Chief SLM191 Manual

Chief Flad panel støtte SLM191

Læs gratis den danske manual til Chief SLM191 (1 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Chief SLM191, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000260 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-191, SSM-191, SLB-191 and SLM-191 Interface Brackets
SSB-191, SSM-191, SLB-191 and SLM-191 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place 1/2" nylon spacers over the threaded inserts in the bottom of the projector.
4. Place the interface bracket onto the 1/2" nylon spacers on the bottom of the projector and align the mounting holes in the bracket with the
nylon spacers.
5. Using the M4 x 20mm pan head screws and M4 washers, position screws with washers into the side holes and position the M4 flat head
screws in the counter sink holes. Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (2) Screw, Phillips pan head, M4 x 20mm
(4) 10-24 Thumb Nuts ** (2) Screw, Phillips flat head, M4 x 20mm
(1) All-Points Security Kit (4) Spacer, Nylon, 1/2" x .194 x 1/2"
(2) Washer, Flat, M4
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-191 SLM-191
(
N
o
t
e
:
S
S
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interfa
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector

Produkt Specifikationer

Mærke: Chief
Kategori: Flad panel støtte
Model: SLM191

Har du brug for hjælp?

Hvis du har brug for hjælp til Chief SLM191 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Flad panel støtte Chief Manualer

Chief

Chief MWCU Manual

3 April 2025
Chief

Chief KITXWXSM1U Manual

3 April 2025
Chief

Chief RLXT3 Manual

3 April 2025
Chief

Chief LPE1U Manual

2 April 2025
Chief

Chief MFCUS Manual

9 Marts 2025
Chief

Chief TS318TU Manual

30 Januar 2025
Chief

Chief TS318SU Manual

30 Januar 2025
Chief

Chief PWCU Manual

15 Januar 2025
Chief

Chief MIWRFUB Manual

15 Januar 2025
Chief

Chief TILD1X5NE1-M Manual

15 Januar 2025

Flad panel støtte Manualer

Nyeste Flad panel støtte Manualer

Anywhere Cart

Anywhere Cart AC-GO-16 Manual

2 April 2025
Proaim

Proaim P-DMC Manual

2 April 2025
Proaim

Proaim CT-VNGD-CS Manual

2 April 2025
Mount-It!

Mount-It! MI-7919 Manual

2 April 2025
Mount-It!

Mount-It! MI-384 Manual

2 April 2025
Proaim

Proaim CT-VNGD-UC5 Manual

2 April 2025
Premier Mounts

Premier Mounts 7170-0977 Manual

2 April 2025
Mount-It!

Mount-It! MI-766 Manual

2 April 2025
Erard

Erard FLAK 800+ Manual

2 April 2025
Metronic

Metronic 451060 Manual

28 Marts 2025