Chief SLB087 Manual

Chief fladskærmsbeslag SLB087

Læs gratis den danske manual til Chief SLB087 (1 sider) i kategorien fladskærmsbeslag. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 29 anmeldelser. Har du et spørgsmål om Chief SLB087, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-

mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The

information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the

information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8850-00076

7/19/06

SLB-087 and SLM-087 Interface Brackets

SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling

1-800-582-6480.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation:

WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE

TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.

1. Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place three, 1/2" spacers over three threaded inserts in bottom of projector.

4. Place Interface bracket onto bottom of projector, aligning mounting mounting holes and spacers.

5. Secure Interface bracket to projector using three M4 x 20mm Philips flat head screws and flat washers.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the

All-Points Security Kit.

(1) Interface Bracket (3) Screw, Philips Flat Head, Machine, M4 x 20mm ****

(6) 10-24 Thumb Nuts ** (3) 1/2" x .194 x 1/2" Nylon Spacer ****

(1) All-Points Security Kit

**Only used when installing SLB Interface brackets.

****Used when mounting surface of projector is recessed.

Produkt Specifikationer

Mærke:	Chief
Kategori:	fladskærmsbeslag
Model:	SLB087

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLB087 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

fladskærmsbeslag Chief Manualer

Chief SLB087 Manual

17 August 2024

Chief Manualer

Chief TILSC3HUU Manual

12 November 2025

Chief TIL1X3PT Manual

12 November 2025

11 November 2025

11 November 2025

11 November 2025

11 November 2025

9 November 2025

Chief PAC525FWP2 Manual

8 November 2025

Chief FCAVCSU80 Manual

8 November 2025

Chief TILVABPT Manual

7 November 2025