Chief PLP2000B Manual

Chief Flad panel støtte PLP2000B

Læs gratis den danske manual til Chief PLP2000B (8 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Chief PLP2000B, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
CHIEF MANUFACTURING INC. 8805-000183 Rev F
1-800-582-6480 952-894-6280 FAX 952-894-6918 ©2008 Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 03/08
I N S T A LL A T I O N IN S T R U C T IO N S
PLP Series Wall Mount
The PLP Series wall mount accommodates large flat
screens weighing up to 200 lbs (90.72kg). The teardrop
holes in the mount allow for quick connect/disconnect of
the screen, thus simplifying installation and maintenance
processes.
The top and bottom mounting brackets are adaptable to
supporting framework with wood studs that are 16” on
center or 24”on center.
The mount has integrated lateral shift, allowing for four
different mounting options. For dual wood studs 16” on
center, the lateral shift is + 4.5 inches. For dual wood
studs 24” on center, the lateral shift is + 0.5 inches.
The display can be pulled and tilted by hand into any
position in the zero-to-15 degree tilt range and remain
stationary.
The bottom of the mount pulls forward 4” from the wall
and locks into place for installation of cable connections.
The mount also uses Chief’s exclusive Q-Latch™
mounting system, which offers quick connect/disconnect
display mounting. The display is secured to the mount
with a latching flag. For additional security, you can lock
the latching flag in place by adding a padlock. PLP Series
Installation Instructions PLP Series
2
! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation. OSHPD documents and drawings are available at
www.chiefmfg.com, and located on the product information page for the mount.
BEFORE YOU BEGIN
CAUTION: To prevent damage to your monitor and PLP, which could affect or void the Factory
warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay
particular attention to the Warnings and Cautions in this document.
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the
mount must be capable of supporting five times the total weight of the equipment.
The maximum weight to be installed on the PLP Series wall mount is 200 lbs (90.72kg).
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-
6480.
IMPORTANT WARNINGS and CAUTIONS!
WARNING A WARNING alerts you to the possibility of serious injury or death if you do not
follow the instructions.
CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do
not follow the corresponding instructions.
WARNING Improper installation can result in serious personal injury! Make sure that the
structural members can support a redundant weight factor five times the total weight
of the equipment. If not, reinforce the structure before installing the mount.
WARNING Be aware of the potential for personal injury or damage to the equipment if it is not
installed correctly. Consider the weight of the mount without the display.
WARNING The installer is responsible for verifying that the display to which the wall mount is
fastened will safely support the combined load of all attached components or other
equipment.
WARNING The combined weight of the display placed on the wall mount must not exceed 200 lbs
(90.72kg),the maximum support weight of the mount.
WARNING Watch for pinch points. Do not put your fingers between movable parts.
WARNING Make sure the flag securing the display is completely lowered at all times except when
removing or installing the display. The flag must be all the way down when
installing/removing cables.
CAUTION Check the unit for shipping damage before you begin the installation.

Produkt Specifikationer

Mærke: Chief
Kategori: Flad panel støtte
Model: PLP2000B

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief PLP2000B stil et spørgsmål nedenfor, og andre brugere vil svare dig


Flad panel støtte Chief Manualer

Chief

Chief MWCU Manual

3 April 2025
Chief

Chief KITXWXSM1U Manual

3 April 2025
Chief

Chief RLXT3 Manual

3 April 2025
Chief

Chief LPE1U Manual

2 April 2025
Chief

Chief MFCUS Manual

9 Marts 2025
Chief

Chief TS318TU Manual

30 Januar 2025
Chief

Chief TS318SU Manual

30 Januar 2025
Chief

Chief PWCU Manual

15 Januar 2025
Chief

Chief MIWRFUB Manual

15 Januar 2025
Chief

Chief TILD1X5NE1-M Manual

15 Januar 2025

Flad panel støtte Manualer

Nyeste Flad panel støtte Manualer

Anywhere Cart

Anywhere Cart AC-GO-16 Manual

2 April 2025
Proaim

Proaim P-DMC Manual

2 April 2025
Proaim

Proaim CT-VNGD-CS Manual

2 April 2025
Mount-It!

Mount-It! MI-7919 Manual

2 April 2025
Mount-It!

Mount-It! MI-384 Manual

2 April 2025
Proaim

Proaim CT-VNGD-UC5 Manual

2 April 2025
Premier Mounts

Premier Mounts 7170-0977 Manual

2 April 2025
Mount-It!

Mount-It! MI-766 Manual

2 April 2025
Erard

Erard FLAK 800+ Manual

2 April 2025
Metronic

Metronic 451060 Manual

28 Marts 2025