Chief SLB133 Manual

Chief Flad panel støtte SLB133

Læs gratis den danske manual til Chief SLB133 (1 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 75 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 38 anmeldelser. Har du et spørgsmål om Chief SLB133, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000122 Rev01
a Duchossois Group Company
05/09
SSB-133, SSM-133, SLB-133 and SLM-133 Interface Brackets
SSB-133, SSM-133, SLB-133 and SLM-133 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place 1/4" spacers over front threaded inserts and the 1/2" spacers over the rear threaded inserts in bottom of projector.
4. Place interface bracket onto projector bottom and align the mounting holes in bracket with threaded inserts in projector.
5. Using M4 x 12mm Phillips flat head screws and M4 x 20mm Phillips flat head screws, secure interface bracket to projector and tighten all
fasteners at this time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (2) Screw, Phillips Flat Head, Machine, M4 x 12mm ****
(4) 10-24 Thumb Nuts ** (2) Screw, Phillips Flat Head, Machine, M4 x 20mm ****
(1) All-Points Security Kit (2) 1/2" x .194" x 1/2" Round Spacer ****
(2) 1/2" x .218" x 1/4" Round Spacer ****
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-133 SLM-133
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interface
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector

Produkt Specifikationer

Mærke: Chief
Kategori: Flad panel støtte
Model: SLB133
Produktfarve: Sort
Kompatible produkter: PLUS U7-132, U7-132h, U7-137
Maksimal vægtkapacitet: - kg

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLB133 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Flad panel støtte Chief Manualer

Chief

Chief MWCU Manual

3 April 2025
Chief

Chief KITXWXSM1U Manual

3 April 2025
Chief

Chief RLXT3 Manual

3 April 2025
Chief

Chief LPE1U Manual

2 April 2025
Chief

Chief MFCUS Manual

9 Marts 2025
Chief

Chief iCSPFM1T02 Manual

4 Marts 2025
Chief

Chief TS318TU Manual

30 Januar 2025
Chief

Chief TS318SU Manual

30 Januar 2025
Chief

Chief PWCU Manual

15 Januar 2025
Chief

Chief MIWRFUB Manual

15 Januar 2025

Flad panel støtte Manualer

Nyeste Flad panel støtte Manualer

Anywhere Cart

Anywhere Cart AC-GO-16 Manual

2 April 2025
Proaim

Proaim P-DMC Manual

2 April 2025
Proaim

Proaim CT-VNGD-CS Manual

2 April 2025
Mount-It!

Mount-It! MI-7919 Manual

2 April 2025
Mount-It!

Mount-It! MI-384 Manual

2 April 2025
Proaim

Proaim CT-VNGD-UC5 Manual

2 April 2025
Premier Mounts

Premier Mounts 7170-0977 Manual

2 April 2025
Mount-It!

Mount-It! MI-766 Manual

2 April 2025
Erard

Erard FLAK 800+ Manual

2 April 2025
Metronic

Metronic 451060 Manual

28 Marts 2025