025

BakkerElkhuizen BE Flexible Dual Manual

2 December 2025

2 December 2025

2 December 2025

2 December 2025

2 December 2025

2 December 2025

Vevor W1.2×760 Manual

2 December 2025

Vevor XCW-160LS Manual

2 December 2025

Vevor SC13000 Manual

2 December 2025