Chief SLB275 Manual

Chief Flad panel støtte SLB275

Læs gratis den danske manual til Chief SLB275 (1 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Chief SLB275, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-002072 Rev00

a Duchossois Group Company

11/10

SSB-275, SSM-275, SLB-275 and SLM-275 Interface Brackets

SSB-275, SSM-275, SLB-275 and SLM-275 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the threaded inserts in the

bottom of the projector and ensuring that triangle in bracket points towards front of projector.

4. Position M6 x 10mm mounting screws with M6 flat washers into the threaded inserts and three bracket side tabs. Position 1/2" tall spacer

underneath threaded insert and mounting hole at front of interface bracket. Place the M6 x 20mm screw into the threaded insert and

mounting hole at front of interface bracket and through 1/2" spacer. Tighten all fasteners at this time, securing the bracket to the projector.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation

instructions in the All-Points Security Kit.

(1) Interface Bracket (3) Screw, Phillips Pan Head, Machine, M6 x 10mm

(4) 10-24 Thumb Nuts ** (1) Screw, Phillips Flat Head, Machine, M6 x 20mm

(3) Washer, M6

(1) All-Points Security Kit (1) 5/32" Hex Key

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.

DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.

Note: SSB-style interface bracket connections are circled.

Note: SSM-style interface bracket connections are circled.

SLB-275

SLM-275

Towards front

of projector

Towards front

of projector

(1) Nylon Spacer, 1/2" x .316" x 1/2"

Produkt Specifikationer

Mærke:	Chief
Kategori:	Flad panel støtte
Model:	SLB275

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLB275 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Flad panel støtte Chief Manualer

Chief MWCU Manual

3 April 2025

Chief KITXWXSM1U Manual

3 April 2025

Chief RLXT3 Manual

3 April 2025

Chief LPE1U Manual

2 April 2025

Chief MFCUS Manual

9 Marts 2025

Chief iCSPFM1T02 Manual

4 Marts 2025

30 Januar 2025

30 Januar 2025

15 Januar 2025

15 Januar 2025

Flad panel støtte Manualer

Nyeste Flad panel støtte Manualer

Anywhere Cart AC-GO-16 Manual

2 April 2025

Proaim P-DMC Manual

2 April 2025

Proaim CT-VNGD-CS Manual

2 April 2025

Mount-It! MI-7919 Manual

2 April 2025

Mount-It! MI-384 Manual

2 April 2025

Proaim CT-VNGD-UC5 Manual

2 April 2025

Premier Mounts 7170-0977 Manual

2 April 2025

Mount-It! MI-766 Manual

2 April 2025

Erard FLAK 800+ Manual

2 April 2025

Metronic 451060 Manual

28 Marts 2025